From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."
Report presenting measurements of a Consolidated B-24D airplane of accelerations at various points on the wing during landing impacts. landings were made with the wheels initially stationary but free to rotate, with the brakes set before contact, and with the main wheels rotating prior to contact.
Report presenting tests made in the LMAL 16-foot high-speed tunnel to determine the aerodynamic characteristics of a 1000-pound AN-M-65-AZON radio-controlled bomb at a Mach number range of 0.2 to 0.6. Over the Mach number range, the hinge-moment coefficients, yawing-moment coefficients, and lateral-force coefficients exhibited no important changes with increasing speed.
Report presenting testing in the two-dimensional low-turbulence tunnels on a 24-inch-chord model of the NACA 66(215)-116 a = 0.6 airfoil with a 0.25-chord slotted flap. The optimum flap pivot positions were found for three different conditions. The conditions were determined from a consideration of the landing, take-off, and strafing requirements of the airplane.
Report presenting 10 practical-construction models of sections of helicopter rotor blades tested in the NACA two-dimensional low-turbulence pressure tunnel at atmospheric pressure. Lift, drag, and pitching-moment characteristics of blades representing the present method of construction of the YR-4A helicopter were determined.
Report presenting an analysis of data on fuel-vapor loss from fuel tanks during simulated flight obtained by six laboratories to show the effects of individual variables such as altitude, initial fuel temperature, rate of climb, booster-pump agitation, fuel depth, fuel-surface area, types of fuel, and vent-line pressure drop on fuel-vapor loss.
Report discusses an investigation into the behavior of a cantilever beam in transverse motion with a mass at its tip when the root is suddenly brought to rest. Equations for determining the stresses, deflections, and accelerations that arise in the beam are also provided. This testing can be applied to the shock created in an airplane when landing and the vibrations that result.
Report presents a series of charts used to demonstrate typical good and undesirable airplane characteristics as determined in flight that were used to facilitate discussion at a series of conferences between the National Advisory Committee, Army, Navy, and representatives of the aircraft industry. For each chart, the purpose of the test, the flight technique used, the items recorded, and the evaluation and interpretation of the data obtained were provided. Additional figures drawn on the board during the conferences are not reproduced in the report.
From Summary: "Compression tests were made of two groups of panel specimens with hat-section stiffeners. The groups were identical except that the flat sheet of one group was Alclad 24S-T81 and of the other Alclad 24S-T86. Results of the tests are given in tables or charts which show the average stress at which the sheet buckles and the average stress at the maximum load."
Report presenting testing to determine which of three spinner-diffuser designs on an NACA cowling was the most effective in cooling a Pratt & Whitney R-2800 engine installation. The results of pressure-distribution studies in front of and behind each bank of cylinders are presented for a wide range of propeller-operating conditions.
Report presenting results of compression tests of six paper-base plastic panels with outward-acting normal pressure. All panels failed by separation of the skin, either from the rib or from the stiffeners. Results regarding the introduction of air pressure and types of failures encountered are provided.
"Compression tests were made of 63 panels stiffened with corrugated sheet. The specimens were constructed from artificially aged alclad 24S-T aluminum alloy with minimum guaranteed yield strengths of 57 and 48 kips per square inch for the flat- and corrugated-sheet materials, respectively. Results of the tests are presented in charts which show the average stresses at the maximum load and at buckling of the sheet" (p. 1).
Report presenting an investigation of the cooling of a Franklin 6-AC-29S horizontally opposed cylinder air-cooled engine installed in a Fleetwings model 33 trainer. The cowling on the airplane did not provide satisfactory cooling, but several alterations were tested, including with cylinder baffles. Results regarding engine cooling, aerodynamics of the cowling installation, and predicted versus actual cowling performance are provided.
Testing of a dynamically similar model of an Army A-20A airplane to determine the best way to land the airplane in calm and rough water and to determine its probable ditching performance. Results regarding the effect of speed and attitude, effect of flap setting, effect of wind and seaway, effect of simulated damage, effect of sinking speed, effect of propellers, effect of gun blisters, and effect of weight are provided.
Report presenting testing to determine the best way to land the B-25 airplane in calm and rough water and to determine its probable ditching performance. By landing with flaps down in a tail-down attitude at as slow a speed as possible, smooth straight landing runs will probably result in calm water. Results regarding the effect of attitude, effect of flap setting, effect of simulated damage, effect of propellers, and effect of seaway are provided.
Report presenting tests made with a dynamic model of the Army B-26 airplane to determine its behavior when landed on water. Results regarding the general behavior, effect of flaps, effect of landing attitude and speed, tests with undamaged model, tests with simulated damage, tests with propellers, vertical decelerations, and effect of weight are provided.
Report presenting drag measurements in the two-dimensional low-turbulence tunnel of an available 100-inch-chord model of the NACA 23016 wing section. Results regarding the curves of section drag coefficient plotted against Reynolds number for various surface conditions and lift coefficients, variation of drag coefficient with lift coefficient, and effects of skin friction are provided.
