UNT Libraries - 24 Matching Results

Search Results

prev Results: 11 - 24
open access

Influence of design and coatings on the mechanical reliability of semiconductor wafers.

Description: We investigate some of the mechanical design factors of wafers and the effect on strength. Thin, solid, pre-stressed films are proposed as a means to improve the bulk mechanical properties of a wafer. Three-point bending was used to evaluate the laser scribe density and chemical processing effect on wafer strength. Drop and strike tests were employed to investigate the edge bevel profile effect on the mechanical properties of the wafer. To characterize the effect of thin films on stren… more
Date: August 2002
Creator: Yoder, Karl J.
Item Type: Refine your search to only Thesis or Dissertation

Mechanical Properties of Polymer Modified Mortar

Description: The mechanical properties of the polymer-modified mortar are markedly improved over conventional cement mortar. We utilized recycled ABS in powder form and a polymer latex emulsion, polymer percentage ranges from 0 to 25 percent by polymer/cement ratio were investigated. The mechanical properties investigated were compression strength and adhesion strength. Compression strength effects did not have an impact on adhesion strength. Adhesion strength was calculated with pullout testing apparatus … more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: August 2002
Creator: Palos, Artemio
Item Type: Refine your search to only Thesis or Dissertation

Application of Thermomechanical Characterization Techniques to Bismuth Telluride Based Thermoelectric Materials

Description: The thermoelectric properties of bismuth telluride based thermoelectric (TE) materials are well-characterized, but comparatively little has been published on the thermomechanical properties. In this paper, dynamic mechanical analysis (DMA) and differential scanning calorimetry data for bismuth telluride based TE materials is presented. The TE materials' tan delta values, indicative of viscoelastic energy dissipation modes, approached that of glassy or crystalline polymers, were greater than ten… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: August 2002
Creator: White, John B.
Item Type: Refine your search to only Thesis or Dissertation
open access

Stability of Field Emitter Arrays to Oxygen Exposures

Description: The purpose of these experiments was to determine the degradation mechanisms of molybdenum based field emitter arrays to oxygen exposures and to improve the overall reliability. In addition, we also evaluated the emission current stability of gold-coated field emitter arrays to oxygen exposures. oxygen at 1x10-6 torr was introduced into the chamber through a leak valve for different lengths of time and duty cycles. To ensure identical oxygen exposure and experimental measurement conditions, ti… more
Date: December 2002
Creator: Godbole, Soumitra Kumar
Item Type: Refine your search to only Thesis or Dissertation
open access

The Electron Emission Characteristics of Aluminum, Molybdenum and Carbon Nanotubes Studied by Field Emission and Photoemission.

Description: The electron emission characteristics of aluminum, molybdenum and carbon nanotubes were studied. The experiments were setup to study the emission behavior as a function of temperature and exposure to oxygen. Changes in the surface work function as a result of thermal annealing were monitored with low energy ultra-violet photoelectron spectroscopy for flat samples while field emission energy distributions were used on tip samples. The change in the field emission from fabricated single tips expo… more
Date: December 2002
Creator: Sosa, Edward Delarosa
Item Type: Refine your search to only Thesis or Dissertation
open access

Characterization and Mechanical Properties of Nanoscale Precipitates in Modified Al-Si-Cu Alloys Using Transmission Electron Microscopy and 3D Atom Probe Tomography.

Description: Among the commercial aluminum alloys, aluminum 319 (Al-7wt%Si-4wt%Cu) type alloys are popularly used in automobile engine parts. These alloys have good casting characteristics and excellent mechanical properties resulting from a suitable heat treatment. To get a high strength in the 319 type alloys, grain refining, reducing the porosity, solid solution hardening, and precipitation hardening are preferred. All experimental variables such as solidification condition, composition, and heat treatme… more
Date: May 2007
Creator: Hwang, Junyeon
Item Type: Refine your search to only Thesis or Dissertation
open access

Formation and Quantification of Corrosion Deposits in the Power Industry

Description: The presence of deposits on the secondary side of pressurized water reactor (PWR) steam generator systems is one of the main contributors to the high maintenance costs of these generators. Formation and transport of corrosion products formed due to the presence of impurities, metals and metallic oxides in the secondary side of the steam generator units result in formation of deposits. This research deals with understanding the deposit formation and characterization of deposits by studying the s… more
Date: May 2007
Creator: Namduri, Haritha
Item Type: Refine your search to only Thesis or Dissertation
open access

Structure property and deformation analysis of polypropylene montmorillonite nanocomposites.

