UNT Theses and Dissertations - 62 Matching Results

Search Results

prev Results: 25 - 48 next
open access

Fabrication and Testing of Biomimetic Microstructures for Walkway Tribometers

Description: The main objective of this work is to give contribution in both additive manufacturing (AM) and tribometry derived from the application and study of materials available with the use of biomimetic designs. Additional contributions are determining what effects treatments for flooring surfaces may have on the dynamic coefficient of friction and the effects of these products on common surfaces. The validity of the proposed methodology for a proof of concept was demonstrated by comparing measured dy… more
Date: December 2019
Creator: Haney, Christopher Willard
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Study of the Synthesis and Surface Modification of UV Emitting Zinc Oxide for Bio-Medical Applications

Description: This thesis presents a novel ZnO-hydrogel based fluorescent colloidal semiconductor nanomaterial system for potential bio-medical applications such as bio-imaging, cancer detection and therapy. The preparation of ZnO nanoparticles and their surface modification to make a biocompatible material with enhanced optical properties is discussed. High quality ZnO nanoparticles with UV band edge emission are prepared using gas evaporation method. Semiconductor materials including ZnO are insoluble in w… more
Date: May 2009
Creator: John, Sween
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Study on the System Reliability of Cold-Formed Steel Roof Trusses

Description: This thesis presents a research project aimed at advancing the treatment of cold-formed steel (CFS) structural reliability in roof trusses. Structural design today relies almost exclusively on component-level design, so structural safety is assured by limiting the probability of failure of individual components. Reliability of the entire system is typically not assessed, so in a worst-case scenario the system reliability may be less than the component reliability, or in a best-case scenario the… more
Date: May 2017
Creator: Johnson, Adam M.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Seismic Performance Evaluation of Novel Cold-Formed Steel Framed Shear Walls Sheathed with Corrugated Steel Sheets

Description: This thesis presents experiments and numerical analysis of a novel cold-formed steel framed shear wall sheathed with corrugated steel sheets. The objective of this newly designed shear wall is to meet the growing demand of mid-rise buildings and the combustibility requirement in the International Building Code. The strength of the novel shear wall is higher than currently code certified shear wall in AISI S400-15 so that it could be more favorable for mid-rise building in areas that are prone t… more
Date: August 2017
Creator: Lan, Xing
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Cold-Formed Steel Member Connections Using BAC Screw Fasteners

Description: In this project, the main research objective is intend to seek criteria for evaluating the capacity of BAC screw fasteners with mixed configuration of waterproof seal washer, sealer tape and different pre-drill holes to determine shear and tension strength values for the screws used in cold-formed steel connections. The thesis presents the design methods and test program conducted to investigate the behavior and strength of the screw connections in shear and tension test. Test results were comp… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2019
Creator: Li, Xun
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Development of a Hybrid Molecular Ultraviolet Photodetector based on Guanosine Derivatives

Description: Modern studies on charge transfer reaction and conductivity measurements of DNA have shown that the electrical behavior of DNA ranges from that of an insulator to that of a wide bandgap semiconductor. Based on this property of DNA, a metal-semiconductor-metal photodetector is fabricated using a self-assembled layer of deoxyguanosine derivative (DNA base) deposited between gold electrodes. The electrodes are lithographically designed on a GaN substrate separated by a distance L (50nm < L < 100nm… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: December 2005
Creator: Liddar, Harsheetal
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Data Acquisition System Experiment for Gas Temperature and Pressure Measurements on a Liquid-Nitrogen-Powered Vehicle

Description: A data acquisition system was set up to measure gas temperatures and pressures at various points on a liquid-nitrogen-powered vehicle. The experiment was attempted to develop a data acquisition method for applications on engines that use liquid air as the fuel. Two thermocouples and a pressure transducer were connected using data acquisition instruments interfaced to a laptop computer to acquire data.
Date: May 1998
Creator: Lui, Samson Sze-Sang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Characterization of Boron Nitride Thin Films on Silicon (100) Wafer.