Report presenting an investigation conducted with the propeller cuffs and spinner removed to determine their effect in flight on the pressure recovery of the cooling-air flow. Curves are presented to compare the pressure and temperature distribution over the front row of cylinders for flights with and without cuffs and spinner.
Report discussing the knock-limited performance of blends of triptane and 28-R fuel in an F-4 engine at three sets of conditions and three compression ratios. The knock limits of the triptane blends were more sensitive to compression ratio than the 28-R fuel, and the sensitivities of the blends increased as the severity of other engine conditions increased.
Report presenting an investigation conducted to determine the effect of water injection on the knock-limited performance of a V-type 12-cylinder liquid-cooled engine. The knock-limited performance tests were made at an engine speed of 3000 rpm with carburetor-air temperatures of 158, 101, and 50 degrees Fahrenheit at water-fuel ratios of 0, 0.2, 0.4, and 0.6.
Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.
Report discussing the results of using an enlarged vertical tail on a P-63A-1 on directional stability. The tests included measurements of the amount of sideslip at various speeds and normal accelerations. Potential required modifications for increased performance using the larger tail are also described.
Report discussing testing on triptane, hot-acid octane, diisopropyl, neohexane, mixed xylenes, cumene, benzene, toluene, and methyl tert-butyl ether in several blends to determine their knock-limited performance data in F-3 and F-4 engines at standard operating conditions. All of the blending agents examined were found to be usable, with concentrations varying depending on various thermodynamic properties.
Report discussing the cooling characteristics of a 14-cylinder double-row radial air-cooled engine in a four-engine airplane. The effects of charge-air flow, cooling-air pressure drop, and fuel-air ratio on the cooling characteristics were measured separately. The cooling equation, rear middle-barrel temperature, cooling-limited manifold pressure, and maximum cruising power versus temperature-limited power are described.
Report discussing a comparison of the antiknock characteristics of triptane with a temperature-sensitive blending agent and of the fuel knock limits with engine cooling limits. Estimates were also made of temperature-limited engine performance at several flight and engine conditions.
Report presenting flight measurements of the pressures on the horizontal tail surfaces of a typical propeller-driven pursuit airplane during stalled pull-outs at high Mach number. Unit loads measured on the stabilizer at safe maneuvering limits were not only considerably in excess of the design unit loads, but also occurred in a direction opposite to the design loads. Revision of the tail-load design requirements and manner of specifying safe maneuverability limits to pilots appears necessary.
Report presenting flight tests to determine the longitudinal stability characteristics of a pursuit airplane when flown with and without an experimental bellows-type bob weight. When the weight was installed, the stick-free static stability remained approximately constant irrespective of the shift in center of gravity resulting from a change in fuel quantity in the auxiliary fuselage fuel tank. Although the weight functioned satisfactorily, the performance could have been enhanced by the reduction of the friction in the mechanism.
Report discussing testing to check the improvement of 3 or 4 miles per hour in the maximum speed of the P-51B airplane as a result of sealing the wing-gun access doors and flap-spar lightening holes. Large variations in speed were observed during testing, so additional testing and analysis was carried out to determine the effects of various factors that were suspected of contributing to the inconsistency of the plane's performance.
Report presenting a series of tests on the Brewster XSBA-1 airplane to determine the effects of various tail modifications. Some of the modifications include variations of the chord of the elevator and rudder while the span and total area of the surfaces are kept constant and variations of the total area of the vertical tail surface. Results regarding the longitudinal stability and control and lateral stability and control are provided.
"Tests were conducted to determine the effect of several flight variables and several types of fuel agitation on fuel-vapor loss from a fuel tank during flight. Data were obtained from simulated-flight tests, in which the effects of rate of climb, altitude, initial fuel temperature, weathering of fuel, and fuel agitation were investigated; and a correlation between the simulated-flight and actual-flight data was established" (p. 1).
From Summary: "Tests on the B-34 fin-rudder-tab assembly were performed in the NACA 8-foot high-speed tunnel. Two cases of tab flutter were studied. It was shown conclusively that the frequency of the original or heavy tab was too low and caused coupling with one of the lower bending frequencies. A general conclusion was made that the tab frequency should be considerably higher than the lower modes of the fin-rudder assembly because there is generally a weaker coupling between the tab and the higher mode responses."
Report discussing the flying qualities of a high-speed bomber with a dual pusher propeller aft of the empennage. The airplane was found to have satisfactory flying qualities except for stability issues with aft center of gravity, high elevator control forces in landing, insufficient elevator control in take-off, and low rudder-free directional stability.
Report presenting information regarding the development of a type GB-5 controllable glide bomb equipped with a target-seeking device. The model was tested on the six-component balance in order to measure the stability and control characteristics of the bomb in its original condition and with various modifications. Results regarding the effect of end plates on dihedral parameter, effect of vertical-tail arrangement on directional stability, aileron tests, and glide-path control are provided.
