42 Matching Results

Search Results

Results: 1 - 24 next
open access

In-Core Instrumentation Development Program Quarterly Progress Report September - December 1963

Description: Introduction: The objective of Project Agreement 22 is to determine the feasibility of using in-core ion chambers to cover the complete reactor neutron flux startup range from 10(4) -5 - 10(13) nv using in-core ion chambers. The counting mode of operation will be used at low neutron flux levels and the RMS voltage fluctuation mode (Campbell Theorem) will be used at high neutron flux levels. The June-September Progress Report (GEAP-4386) shows how the RMS voltage mode can be used, discusses c… more
Date: January 1964
Creator: DuBridge, R. A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Mechanical, Fluid Flow, and Heat Transfer Out-Of-Pile Tests on EVESR MKI Prototype Fuel Bundle

Description: Summary: An EVESR MKI prototype fuel bundle was fully instrumented and operated intermittently for a 5-month period at the Pacific Gas and Electric Company’s Moss Landing Power Station. The vessel was operated up to 1000 psi with steam flows from 3000 to 26,600 lb/h, and steam inlet temperatures up to 825 degrees F. Data was recorded for blowout, vibration, flow distribution, heat transfer and pressure drop. The mechanical integrity of the fuel bundle, riser, and jumper system was satisfact… more
Date: February 1964
Creator: Polomik, E. E.; Fritz, J. R. & Ianni, P. W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Nuclear Superheat Quarterly Project Report: Eighteenth Quarter, November, 1963-January, 1964

Description: From introduction: "This is the eighteenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."
Date: February 15, 1964
Creator: Flock, W. L. & Imhoff, D. H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Preoperational Power Stability Analysis of the Consumers Big Rock Point Plant

Description: Summary: An analytical study of the stability of the Big Rock Nuclear Reactor has been performed for the plant as built, and supplements a previous design stability study. The plant has been determined by this analysis to be very stable under every mode of operation anticipated during Phase I of the development program testing. Even under conservative assumptions of system parameters the minimum calculated gain and phase margins do not go below 13.0 db and 46 degrees, respectively. (Nor are … more
Date: February 1964
Creator: Case, J. M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

A Program of Two-Phase Flow Investigation Quarterly Report: Fourth Quarterly Report, January-March, 1964

Description: Summary: The design, construction and assembly of all components were completed during the first contract year previous to December 1963. These efforts, defined by Tasks A-F, are document in (1), (2), and (3). Brief summaries of these completed efforts are given in the introduction to each of the tasks in the text of this report. The digest given below covers only the shakedown and analysis work carried out in the fourth quarter of the first contract year. Task G Shakedown Tests. The photo… more
Date: March 16, 1964
Creator: Staub, F. W. & Zuber, N.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Sodium-Cooled Reactors Program, Fast Ceramic Reactor Development Program: Tenth Quarterly Report, January-March 1964

Description: Quarterly report discussing progress on the Fast Ceramic Reactor Development Program. Information is reported on vented fuel production, transient testing of fuel, fuel performance evaluation, fast-flux irradiation of fuel, and reactor physics and core analysis.
Date: April 1964
Creator: Breizy, C. E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Transition and Film Boiling Data at 600, 1000, and 1400 PSIA in Forced Convection Heat Transfer to Water

Description: Summary: Data were obtained in a two-road test section which consisted of two 7/16-inch diameter heater rods inside a roughly rectangular flow area. The heated length of the rods was 30 inches, with a 15-inch unheated calming length preceding it. Heater wall temperatures were recorded while the heater tubes were trans-versing the critical heat flux and transition boiling; these temperatures were used to calculate heat transfer coefficients. The following general results were obtaining: (a)… more
Date: March 1964
Creator: Hench, J. E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Transition Boiling Heat Transfer Program; Fifth Quarterly Progress Report, January - March 1964

Description: Summary: Tests with the two-rod assembly were performed with liquid film trippers attached to the unheated wall, and a variation in rod spacing. Experimental data and improved high-speed motion pictures have been obtained of transition boiling behavior. The changes of the local heat transfer process between nucleate and film boiling can be readily distinguished i the motion pictures. Observational test performed with very short fins on the heated surface resulted in essentially eliminating … more
Date: April 1, 1964
Creator: Quinn, E. P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Transition Boiling Heat Transfer Program; Fourth Quarterly Progress Report, October - December 1963

Description: Summary: Heat transfer tests employing the two-rod test section without film tripping devices have been completed. Representations defining critical heat flux, transition boiling and film boiling behavior at high pressures and over a steam quality range of 25 to 90 percent are shown. Fabrication of a new observational test section was completed and initial test results with high-speed motion pictures were obtained. A test loop instability which was found to affect transition boiling behavio… more
Date: January 1, 1964
Creator: Quinn, E. P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Transition Boiling Heat Transfer Program; Sixth Quarterly Progress Report, April - June 1964

Description: Summary: Transition boiling data was taken with an improved flow loop, to explore the influence of loop characteristics on rod temperature fluctuations the transition region was found to be much smaller than for comparable conditions with a different loop. Also the amplitude, and frequency of the temperature oscillations, were significantly less than before. These results indicate that loop characteristic and flow disturbance parameters play a prominent part in governing the transition tempe… more
Date: July 1, 1964
Creator: Quinn, E. P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Two-Phase Pressure Losses Quarterly Progress Report: Eighth Quarter, November 12, 1963 - February 11, 1964