Description: Cubic boron nitride (cBN) thin films offer attractive mechanical and electrical properties. The synthesis of cBN films have been deposited using both physical and chemical vapor deposition methods, which generate internal residual, stresses that result in delamination of the film from substrates. Boron nitride films were deposited using electron beam evaporation without bias voltage and nitrogen bombardment (to reduce stresses) were characterize using FTIR, XRD, SEM, EDS, TEM, and AFM technique… more
Date: August 2007
Creator: Maranon, Walter
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of the feasibility of non-invasive carbon dioxide detection using spectroscopy in the visible spectrum.

Description: Pulse oximeters are used in operating rooms and recovery rooms as a monitoring device for oxygen in the respiratory system of the patient. The advantage of pulse oximeters over other methods of oxygen monitoring is that they are easy to use and they are non-invasive, which means it is not necessary break the skin to extract blood for information to be obtained. The standard for the measurement of partial pressure of CO2 and O2 is an arterial blood gas analysis (ABG). However routine monitoring … more
Date: December 2007
Creator: Marks, Damian
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Development of a Simplified Fracture Toughness Tool for Polymers

Description: This thesis presents research toward the development of a simple inexpensive fracture toughness tool for polymeric materials. Experiments were conducted to test the specimen configuration and the fracture toughness tool against an established ASTM standard for polymer fracture toughness, D5045, and a commonly used four-point bend method. The materials used in this study were polycarbonate and high density polyethylene. Reductions in both the production time and the variability resulting from th… more
Date: August 1997
Creator: Marnock, Patrick J. (Patrick Joseph)
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of Immersion Cooled ARM-Based Computer Clusters for Low-Cost, High-Performance Computing

Description: This study aimed to investigate performance of ARM-based computer clusters using two-phase immersion cooling approach, and demonstrate its potential benefits over the air-based natural and forced convection approaches. ARM-based clusters were created using Raspberry Pi model 2 and 3, a commodity-level, single-board computer. Immersion cooling mode utilized two types of dielectric liquids, HFE-7000 and HFE-7100. Experiments involved running benchmarking tests Sysbench high performance linpack (H… more
Date: August 2017
Creator: Mohammed, Awaizulla Shareef
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Laser Cutting Machine: Justification of initial costs

Description: The Industrial Laser is firmly established in metalcutting as the tool of choice for many applications. The elevator division of Montgomery KONE Inc., in an effort to move towards quality, ontime, complete deliveries and 100% customer satisfaction, decided to invest in new equipment to improve manufacturing processes. A huge investment is proposed for a laser-cutting machine. It is the responsibility of Manufacturing Engineering to direct the management by justifying its benefits, which include… more
Date: May 2001
Creator: Nagaraja, Dwarakish
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Design of Power Amplifier Test Signals with a User-Defined Multisine

Description: Cellular radio communication involves wireless transmission and reception of signals at radio frequencies (RF). Base stations house equipment critical to the transmission and reception of signals. Power amplifier (PA) is a crucial element in base station assembly. PAs are expensive, take up space and dissipate heat. Of all the elements in the base station, it is difficult to design and operate a power amplifier. New designs of power amplifiers are constantly tested. One of the most important co… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Nagarajan, Preeti
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Flow Accelerated Corrosion Experience at Comanche Peak Steam Electric Station

Description: Flow accelerated corrosion (FAC) is a major concern in the power industry as it causes thinning of the pipes by the dissolution of the passive oxide layer formed on the pipe surface. Present research deals with comparing the protection offered by the magnetite (Fe3O4) versus maghemite (γ-Fe2O3) phases thickness loss measurements. Fourier transform infrared spectroscopy (FTIR) is used in distinguishing these two elusive phases of iron oxides. Representative pipes are collected from high pressure… more
Date: May 2008
Creator: Nakka, Ravi Kumar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Characterization of Iron Oxide Deposits Formed at Comanche Peak Steam Electric Station

Description: The presence of deposits leading to corrosion of the steam generator (SG) systems is a major contributor to operation and maintenance cost of pressurized water reactor (PWR) plants. Formation and transport of corrosion products formed due to the presence of impurities, metallic oxides and cations in the secondary side of the SG units result in formation of deposits. This research deals with the characterization of deposit samples collected from the two SG units (unit 1 and unit 2) at Comanche P… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2003
Creator: Namduri, Haritha
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Liquid Nitrogen Propulsion Systems for Automotive Applications: Calculation of Mechanical Efficiency of a Dual, Double-acting Piston Propulsion System