Report presenting an investigation of the suitability of 27 aromatic amines for overwater storage of their gasoline blends. The program is also meant to determine the antiknock effectiveness and low-temperature solubility in gasoline.
Report presenting tests of airplane models that included investigations to determine the longitudinal stability and control, effects of various constituent parts or their modification on longitudinal stability and control, critical speed, and distribution of wing load. Some of the changes made in attempts to improve longitudinal control and to increase critical speed included auxiliary control flaps on the lower surface of the wing, revision of the windshield, increase in dimensions of outboard nacelles, and alteration in profile of wing leading edge.
Report presenting tests made in order to determine the differences in high-speed aerodynamic characteristics between models of a four-engine transport airplane and a similar bomber airplane. The main conclusion found is that the critical Mach number of the transport model is about 0.05 less than that of the bomber model.
"This report contains the results of tests of a full-scale semispan horizontal tail plane of a bomber airplane. The effects of fabric distortion on the aerodynamic characteristics of the elevator are determined by comparing the aerodynamic characteristics of a fabric-covered elevator with those of a metal-covered elevator. In addition, the results of cutting holes in the balance seal, the effect of fixing transition, the tab effectiveness both sealed and unsealed, and the section drag of this tail plane are presented" (p. 1).
Report discussing the mutual interference effects of tail surfaces and a stern propeller on a model of the XB-42.The main focus was to determine the effect of tail surface-propeller spacing upon the periodic tail surface loading coincident with propeller blade passage.
"F-3 and F-4 knock data are presented for blends of 0, 20, 40, 60, and 80 percent by volume of triptane in 28-R reference fuel plus approximately 4.6 ml TEL per gallon in the final blends. For comparison of knock-limited performance, 28-R reference fuel containing 2.7 percent by volume of xylidines and leaded to 6 ml TEL per gallon is included. In order to provide information on temperature sensitivities, two sets of modified conditions were used in addition to the standard F-4 engine conditions" (p. 1).
Report presenting tests to investigate the effect of 2-percent additions of 11 aromatic amines on the knock-limited performance of AN-F-28 fuel. A total of 48 aromatic amines are being prepared for knock tests. Results regarding the knock-limited performance data, antiknock effectiveness, and knock-limited powers are provided.
Report presenting testing to investigate the effects of 2-percent additions of nine aromatic amines on the knock-limited performance of AN-F-28 (28-R) fuel. The p-toluidine and p-tert-butylaniline gave the best overall improvement in the knock-limited power of the fuel.;
Report presenting tests to investigate the effect of 2-percent additions of nine aromatic amines on the knock-limited performance of AN-N-28 (28-R) fuel. The results of the testing of antiknock effectivneess of the 27 aromatic amines obtained to date in the program are also summarized.
Report discussing tests on the effect of 2-percent additions of 13 aromatic amines on the knock-limited performance of 28-R fuel in a CFR engine. The amines tested gave good rich mixture response at standard F-4 operating conditions, but were sensitive to engine severity at lean fuel-air ratios.
Report presenting a combination oil sump and scavenge pump constructed to eliminate some of the oil-system difficulties in an aircraft engine that result from the aeration of the scavenged engine oil and air-lock of the scavenge pump. Information regarding test results and design recommendations are provided.
Report presenting wind-tunnel tests of a 0.175-scale model of a midwing airplane in order to determine the high-speed longitudinal characteristics, to test devices for improving longitudinal control at high Mach numbers, and to determine the aileron effectiveness at high Mach numbers. Force and moment coefficients are computed from test data. Control forces, elevator angle, and aileron angle for several flight conditions are predicted.
Tests were undertaken to determine the relationships for estimating the maximum amount of a water-soluble gasoline additive that will diffuse from the gasoline to the water when fuel is stored over the water and to determine from the relationships the amount of xylidines that will diffuse from the gasoline to the water in an overwater-storage system.
Report presenting testing to determine the solubilities in gasoline at low temperatures of 15 aromatic amines from the NACA exploratory program as antiknock additives. The solubility data is summarized in a table by interpolating or extrapolating experimental results to obtain solubility at -60 degrees Celsius.
Report discussing testing of the Douglas A-26B to determine the longitudinal stability and control characteristics. Information about the elevator, stick-fixed and stick-free stability, center of gravity, and flap effects are described.
Flight tests were conducted on the OS2U-2 seaplane with simple circular-arc-type ailerons directly connected to the actuating torque tube. Two aileron test installations were made, differing only in the inclination of the projecting surface with the wing's upper surface. The lateral-control characteristics of the airplane were determined from data obtained in stalls and rudder-fixed aileron rolls. The revised ailerons were deficient in maximum rolling effectiveness, but were capable of controlling the rolling tendencies of the airplane near the stall.
This dialog allows you to filter your current search.
Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the World Regions listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Countries listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the U.S. States listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Months listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Days listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.