Description: Nanocomposites with expandable smectites such as montmorillonite layered silicates (MLS) in polymer matrices have attracted extensive application interest. Numerous MLS concentrations have been used with no particular justification. Here, we investigate the effects of MLS dispersion within the matrix and on mechanical performance. The latter is resolved through a three-prong investigation on rate dependent tensile results, time dependent creep results and the influence of a sharp notch in polyp… more
Date: May 2003
Creator: Hernandez-Luna, Alejandro
Item Type: Refine your search to only Thesis or Dissertation

Characterization of Methyltrimethoxysilane Sol-Gel Polymerization and the Resulting Aerogels.

Description: Methyl-functionalized porous silica is of considerable interest as a low dielectric constant film for semiconductor devices. The structural development of these materials appears to affect their gelation behaviors and impact their mechanical properties and shrinkage during processing. 29Si solution NMR was used to follow the structural evolution of MTMS (methyltrimethoxysilane) polymerization to gelation or precipitation, and thus to better understand the species that affect these properties an… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: August 2003
Creator: Dong, Hanjiang
Item Type: Refine your search to only Thesis or Dissertation

Mechanical behavior and performance of injection molded semi-crystalline polymers.

Description: I have used computer simulations to investigate the behavior of polymeric materials at the molecular level. The simulations were performed using the molecular dynamics method with Lennard-Jones potentials defining the interactions between particles in the system. Significant effort was put into the creation of realistic materials on the computer. For this purpose, an algorithm was developed based on the step-wise polymerization process. The resulting computer-generated materials (CGMs) exhibit… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: August 2003
Creator: Simoes, Ricardo J. F.
Item Type: Refine your search to only Thesis or Dissertation

Materials properties of ruthenium and ruthenium oxides thin films for advanced electronic applications.

Description: Ruthenium and ruthenium dioxide thin films have shown great promise in various applications, such as thick film resistors, buffer layers for yttrium barium copper oxide (YBCO) superconducting thin films, and as electrodes in ferroelectric memories. Other potential applications in Si based complementary metal oxide semiconductor (CMOS) devices are currently being studied. The search for alternative metal-based gate electrodes as a replacement of poly-Si gates has intensified during the last few … more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2006
Creator: Lim, ChangDuk
Item Type: Refine your search to only Thesis or Dissertation
open access

Analysis of Thermoplastic Polyimide + Polymer Liquid Crystal Blends

Description: Thermoplastic polyimides (TPIs) exhibit high glass transition temperatures (Tgs), which make them useful in high performance applications. Amorphous and semicrystalline TPIs show sub-Tg relaxations, which can aid in improving strength characteristics through energy absorption. The a relaxation of both types of TPIs indicates a cooperative nature. The semicrystalline TPI shows thermo-irreversible cold crystallization phenomenon. The polymer liquid crystal (PLC) used in the blends is thermotropic… more
Date: May 1998
Creator: Gopalanarayanan, Bhaskar
Item Type: Refine your search to only Thesis or Dissertation
open access

Analyses of Particulate Contaminants in Semiconductor Processing Fluids

Description: Particle contamination control is a critical issue for the semiconductor industry. In the near future, this industry will be concerned with the chemical identities of contaminant particles as small as 0.01 pm in size. Therefore, analytical techniques with both high chemical sensitivity and spatial resolution are required. Transmission electron microscopy (TEM) provides excellent spatial resolution and yields structural and compositional information. It is rarely used, however, due to the diffic… more
Date: August 1998
Creator: Xu, Daxue
Item Type: Refine your search to only Thesis or Dissertation
open access

Comparative Coarsening Kinetics of Gamma Prime Precipitates in Nickel and Cobalt Base Superalloys

Description: The increasing technological need to push service conditions of structural materials to higher temperatures has motivated the development of several alloy systems. Among them, superalloys are an excellent candidate for high temperature applications because of their ability to form coherent ordered precipitates, which enable the retention of high strength close to their melting temperature. The accelerated kinetics of solute diffusion, with or without an added component of mechanical stress, le… more
Date: August 2014
Creator: Meher, Subhashish
Item Type: Refine your search to only Thesis or Dissertation
Back to Top of Screen