Description: A dual, double-acting propulsion system is analyzed to determine how efficiently it can convert the potential energy available from liquid nitrogen into useful work. The two double-acting pistons (high- and low-pressure) were analyzed by using a Matlab-Simulink computer simulation to determine their respective mechanical efficiencies. The flow circuit for the entire system was analyzed by using flow circuit analysis software to determine pressure losses throughout the system at the required mas… more
Date: May 2008
Creator: North, Thomas B.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Effects of Thickness and Indenter Tip Geometry in Nanoindentation of Nickel Films

Description: Nanoindentation has become a widely used technique to measure the mechanical properties of materials. Due to its capability to deform materials in micro- and nano-scale, nanoindentation has found more applications in characterizing the deformation behavior and determining the mechanical properties of thin films and coatings. This research deals with the characterization of samples received from Center for Advanced Microstructures and Devices (CAMD) and Integran Technologies Inc., Toronto, Canad… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Parakala, Padma
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Topology and Lattice-Based Structural Design Optimization for Additively Manufactured Medical Implants

Description: Topology-based optimization techniques and lattice structures are powerful ways to accomplish lightweight components with enhanced mechanical performance. Recent developments in additive manufacturing (AM) have led the way to extraordinary opportunities in realizing complex designs that are derived from topology and lattice-based structural optimization. The main aim of this work is to give a contribution, in the integration between structural optimization techniques and AM, by proposing a setu… more
Date: May 2019
Creator: Peto, Marinela
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Effect of Engineered Surfaces on Valve Performance

Description: Performance of air operated valves is a major maintenance concern in process industries. Anecdotal information indicates that reliability of some high maintenance valves has been improved by using an ion deposition process to achieve engineered surfaces on selected components. This project compared friction for various surface treatments of selected valve components. Results indicate valve performance may be slightly more consistent when an engineered surface is applied in the valve packing are… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2000
Creator: Pope, Larry G.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

FEM of nanoindentation on micro- and nanocrystalline Ni: Analysis of factors affecting hardness and modulus values.

Description: Nanoindentation is a widely used technique to measure the mechanical properties of films with thickness ranging from nanometers to micrometers. A much better understanding of the contact mechanics is obtained mostly through finite element modeling. The experiments were modeled using the software package Nano SP1 that is based on COSMOSM™ (Structural Research & Analysis Corp, www.cosmosm.com), a finite element code. The fundamental material properties affecting pile-up are the ratio of the effec… more
Date: August 2005
Creator: Pothapragada, Raja Mahesh
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Nodal Resistance Measurement System

Description: The latest development in the measurement techniques has resulted in fast improvements in the instruments used for measurement of various electrical quantities. A common problem in such instruments is the automation of acquiring, retrieving and controlling the measurements by a computer or a laptop. In this study, nodal resistance measurement (NRM) system is developed to solve the above problem. The purpose of this study is to design and develop a compact electronic board, which measures elect… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2005
Creator: Putta, Sunil Kumar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Modeling and Analysis of Prototype Shelter Structure on Abaqus

Description: Due to the constraint of high costs and limitations of load conditions, experimental testing is not appropriate for the static study of shelter structures. Comparatively, an effective computational modeling and numerical solution demonstrates significant advantages for understanding the response of steel shelter structures. This study gives an insight into the structural integrity of the prototype shelter structure which is examined using computer simulation of the shelter structure on Abaqus/C… more
Date: August 2020
Creator: Rao, Noraiz
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Structural, Thermal, and Corrosion Properties of a Cold-Formed Steel Rigid Wall Relocatable Shelter

Description: A prototype rigid wall relocatable shelter was designed and constructed using cold-formed steel (CFS) construction techniques including shear walls with corrugated sheathings. The design of the shelter was to be mechanically sound with adequate thermal performance and resistance to corrosion. Modeling of structural shear walls was performed using ABAQUS and verified with experimental results. At the project's conclusion, a completed full-scale prototype shelter was constructed.
Date: May 2020
Creator: Rowen, Alexander David
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen