18 Matching Results

Search Results

Advanced search parameters have been applied.
in creator/contributor: "Wang, Shuping"  
Results: 1 - 18
open access

Cold-formed Steel Framed Shear Wall Sheathed with Corrugated Sheet Steel

Description: Incombustibility is one important advantage of the sheet steel sheathed shear wall over wood panel sheathed shear wall. Compared to shear wall sheathed with plywood and OSB panel, shear wall sheathed with flat sheet steel behaved lower shear strength. Although shear wall sheathed with corrugated sheet steel exhibited high nominal strength and high stiffness, the shear wall usually behaved lower ductility resulting from brittle failure at the connection between the sheathing to frames. This rese… more
Date: May 2013
Creator: Yu, Guowang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Two-Phase Spray Cooling with HFC-134a and HFO-1234yf for Thermal Management of Automotive Power Electronics using Practical Enhanced Surfaces

Description: The objective of this research was to investigate the performance of two-phase spray cooling with HFC-134a and HFO-1234yf refrigerants using practical enhanced heat transfer surfaces. Results of the study were expected to provide a quantitative spray cooling performance comparison with working fluids representing the current and next-generation mobile air conditioning refrigerants, and demonstrate the feasibility of this approach as an alternative active cooling technology for the thermal manag… more
Date: August 2017
Creator: Altalidi, Sulaiman Saleh
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Dynamic Behaviors of Historical Wrought Iron Truss Bridges – a Field Testing Case Study

Description: Civil infrastructure throughout the world serves as main arteries for commerce and transportation, commonly forming the backbone of many societies. Bridges have been and remain a crucial part of the success of these civil networks. However, the crucial elements have been built over centuries and have been subject to generations of use. Many current bridges have outlived their intended service life or have been retrofitted to carry additional loads over their original design. A large number of t… more
Date: December 2015
Creator: Hedric, Andrew C.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Impact of Green Design and Technology on Building Environment

Description: Currently, the public has a strong sense of the need for environment protection and the use of sustainable, or “green,” design in buildings and other civil structures. Since green design elements and technologies are different from traditional design, they probably have impacts on the building environment, such as vibration, lighting, noise, temperature, relative humidity, and overall comfort. Determining these impacts of green design on building environments is the primary objective of this st… more
Date: December 2015
Creator: Xiong, Liang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Energy Harvesting Wireless Piezoelectric Resonant Force Sensor

Description: The piezoelectric energy harvester has become a new powering option for some low-power electronic devices such as MEMS (Micro Electrical Mechanical System) sensors. Piezoelectric materials can collect the ambient vibrations energy and convert it to electrical energy. This thesis is intended to demonstrate the behavior of a piezoelectric energy harvester system at elevated temperature from room temperature up to 82°C, and compares the system’s performance using different piezoelectric materials.… more
Date: December 2013
Creator: Ahmadi, Mehdi
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Investigations of the Fresnel Lens Based Solar Concentrator System through a Unique Statistical-Algorithmic Approach

Description: This work investigates the Fresnel-lens-based solar concentrator-receiver system in a multi-perspective manner to design, test and fabricate this concentrator with high-efficiency photon and heat outputs and a minimized effect of chromatic aberrations. First, a MATLAB®-incorporated algorithm optimizes both the flat-spot and the curved lens designs via a statistical ray-tracing methodology of the incident light, considering all of its incidence parameters. The target is to maximize the solar ray… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2019
Creator: Qandil, Hassan Darwish Hassan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Algorithmically Optimized Hemispherical Dome as a Secondary Optical Element for the Fresnel Lens Solar Concentrator

Description: This article focuses on a way to maximize the concentration acceptance product (CAP), while using the minimum SOE and receiver geometry at a given f-number and incidence angle (also referred to as the tracking error angle). The laws of polychromatic light refraction along with trigonometry and spherical geometry were utilized to optimize the POE grooves, SOE radius, receiver size, and SOE–receiver spacing.
Date: July 8, 2019
Creator: Qandil, Hassan; Wang, Shuping & Zhao, Weihuan
Item Type: Refine your search to only Article
Partner: UNT College of Engineering
open access

Development and Test of High-Temperature Piezoelectric Wafer Active Sensors for Structural Health Monitoring

