National Advisory Committee for Aeronautics (NACA) - 15 Matching Results

Search Results

Results: 1 - 15
open access

The Creep of Laminated Synthetic Resin Plastics

Description: "The long-time loading strength of a number of laminated synthetic resin plastics was ascertained and the effect of molding pressure and resin content determined. The best value was observed with a 30 to 40 percent resin content. The long-time loading strength also increases with increasing molding pressure up to 250 kg/cm(exp 2); a further rise in pressure affords no further substantial improvement" (p. 1)..
Date: November 1941
Creator: Perkuhn, H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Effect of Humidity on Several Supercharger Parameters

Description: Report presenting testing to determine if the change of several specific variables with extreme change of humidity and test-bench temperature will have an appreciable effect on several parameters used to determine supercharger performance.
Date: November 1941
Creator: Ellerbrock, Herman H., Jr. & Goldstein, Arthur W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Effect of Threaded and Serrated Holes on the Limited Time and Fatigue Strength of Flat Light-Alloy Strips

Description: "The investigation was made for the purpose of ascertaining the notch sensitivity of flat strips of light alloy with cylindrical holes under initial tension stress, with special attention to the change in notch-effect factors with the number of load cycles. Then the studies were extended to similar flat strips with pin-loaded holes (tension lugs). This report deals with fatigue tests under initial tension load on flat test specimens of 3116.5 duralumin and AZM 3510.1 electron with plain unloade… more
Date: November 1941
Creator: Bürnheim, H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Flight Measurements of the Elevator Deflections Used in Landings of Several Airplanes

Description: "A collection of data on the elevator deflections used in landings of several airplanes is presented in tabular form. The physical characteristics of these airplanes are also given. The elevator deflections used in landing some airplanes was found to be as much as 14.4 degrees greater than that used to stall under the same flight and loading conditions" (p. 1).
Date: November 1941
Creator: Vensel, Joseph R.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Investigation of performance of 9-cylinder engine using large valve overlap and eclipse fuel-injection system

Description: Report presenting single-cylinder tests were made with several different engines over a period of time, which have shown that a large overlap between the time of inlet valve opening and exhaust valve closing results in a considerable increase in the maximum power obtainable from a supercharged engine and reduces cylinder temperatures.
Date: November 1941
Creator: Young, Alfred W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

A Method of Determining the Equilibrium Performance and the Stability of an Engine Equipped With an Exhaust Turbosupercharger

Description: "The performance of an exhaust turbine driving a supercharger is investigated by means of a sample calculation based on reasonable assumptions for the purpose of determining whether the assumed installation is stable with respect to changes in the mass of gas handled, boost pressure, etc. The arrangement was found to be stable throughout the entire range of operation. The method developed can be generally applied" (p. 1).
Date: November 1941
Creator: Rea, James Buchanan
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Relief of Residual Stress in Streamline Tie Rods by Heat Treatment

Description: "About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees… more
Date: November 1941
Creator: Pollard, R. E. & Reinhart, Fred M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Researches on Direct Injection in Internal-Combustion Engines

Description: Report presenting a solution for reducing the fatigue of the Diesel engine by permitting the preservation of its components and, at the same time, raising its specific horsepower to a par with that of carburetor engines, while maintaining for the Diesel engine its perogative of burning heavy fuel under optimum economical conditions. The feeding of Diesel engines by injection pumps actuated by engine compression achieves the required high speeds of injection readily and permits rigorous control … more
Date: November 1941
Creator: Tuscher, Jean E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tests of a 0.1475c Aileron With a Tab on Low-Drag Section for Curtiss XP-60 Airplane in the Low-Turbulence Tunnel

Description: "Preliminary two-dimensional tests of the hinge-moment characteristics of a 0.1725c internally balanced aileron on the subject XP-60 wing section indicated that more internal balance would be required if light stick forces were to be obtained at high speeds. The present series of tests were therefore undertaken in order to investigate methods of reducing the slope of the hinge-moment curve while still maintaining the required aileron effectiveness" (p. 1).
Date: November 1941
Creator: von Doenhoff, A. E. & Underwood, W. J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Two-Dimensional Potential Flow Past a Smooth Wall With Partly Constant Curvature

Description: The speed of a two-dimensional flow potential flow past a smooth wall, which evinces a finite curvature jump at a certain point and approximates to two arcs in the surrounding area, has a vertical tangent of inflection in the critical point as a function of the arc length of the boundary curve. This report looks at a general theorem of the local character of the conformal function at the critical point as well as the case of the finite curvature jump.
Date: November 1941
Creator: v. Koppenfels, Werner
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Wind-Tunnel Development of a Plug-Type Spoiler-Slot Aileron for a Wing With a Full-Span Slotted Flap and a Discussion of Its Application

Description: Report presenting an investigation in the NACA 7- by 10-foot wind tunnel of several arrangements of a plug-type, spoiler-slot aileron on an NACA 23012 airfoil with a full-span slotted flap. The results indicated that a plug-type, spoiler-slot aileron probably has negligible drag in the neutral position and will provide satisfactory lateral control for airplanes equipped with full-span slotted flaps.
Date: November 1941
Creator: Rogallo, Francis M. & Swanson, Robert S.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Wind-Tunnel Investigation of Perforated Split Flaps for Use as Dive Brakes on a Tapered NACA 23012 Airfoil

Description: Aerodynamic characteristics of a tapered NACA 23012 airfoil with single and double perforated split flaps have been determined in the NACA 7- by 10-foot wind tunnel. Dynamic pressure surveys were made behind the airfoil at the approximate location of the tail in order to determine the extent and location of the wake for several of the flap arrangements. In addition, computations have been made of an application of perforated double split flaps for use as fighter brakes. The results indicated th… more
Date: November 1941
Creator: Purser, Paul E. & Turner, Thomas R.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Wind-Tunnel Investigation of Several Factors Affecting the Performance of a High-Speed Pursuit Airplane With Air-Cooled Radial Engine

Description: Report details an investigation into various potential improvements and modifications to pursuit airplanes. NACA low-drag airfoil sections and their use for reducing drag and increasing compressibility speeds were examined. Other items covered include the propeller slipstream, high-speed cowling arrangement, and placement of wing guns.
Date: November 1941
Creator: Wenzinger, Carl J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Wind-Tunnel Tests of Eight-Blade Single and Dual-Rotating Propellers in the Tractor Position

Description: Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade pro… more
Date: November 1941
Creator: Biermann, David & Gray, W. H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
Back to Top of Screen