Search Results

open access

Addendum to the Spert IV Hazards Summary Report: Capsule Driver Core

Description: From abstract: "explain all important features pertaining to a new pulsed irradiation reactor, the Capsule Driver, Core, and to analyze the potential problems and hazards of operating this reactor in the existing Spert IV facility."
Date: February 1965
Creator: Miller, R. W.; McCardell, Richard K. & Lagier, T. F.
Partner: UNT Libraries Government Documents Department
open access

Advanced Test Reactor Servo Regulator Rod Test Program

Description: From abstract: "Verify rod mechanism characteristics reported by the United Shoe Machinery Corporation, demonstrate that rod mechanism characteristics were compatible with reactor kinetics and that over-all reactor system behavior was stable, and to recommend system modifications needed for satisfactory performance."
Date: February 1964
Creator: Pickett, R. T., III
Partner: UNT Libraries Government Documents Department
open access

BWR Reference Design for PL-3

Description: Abstract: The natural circulation, direct cycle, boiling water reactor reference design presented in this technical report is the alternate to the preferred preliminary design developed under Phase I of the PL-3 contract. The report presents plant design criteria, summary of plant selection, plant description, reactor and primary system description, thermal and hydraulic analysis, nuclear analysis, control and instrumentation description, shielding description, auxiliary systems, power plant equipment, waste disposal, buildings and tunnels, services, operation and maintenance, logistics, erection, cost information and training program outline.
Date: February 28, 1962
Creator: Humphries, G. E.
Partner: UNT Libraries Government Documents Department
open access

Conceptual Design for 75 MWe Mixed Spectrum Superheating Reactor Power Plant

Description: "This report presents the conceptual design of a 75 MWe prototype Mixed Spectrum Superheater power plant. The scope of the work has emphasized primarily the design, performance, and cost information on the nuclear portion of the plant. The research and development programs required to insure plant feasibility are also present."--Intro.
Date: February 25, 1962
Creator: U.S. Atomic Energy Commission
Partner: UNT Libraries Government Documents Department
open access

Decontamination Program Task II. Volume 1, Contamination and Decontamination in Nuclear Power Reactors

Description: Abstract: A survey of the problem of reactor system contamination by radioactive material and methods that have been employed to remove the material was carried out. Following this survey, an investigation of chemical solutions was undertaken to find one which might be successfully employed in the decontamination of a stainless steel steam generator. From a preliminary screening, the most promising chemical method from the view point of minimum corrosion and maximum decontamination is a caustic permanganate treatment followed by and acid rinse.
Date: February 13, 1959
Creator: Zegger, John L. & Pancer, Guyon P.
Partner: UNT Libraries Government Documents Department
open access

Decontamination Program Task II. Volume II, Evaluation of Chemical Agents for Nuclear Reactor Decontamination

Description: Abstract: The caustic permanganate-rinse decontamination treatment was investigated. Loop and metallurgical studies were performed to determine optimum operating conditions as well as the metallurgical effects of the treatment. A treatment with 10 percent sodium hydroxide and 5 percent potassium permanganate solution followed by a rinse with a 5 percent ammonium citrate, 2 percent citric acid and 1/2 percent Versene solution was chosen for the decontamination of a stainless steel steam generator. Decontamination factors of greater than 50 were obtained in loop tests using the above treatment. Corrosion and metallurgical results indicated a total penetration of less than 0.01 mil on annealed Type 304 stainless steel with no evidence of any deleterious effects.
Date: February 15, 1959
Creator: Zegger, John L. & Pancer, Guyon P.
Partner: UNT Libraries Government Documents Department
open access

Decontamination Program Task II. Volume III, Recommended Procedure for Decontamination of a Stainless Steel Steam Generator

Description: Abstract: A decontamination procedure for a stainless steel steam generator similar to the APPR-1 using a fill-flush application of a caustic permanganate-citrate combination solution is recommended. The isolation of the steam generator is to be accomplished by means of specially designed plugs at the reactor vessel outlet and at the primary coolant pumps. Anticipated results, including corrosion rates and decontamination factors, are presented.
Date: February 13, 1959
Creator: Pancer, Guyon P. & Zegger, John L.
Partner: UNT Libraries Government Documents Department
open access

Evaluation of Iron- and Nickel-Base Alloys for Medium and High Temperature Reactor Applications, Part 1

Description: Report discussing the evaluation of the "behavior of austenitic and ferritic stainless steels, iron-chromium-aluminum base alloys and nickel-base superalloys, in medium and high temperature simulated reactor environments" (p. 2).
Date: February 1961
Creator: Pessl, H. J.
Partner: UNT Libraries Government Documents Department
open access