Description: High-temperature piezoelectric wafer active sensors (HT-PWAS) have been developed for structure health monitoring at hazard environments for decades. Different candidates have previously been tested under 270 °C and a new piezoelectric material langasite (LGS) was chosen here for a pilot study up to 700 °C. A preliminary study was performed to develop a high temperature sensor that utilizes langasite material. The Electromechanical impedance (E/M) method was chosen to detect the piezoelectric p… more
Date: December 2014
Creator: Bao, Yuanye
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Wide Band Frequency-adjustable Piezoelectric Energy Harvester: an Experimental Study

Description: Piezoelectric energy harvester has become a new powering choice for small electronic device. Due to its piezoelectric effect, electric energy can be obtained from ambient vibrations. This thesis is intending to build a frequency-adjustable piezoelectric energy harvester system. The system is structured with two piezoelectric bimorph beams, which are connected to each other by a spring. The feasibility of the frequency-adjustable piezoelectric energy harvester has been proved by investigating ef… more
Date: August 2012
Creator: Lee, Pohua
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Wireless In-home Ecg Monitoring System with Remote Access

Description: The thesis work details the design and testing of a wireless electrocardiogram (ECG) system. This system includes a wireless ECG device, as well as software packages to visually display the waveform locally on a computer and remotely on a web page. The remote viewing capability also extends to using an Android phone application. The purpose of the system is to serve as a means for a doctor or physician to check up on a patient away from a hospital setting. This system allows for a patient to be… more
Date: August 2012
Creator: Porter, Logan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Drive Level Dependence of Advanced Piezoelectric Resonators

Description: Resonators are one of the most important parts of electronic products. They provide a stable reference frequency to ensure the operation of these products. Recently, the electronic products have the trend of miniaturization, which rendered the size reduction of the resonators as well [1]. Better design of the resonators relies on a better understanding of the crystals' nonlinear behavior [2]. The nonlinearities affect the quality factor and acoustic behavior of MEMS (Micro-Electro-Mechanical-Sy… more
Date: August 2012
Creator: Xie, Yuan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Recommended Modified zone Method Correction Factor for Determining R-values of Cold-Formed Steel Wall Assemblies

Description: Currently, ASHRAE has determined the zone method and modified zone method are appropriate calculation methods for materials with a high difference in conductivity, such as cold-formed steel (CFS) walls. Because there is currently no standard U-Factor calculation method for CFS walls, designers and code officials alike tend to resort to the zone method. However, the zone method is restricted to larger span assemblies because the zone factor coefficient is 2.0. This tends to overestimate the amou… more
Date: May 2011
Creator: Black, John
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

The Use of Optical Metrology in Active Positioning of a Lens

Description: Precisely positioned optical lenses are currently required for many highly repetitive mechanics and applications. Thus the need for micron-scale repetition between opto-mechanical units is evident, especially in industrial manufacturing and medical breakthroughs. In this thesis, a novel optical metrology system is proposed, designed, and built whose purpose is to precisely locate the center of a mechanical fixture and then to assemble a plano-convex optical lens into the located position of the… more
Date: August 2014
Creator: Ji, Zheng
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Direct Immersion Cooling Via Nucleate Boiling of HFE-7100 Dielectric Liquid on Hydrophobic and Hydrophilic Surfaces

Description: This study experimentally investigated the effect of hydrophobic and hydrophilic surfaces characteristics on nucleate boiling heat transfer performance for the application of direct immersion cooling of electronics. A dielectric liquid, HFE – 7100 was used as the working fluid in the saturated boiling tests. Twelve types of 1-cm2 copper heater samples, simulating high heat flux components, featured reference smooth copper surface, fully and patterned hydrophobic surface and fully and patterned … more
Date: December 2014
Creator: Joshua, Nihal E.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

The Measurement of the Third-order Elastic Constants for La3ga5sio14 (Lgs) and La3ga55ta05o14 (Lgt) Single Crystal

Description: Recently, the development of electronic technology towards higher frequencies and larger band widths has led to interest in finding new piezoelectric materials, which could be used to make filters with larger pass band widths and oscillators with better frequency stability. Langasite (La3Ga5SiO14, LGS) and its isomorphs have enticed considerable attention of researchers as a potential substrate material for piezoelectric device applications because of its high frequency stability and fairly goo… more
Date: December 2013
Creator: Karim, Md Afzalul
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen