Search Results

open access

Alkali Metal Physical Properties Program at Pratt & Whitney Aircraft-CANEL

Description: The favorable combination of physical properties such as heat capacity, viscosity, electrical resistivity, thermal conductivity and high temperature liquid range make alkali metals, in principle, among the best heat transfer fluids available for use in nuclear reactor and other esoteric powerplant systems. Unfortunately, many of these properties are not known with sufficient certainty in the high temperature region to permit optimization of design criteria for developing maximum efficiency coo… more
Date: June 15, 1962
Creator: Kapelner, S. M. & Cleary, Robert E., 1920-
Partner: UNT Libraries Government Documents Department
open access

An Analysis of Inconsistencies in Removal Cross Sections of Carbon and Oxygen

Description: Abstract. Some recent analysis of certain Lid Tank fast neutron dose rates measured in oil and water indicates that there are some basic inconsistencies with reported oxygen and carbon removal cross sections and the reported data. These inconsistencies may be explained in several ways: (1) The reported carbon removal cross section is wrong. (2) The reported oil composition is wrong. (3) The reported oxygen removal cross section is wrong since it is based on an assumed rather than a measured o… more
Date: January 20, 1961
Creator: {{{name}}}
Partner: UNT Libraries Government Documents Department
open access

Boiling Heat Transfer of Liquid Metals: a Literature Search

Description: This partially annotated bibliography contains references on boiling heat transfer of liquid metals. Emphasis is place on boiling heat transfer of liquid sodium, liquid potassium, and liquid rubidium. The period covered is 1950 to date. References are arranged alphabetically by title. Sources used in compiling this bibliography are: Abstracts of Classified Reports, Nuclear Science Abstracts.
Date: October 3, 1960
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Bonding of Tantalum

Description: Technical report describing the investigation undertaken to determine the necessary requirements for obtaining sound bonded joints on tantalum. Corrosion and Mass Transfer Loops LTTN 237A and 427 called for fabrication of 430 stainless steel clad tantalum tubing. Since there was little or no experience at welding this material at CANEL, specimens were welded using vacuum chambers and plastic chambers as normally used for loop fabrication. Resistance welding was performed without the use of a … more
Date: June 17, 1959
Creator: Rogers, S. L.
Partner: UNT Libraries Government Documents Department
open access

Braze Alloys v.s. Atmospheres : Final Report Project 1325

Description: Summary. At the time this project was initiated, all brazing had been confined to small retorts of ten cubic feet capacity or less. Larger assemblies were scheduled which required retorts of over 100 cubic feet capacity. Hydrogen atmospheres had given the best results, however, there was considerable reluctance to use hydrogen in these large retorts from a safety standpoint. It was thought that thru the use of PMC 2252, an argon - 2 1/2% hydrogen gas atmosphere which in non-explosive, suffici… more
Date: May 21, 1959
Creator: Rogers, S. L.
Partner: UNT Libraries Government Documents Department
open access

Braze Ring Mold for Sintering & Casting

Description: Technical report of an investigation to determine a suitable material for sintering and casting of braze rings. Braze rings afford an excellent means of preplacing braze alloy on tube to head joints of radiators, heat exchangers, and similar applications. A cast ring is especially desirable because of its increased strength. Previous efforts at casting had used welding grade carbon blocks with the desired ring cavities machined into their surface. Conclusion: Stackpole grade 331 electro-graphi… more
Date: May 14, 1959
Creator: Rogers, S. L.
Partner: UNT Libraries Government Documents Department
open access

Design Criteria for Lithium-Cooled Reactor Experiment (LCRE) at NRTS

Description: This technical report provides design criteria for reactor test facilities utilizing existing structures at the former ANP area of the National Reactor Testing Station (NRTS) near Idaho Falls, Idaho. The information and specifications presented establish the basis for the design of facilities providing the capability for installation, extended nuclear testing and remote disassembly of the 10mw Lithium-Cooled Reactor Experiment (LCRE). Facility structural and process design has been developed t… more
Date: September 4, 1962
Creator: Hedden, D. T.
Partner: UNT Libraries Government Documents Department
open access

Design Criteria for Reactor Test Support Facility at NRTS

Description: This technical report provides a design criteria for a technical support facility for the Lithium Cooled Reactor Experiment (LCRE) and SNAP-50-DR-1 Test Facilities. The support facility is adjacent to the LCRE Test Facility and is located completely within the existing Building 629 structure at the former ANP area of the National Reactor Testing Station (NRTS) near Idaho Falls, Idaho. The information and specifications presented establish the basis for the design of laboratories, shops and en… more
Date: September 14, 1962
Creator: Macfarlane, D. B.
Partner: UNT Libraries Government Documents Department
open access

