12 Matching Results

Search Results

Advanced search parameters have been applied.
in subjects: "aircraft design"  
Results: 1 - 12
open access

The Latécoère 521 "Lieutenant De Vaisseau Paris" Commercial Flying Boat (French): A Two-Deck Six-Engine Semicantilever Sesquiplane

Description: Circular presenting a description of the Latécoère 521, which was the largest aircraft built in France at the time. A more detailed description of the wings, hull, accommodation for passengers and officers, fuel system, controls, and flight characteristics is provided.
Date: March 1936
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The Avro "Anson" General-Purpose Airplane (British): A Two-Engine Low-Wing Cantilever Monoplane

Description: Circular describing the Avro Anson, which is a two-engine low-wing cantilever monoplane of the general-purpose type. Details regarding the wing, landing gear, controls, fuselage, pilot's equipment, power plant, armament, characteristics, performance, drawings, and photographs are provided.
Date: March 1936
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The Vickers-Supermarine "Scapa" (British): A Military Flying Boat

Description: Circular describing the Vickers-Supermarine Scapa, which is a military flying boat which was designed to be used for observation, bombing, torpedo transport, and training and navigational instruction. Details of the aerodynamic design, structural features, engine installation, characteristics, drawings, and photographs are provided.
Date: May 1936
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

Description: From Summary: "The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and h… more
Date: January 1936
Creator: Dawson, John R.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Estimation of moments of inertia of airplanes from design data

Description: "A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can… more
Date: July 1936
Creator: Kirschbaum, H. W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

An Approximate Spin Design Criterion for Monoplanes

Description: "An approximate empirical criterion, based on the projected side area and the mass distribution of the airplane, was formulated. The British results were analyzed and applied to American designs. A simpler design criterion, based solely on the type and the dimensions of the tail, was developed; it is useful in a rapid estimation of whether a new design is likely to comply with the minimum requirements for safety in spinning" (p. 1).
Date: June 1936
Creator: Seidman, Oscar & Donlan, Charles J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Experimental Studies of the Effective Width of Buckled Sheets

Description: The object of the present experiments is a more exact determination of the effective width for the case of pure compression and of the sheet clamped at the angle section. From the experimental data of the effective width the calculation of the buckling load of an angle joined to a thin sheet is then deduced. The test material consisted of spring-hardened brass sheet.
Date: December 1936
Creator: Lahde, R. & Wagner, H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The stress criterion of a tension member with graded flexural stiffness: contribution to the problem of "clamping effect" outside of the elastic range

Description: The approximate size of the stress criterion of a bar on two supports stressed beyond the elastic range is assessed by an approximation. The calculation proceeds from the premise of "substitute flexural stiffness" so defined that the part stressed beyond the elastic range may be considered as following Hooke's law when determining the flexural deformation quantities. For the determination of the substitute flexural stiffness, it is presumed that the material is already stressed so much beyond t… more
Date: September 1936
Creator: Kaul, Hans W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Methods and Formulas for Calculating the Strength of Plate and Shell Constructions as Used in Airplane Design

Description: "This report is a compilation of previously published articles on formulas and methods of calculation for the determination of the strength and stability of plate and shell construction as employed in airplane design. In particular, it treats the problem of isotropic, orthotopic, and stiffened rectangular plates, thin curved panels, and circular cylinders under various loading conditions. The purpose of appending the pertinent literature references following the subjects discussed was to facili… more
Date: February 1936
Creator: Heck, O. S. & Ebner, H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Relative Efficiencies and Design Charts for Various Engine-Propeller Combinations, Special Report

Description: "The relative efficiencies of various engine-propeller combinations were the subject of a study that covered the important flight conditions, particularly the take-off. Design charts that graphically correlate the various propeller parameters were prepared to facilitate the solution of problems and also to clarify the conception of the relationships of the various engine-propeller design factors. It is shown that, among the many methods for improving the take-off thrust, the use of high-pitch, … more
Date: September 1936
Creator: Biermann, David
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Wing-nacelle-propeller interference for wings of various spans force and pressure-distribution tests

Description: Report presents the results of an experimental investigation made in the NACA full-scale wind tunnel to determine the effect of wing span on nacelle-propeller characteristics and, reciprocally, the lateral extent of nacelle and propeller influence on a monoplane wing. The results provide a check on the validity of the previous research on nacelles and propellers with 15-foot-span wings tested in the 20-foot wind tunnel and reported in technical reports 415, 462, 505, 506, and 507.
Date: April 21, 1936
Creator: Robinson, Russell G. & Herrnstein, William H., Jr.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
Back to Top of Screen