Description: Technical report describing that voids were measured in a ½-inch by 1-3/4-inch channel with the S-1 insert (B(0)/B(1) = 0.4, L(0) = 0.1 inch), at 2 inches ahead of the insert (position A), ½-inch past the insert (position B), 5 inches past (position C), and 12 inches past (position D). The conditions were: P – 1000 psia, G = 1.00 x 10(6) lb/h-ft(2), and x = 18.8 percent. Average void and void distribution at position A are the same as for flow in a straight channel. Void distribution at posi… more
Date: March 1, 1964
Creator: Janssen, E. (Engineer) & Kervinen, J. A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

High Power Density Development Project: Sixteenth Quarterly Progress Report, January-March 1964

Description: Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development, (2) Task 1B-Fuel Fabrication Development. Assembly, (3) Task II-Stability, Heat Transfer and Fluid Flow, (4) Task III-Physics Development, and (5) Task IV-Co-Ordination and Test Planning.
Date: April 1, 1964
Creator: Holladay, R. L.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

In-Core Instrumentation Development Program Quarterly Progress Report January - March 1964

Description: The objective of Project Agreement 22 is to determine the feasibility of using in-core ion chambers to cover the complete reactor neutron flux startup range from 10(4) -5 - 10(13) nv using in-core ion chambers. This technical report discusses the following topics: low versus high cable termination impedance, amplifier considerations, noise considerations, gas and pressure selection, cable selection, effect of gamma, effect of temperature, and remaining problems.
Date: April 1964
Creator: DuBridge, R. A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Sodium-Cooled Reactors Program, Fast Ceramic Reactor Development Program: Ninth Quarterly Report, October-December 1963

Description: Quarterly report discussing progress on the Fast Ceramic Reactor Development Program. Information is reported on vented fuel production, fuel testing in TREAT, fuel performance evaluation, fast-flux irradiation of fuel, and reactor dynamics and design.
Date: January 1964
Creator: Leitz, F. J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Reactor Pressure Vessel Material Surveillance Program at the Garigliano Nuclear Power Plant

Description: Abstract: A materials exposure program has been established in the Garigliano Nuclear Power Plant to measure the effect of neutron irradiation and time at temperate on the mechanical properties of the reactor pressure vessel steel. Base metal specimens were made from portions of the pressure vessel steel, and weld heat-affected zone and weld metal samples were taken from a weldment made from the pressure vessel steel and simulating a pressure vessel circumferential weld since there are no longi… more
Date: March 1964
Creator: Brandt, F. A. & Kobsa, I. R.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Sodium Mass Transfer. [Part] XI. 1963 Test Run Reports (January - June)

Description: Technical report describing how corrosion data and exposure effects were obtained by subjecting metallic samples, during programmed test runs to flowing sodium in 6 test loops fabricated with various combinations of three selected materials, Type 316 stainless steel, 2 1/4 Cr-1 Mo alloy steel, and 5 Cr-1/2 Mo-1/2 Ti alloy steel. Information produced by each test run, including operational and metallurgical data and analyses, is presented. Data are shown in tables, graphs, and drawings.
Date: February 1964
Creator: Lockhart, R. W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Sodium Mass Transfer. [Part] 8. Corrosion of Stainless Steel in Isothermal Regions of a Flowing Sodium System

Description: Technical report describing an analytical investigation made on the mechanism of the "downstream" effect in the corrosion of stainless steel in sodium. A mechanism of iron alloy corrosion is assumed in which the controlling rate is diffusion of iron-oxygen species, probably a FeO-Na2O complex. A mathematical model is developed for the corrosion, and the predicted results agree with the experimental data. The corroding species is probably present in sodium at concentrations of ~10(-8) g Fe/g Na. more
Date: February 1964
Creator: Mottley, J. D. & Epstein, Leo F.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Design and Fabrication of Pellet Fuel Rods Clad With Thin Wall Stainless Steel

Description: Summary: Stainless steel clad nuclear fuel cycle costs can be reduced to those associated with Zircaloy clad fuel or potentially lower by reducing the thickness of the clad tube wall until performance penalties offset the savings associated with the reduction in parasitic neutron absorption. To demonstrate the feasibility and investigate performance capabilities of thin clad fuel rods for power reactor application an assembly was fabricated with 0.0127 cm (5 mil) thick stainless steel cladding … more
Date: February 1964
Creator: Hoffmann, J. P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

UO2 Pellet Thermal Conductivity From Irradiations With Central Melting

Description: Abstract: Continued irradiation experience under the AEC - Euratom, UO2 High Performance Program provided five separate and distinct sets of data on UO2 thermal conductivity. Four of these results are expressed in terms of the value of the thermal conductivity. The first two of these measurements were applicable -- strictly -- to poly crystalline UO2. Recently, three additional sets of measurements have been obtained -- all pertinent to UO2 after the formation of large columnar grains. The … more
Date: July 1964
Creator: Lyons, M. F.; Coplin, D. H.; Pashos, T. J. & Weidenbaum, B.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Design and Fabrication of Fuel Rods Containing Sintered UO2 Extrusions - Assembly 11L

Description: The extrusion forming of ceramic powders may be economically interesting in the field of nuclear fuel fabrication. When applied to the forming of rod-type uranium dioxide fuel, extrusion processes have been able to produce cylindrical bodies with length-to-diameter ratios much greater than those of the conventional die-pressed pellets. Furthermore, after being sintered, the extrusions have exhibited densities at least as high as those of sintered pellets. Thus, extrusion forming may offer re… more
Date: February 1964
Creator: Megerth, F. H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
Back to Top of Screen