Diffusion of Xenon in Columbium

Description: The diffusion coefficient was calculated for the diffusion of Xe through Nb and found to be 0.064 exp (-18,600/RT).
Date: November 20, 1959
Creator: Gregory, D. P. (Derek P.) & Leavenworth, H. W. (Howard W.)
Partner: UNT Libraries Government Documents Department
open access

Engineering Report on the Design of the Pratt & Whitney Aircraft Forced Convection Alkali Metal Vaporization Condensation Heat Transfer Rig

Description: Summary. A test rig has been designed to obtain basic two phase forced convection liquid metal heat transfer and pressure drop data for use in the design of liquid metal boilers. This engineering report includes background of the boiling problem, partial summary of work done by other investigators, the object, scope, engineering, and operations of this test rig, and a summary of reproducibility tests conducted in a water back-up rig.
Date: January 18, 1963
Creator: Bernstein, E.
Partner: UNT Libraries Government Documents Department
open access

Evaluation of Commercial Ceramic Coating for Short Time Protection of Columbium 1% Zirconium

Description: Abstract. Fourteen commercial enamel frits from five different manufacturers were tested to determine their abilities to protect Nb-1% Zr during the forging cycle in the temperature range of 1800 to 2300 deg F. One frit was found to afford good coverage and protection at 2200 deg F at times up to 5 hours of exposure. Adherence was excellent during upset forging of a coated Nb--1% Zr sample heated 45 minutes at 2200 deg F. Another frit afforded good protection and coverage at 1700 deg F. (auth)
Date: October 10, 1960
Creator: McGrath, D. W.
Partner: UNT Libraries Government Documents Department
open access

Fabrication of Beryllium: a Bibliography

Description: This bibliography contains 147 references on the fabrication of beryllium. References are also given on the brazing, casting, cladding, extrusion and welding of beryllium and some beryllium-rich alloys. The bibliography is limited to the period 1950 - 1959. references are arranged alphabetically by title, with author and subject indexes provided. Sources used in compiling this bibliography are: Abstracts of Classified Reports, ASM Review of Metal Literature, Bibliographies of Interest to the At… more
Date: April 1, 1960
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Filling Instructions for the Pratt & Whitney Forced Convection Liquid Metal Inpile Loop Experiment (PW19)

Description: The apparatus and procedures that are to be used to fill the liquid metal system of the Pratt and Whitney Forced Convection Liquid Metal Inpile Loop are described. The liquid metal to be used is a mixture containing 56% Na and 44% K, which is a liquid at room temperature. In order to simplify the filling procedure at the reactor site, two containers, each of which contains exactly enough liquid metal to fill the experiment to the prescribed level, a fill dolly incorporating a purified helium sy… more
Date: April 29, 1959
Creator: Heyl, P. T.
Partner: UNT Libraries Government Documents Department
open access

High Voltage Electron Beam Welding of W-RE Thermocouples

Description: A series of W-5 Re/W-26 Re thermocouples have been electron beam welded at the Hamilton Standard Division at our request. This technical report is a summary of our evaluation of these joints. These weldments did exhibit incomplete fusion in cap welds and some porosity in undesirable lead junction shapes. In fairness, this was a single attempt to make a difficult joint, and the objective of ungrounded 1/16 OD clad joints was met. As noted by Hamilton, two changes are necessary to improve this… more
Date: December 13, 1962
Creator: Doyle, J.
Partner: UNT Libraries Government Documents Department
open access

Hydrides of Titanium, Yttrium, and Zirconium: a Bibliography

Description: This bibliography contains 94 references on metal hydrides, with particular emphasis placed on the hydrides of titanium, yttrium, and zirconium. The bibliography covers the period 1955 through 1959. The references are arranged alphabetically by title. Sources used in compiling this bibliography are: Applied Science and Technology Index, Abstracts of Classified Reports, ASM Review of Metal Literature, Bibliographies of Interest to the Atomic Energy Program, Classified and Unclassified Parts, Ind… more
Date: April 28, 1960
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Producibility of an Alloy of Columbium with One Percent Zirconium