Evaluation of Kanigen, Electroless Nickel Plating for Steam Side of a Sodium Component Steam Generator

Description: Introduction: This is a final report on the evaluation of Kanigen electroless nickel plating for surfaces in contact with water and steam i a sodium heated AISI Type 316 stainless steel steam generator. The purpose of the coasting was to afford protection from stress corrosion cracking originating on the water-steam side of the unit. It has been concluded that the kanigen coating does not afford adequate protection for the services condition intended. This work was performed as part of the research and development program for the United States Atomic Energy Commission sodium Components Design Project.
Date: February 15, 1961
Creator: Alco Products (Firm).
Partner: UNT Libraries Government Documents Department
open access

Fission Product Activity in SM-1 Core I Primary System and Surface Contamination on SM-1 Type Fuel Elements. Task XVIII, Phases 2 and 3

Description: Abstract; The fission product data obtained during SM-1 Core I operation (June 1957 - May 1960) is reviewed briefly and interpreted. Evidence is presented to indicate that a fuel element defect was responsible for the high fission product activity level observed in the primary coolant. Relative escape coefficients are calculated and the defect size estimated. Anticipated fission product levels during SM-1 Core II and SM-1A Core I operation are estimated from alpha surface contamination data on completed fuel elements. The importance of in-line sampling for monitoring fission product activity is stressed as well as the need for failed fuel element detection methods.
Date: February 28, 1961
Creator: Hasse, Robert A. & Zegger, John L.
Partner: UNT Libraries Government Documents Department
open access

Fuels and Materials Development Program Quarterly Progress Report, September 30, 1968

Description: From Foreword: "Report containing information about ongoing research and development taking place in the Oak Ridge National Laboratory's Fuels and Materials Development Program. This includes a series of test reports covering such subjects as reactor fuels, the development of nitride fuels, and the effects of radiation on structural materials."
Date: February 1969
Creator: Oak Ridge National Laboratory. Metals and Ceramics Division.
Partner: UNT Libraries Government Documents Department
open access

Hazards Report for SM-1 Core Temperature and Flow Instrumentation (Task XIV) Covering Special Test Procedures.

Description: Abstract: Test procedures for special tests involving in-core SM-1 temperature and flow instrumentation are described (Task XIV Package Tests). These tests involve in-core steady state flow and temperature measurements, loss of flow transients, load transients, reduced primary system pressure operations and reduced element flow. The thermal and hydraulic conditions prevailing in these tests, including steady state and transient burnout rations, are developed. The effects of reduced system pressure and flow on the burnout ratios are determined as are the expected stuck rod conditions when Task XIV test elements are installed. The effect on the maximum credible accident is included and a recommendation to conduct these Task XIV package tests is made.
Date: February 28, 1962
Creator: Bradley, P. L. & Coombe, J. R.
Partner: UNT Libraries Government Documents Department
open access

Hazards Report for Step Transient Loading Tests on the SM-1 : Task XII

Description: Abstract: This technical report evaluates hazards involved with SM- 1 plant response and system performance tests (Task XII), to determine the response of the SM-1 plant to step electrical and steam load changes. The report describes the changes in plant equipment and operating procedures for this task and evaluates these changes for possible additional hazards to those described in APAE No. 2, Revision 1, "Hazards Summary Report for the Army Package Power Reactor SM-1."
Date: February 1, 1962
Creator: Pomeroy, D. L.
Partner: UNT Libraries Government Documents Department
open access

Intermediate Heat Exchanger Preliminary Design. Vol. 1, IHX Preliminary Design

Description: Preface: The intermediate heat exchanger is designed for operation in a nuclear power plant using liquid sodium as the primary and secondary coolant. Since the primary fluid coming from the reactor is radioactive, the purpose of the IHX is to transfer heat to a nonradioactive fluid which then goes to a steam generator. Because of this activity the until will be enclosed in a concrete pit and will not be accessible during periods of operation. Immediately after shut down it will be necessary to allow time for radioactive decay before the unit will be accessible to personnel. Because of inaccessibility and possible long periods allowed for decay time, it is imperative that the unit give trouble free operation. During periods of shut down, the internals should have easy access for inspection and repair if necessary so that down time is held to a minimum. The general arrangement of the heat exchanger described in this report presents a conventional design utilizing known materials and existing methods of fabrication. In further consideration of all concepts, designs and analyses developed during this period of the program, it is felt that this preliminary design will provide an intermediate sodium heat exchanger of lower cost and more reliable operation.
Date: February 28, 1959
Creator: Alco Products (Firm)
Partner: UNT Libraries Government Documents Department
Back to Top of Screen