Description: Abstract. Proven mineral resources show that niobium is the most abundant of the refractory metals and extraction capacity is adequate to meet foreseeable requirements. Approximately four tons of Nb-1% Zr alloy were melted, forged, drawn, and rolled to produce various mill forms and relatively large die impression forgings. It was demonstrated that the Nb-1% Zr alloy is readily amenable to melting, primary working, and secondary working using standard equipment available in the specialty steel … more
Date: December 9, 1959
Creator: Raring, L M
Partner: UNT Libraries Government Documents Department
open access

Purification of Argon, Helium and Xenon : a Bibliography

Description: This bibliography contains 145 references on the technology and apparatus used in the purification of argon, helium and xenon, and on the analysis for water, carbon monoxide, hydrogen, nitrogen, and oxygen, in the purification process. The references are arranged in four classifications: general, argon, helium, and xenon. Within each classification, the references are arranged in chronological order.
Date: September 16, 1956
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Radiation Effects on Aluminum, Elastomers, and Lubricants: a Bibliography

Description: This bibliography contains 145 references on radiation effects on aluminum, elastomers, and lubricants. Also included are references on radiation units and conversion factors. The bibliography is limited to the period 1950 through 1959, with the references arranged alphabetically by title in five categories. An author index is provided. Sources used in compiling this bibliography are: Abstracts of Classified Reports, Bibliographies of Interest to the Atomic Energy Program: Classified and Unclas… more
Date: April 4, 1960
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Refractory Metals as Alkali Liquid Metal Containment Materials

Description: Abstract. Refractory metals and their alloys are good container materials for alkali metal coolants. Thermodynamics of interaction with contaminants have been correlated with experimental test and show the need for high purity materials. Structural metal solubility data to 1600F can be used to correlate and predict engineering systems.
Date: June 15, 1962
Creator: Cleary, Robert E., 1920-
Partner: UNT Libraries Government Documents Department
open access

Self-Shielding Cross Sections : a Bibliography

Description: This bibliography contains 37 references on self-shielding cross sections. The bibliography is limited to the period from 1951 through November 1959 with the references arranged alphabetically by title. The sources used in compiling this bibliography were: Abstracts of Classified Reports Nuclear Science Abstracts
Date: December 29, 1959
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Short Time Strength Data for CS 1830 Series Cb-1Zr, Annealed at 2200F

Description: This technical report is a summary of short time strength data for CS1830 series Cb-1Zr material. The data are presented as a function of fabrication history or the amount of cold work received during fabrication. Three fabrication categories were considered for comparison: forgings and extrusions; bar, plate, rod and pipe; and sheet and tubing. Forgings and extrusions having received no cold work showed the highest strength over the entire temperature range 68F to 2800F; bar, plate, rod and pi… more
Date: February 8, 1963
Creator: Watson, W. L.
Partner: UNT Libraries Government Documents Department
open access

Space Propulsion and Auxiliary Power Units: a Bibliography

Description: This partially annotated bibliography contains references on advanced space propulsion units. References are also included on auxiliary power units, energy requirements, and mission requirements. The references are arranged alphabetically by title, with corporate author and subject indexes provided. This bibliography is issued in two parts: CNLM-2370-3, Part I, contains unclassified references; CNLM2370-3, Part II, contains classified material. Sources used in compiling this bibliography are: A… more
Date: August 2, 1960
Creator: Cernak, Elizabeth A.
Partner: UNT Libraries Government Documents Department
open access

Spinning of Columbium & Columbium 1%- Zirconium Tubing

Description: The following objectives were planned for this project. (1) Development of spinning data necessary for spinning Columbium and Columbium-1% Zirconium tubing from ingot, forged or welded tube blanks. (2) Determine mechanical & metallurgical properties of spun Columbium and Columbium-1% Zirconium tubing. (3) Determine dimensional and tolerance limits possible to attain on spun Columbium and Columbium-1% Zirconium tubing based on our present equipment, tooling limitations, and the spinning tests p… more
Date: January 19, 1961
Creator: Barker, Wharton R.
Partner: UNT Libraries Government Documents Department
open access

Survey: Oxidation Characteristics of Columbium and Columbium Base Alloys

Description: Unclassified experimental data concerned with the oxidation characteristics of Nb and Nb-base alloys are presented. The bulk of the results is presented in tabular form and cataloged under laboratory name sub-headings. The theory of alloy development for oxidation resistance is discussed. Methods of evaluating oxidation behavior are outlined.
Date: May 20, 1959
Creator: Clough, W. R. (William Raymond); Hirakis, E. C. & Krutenat, R. C.
Partner: UNT Libraries Government Documents Department
Back to Top of Screen