Search Results

open access

D-0 South End Cap Calorimeter Cold Test Results

Description: The South endcap calorimeter vessel was moved into Lab A on Sept. 18, 1990. A cooldown of the pressure vessel with liquid nitrogen was performed on Sept. 26 to check the vessel's integrity. With the pressure vessel cold, the insulating vacuum was monitored for leaks. Through out the testing, the insulating vacuum remained good and the vessel passed the test. The cold test was carried out per the procedures of D-Zero engineering note 3740.220-EN-250. The test was very similar to the cold test performed on the Central Calorimeter in October of 1987. The test of the ECS was performed in the same manner using the same equipment as the ECN cold test. Reference D-Zero engineering notes 3740.210-EN-122, 3740.000-EN-I07, and 3740.210-EN-II0 for information about the CC cold test. Reference EN-260 for the results of the ECN cold test. The insulating vacuum space was pumped on while equipment was being connected to the pressure vessel. Two hours after starting to pump with the blower the vacuum space pressure was at about 40 microns. The pumping continued overnight (another 16 hours). In the morning the pressure was 11.5 microns. A rate of rise test was performed. With the pump valved off, the pressure rose to 14 microns within 5 minutes and then rose to 16 microns in 6 hours (0.33 microns/hour). After all connections were made to the pressure vessel, a vacuum pump with an estimated effective pumping speed of about 70 scfm was valved on. After 18 hours, the pressure vessel was down to 270 microns. An additional day of pumping took the pressure down to only 250 microns. A leak was then found and fixed around the seal of the rupture disc. The pump was put on line again. The pressure vessel with pump on line was 27 microns after 16.5 …
Date: November 26, 1990
Creator: Rucinski, R.
Partner: UNT Libraries Government Documents Department
open access

1?10 kW Stationary Combined Heat and Power Systems Status and Technical Potential: Independent Review

Description: This independent review examines the status and technical potential of 1-10 kW stationary combined heat and power fuel cell systems and analyzes the achievability of the DOE cost, efficiency, and durability targets for 2012, 2015, and 2020.
Date: November 1, 2010
Creator: Maru, H. C.; Singhal, S. C.; Stone, C. & Wheeler, D.
Partner: UNT Libraries Government Documents Department
open access

1-Dimensional simulation of thermal annealing in a commercial nuclear power plant reactor pressure vessel wall section

Description: The objective of this work was to provide experimental heat transfer boundary condition and reactor pressure vessel (RPV) section thermal response data that can be used to benchmark computer codes that simulate thermal annealing of RPVS. This specific protect was designed to provide the Electric Power Research Institute (EPRI) with experimental data that could be used to support the development of a thermal annealing model. A secondary benefit is to provide additional experimental data (e.g., thermal response of concrete reactor cavity wall) that could be of use in an annealing demonstration project. The setup comprised a heater assembly, a 1.2 in {times} 1.2 m {times} 17.1 cm thick [4 ft {times} 4 ft {times} 6.75 in] section of an RPV (A533B ferritic steel with stainless steel cladding), a mockup of the {open_quotes}mirror{close_quotes} insulation between the RPV and the concrete reactor cavity wall, and a 25.4 cm [10 in] thick concrete wall, 2.1 in {times} 2.1 in [10 ft {times} 10 ft] square. Experiments were performed at temperature heat-up/cooldown rates of 7, 14, and 28{degrees}C/hr [12.5, 25, and 50{degrees}F/hr] as measured on the heated face. A peak temperature of 454{degrees}C [850{degrees}F] was maintained on the heated face until the concrete wall temperature reached equilibrium. Results are most representative of those RPV locations where the heat transfer would be 1-dimensional. Temperature was measured at multiple locations on the heated and unheated faces of the RPV section and the concrete wall. Incident heat flux was measured on the heated face, and absorbed heat flux estimates were generated from temperature measurements and an inverse heat conduction code. Through-wall temperature differences, concrete wall temperature response, heat flux absorbed into the RPV surface and incident on the surface are presented. All of these data are useful to modelers developing codes to simulate RPV annealing.
Date: November 1, 1994
Creator: Nakos, J. T.; Rosinski, S. T. & Acton, R. U.
Partner: UNT Libraries Government Documents Department
open access

A-01 metals in stormwater runoff evaluation

Description: As a part of the A-01 investigation required by the NPDES permit, an investigation was performed to ascertain the concentrations of metals specifically copper (Cu), lead (Pb), and zinc (Zn) in stormwater being discharged through the outfall. This information would indicate whether all water being discharged would have to be treated or if only a portion of the discharged stormwater would have to be treated. A study was designed to accomplish this. The first goal was to determine if the metal concentrations increased, decreased, or remained the same as flow increased during a rain event. The second goal was to determine if the concentrations in the storm water were due to dissolved. The third goal was to obtain background data to ascertain if effluent credits could be gained due to naturally occurring metals.Samples from this study were analyzed and indicate that the copper and lead values increase as the flow increases while the zinc values remain essentially the same regardless of the flow rate. Analyses of samples for total metals, dissolved metals, TSS, and metals in solids was complicated because in all cases metals contamination was found in the filters themselves. Some conclusions can be derived if this problem is taken into account when analyzing the data. Copper concentrations in the total and dissolved fractions as well as the TSS concentrations followed the hydrograph at this outfall but the copper in solids concentration appeared to peak in the first flush and decline to nondetectable rapidly over the course of the storm event. Lead was present in the total analysis but not present in the dissolved fraction or the solids fraction of the samples. The data for zinc was interesting in that the dissolved fractions were higher than the total fraction in three out of four samples. This is probably due …
Date: November 6, 1997
Creator: Eldridge, L. L.
Partner: UNT Libraries Government Documents Department
open access

2-D linear motion system. Innovative technology summary report

Description: The US Department of Energy's (DOE's) nuclear facility decontamination and decommissioning (D and D) program requires buildings to be decontaminated, decommissioned, and surveyed for radiological contamination in an expeditious and cost-effective manner. Simultaneously, the health and safety of personnel involved in the D and D activities is of primary concern. D and D workers must perform duties high off the ground, requiring the use of manlifts or scaffolding, often, in radiologically or chemically contaminated areas or in areas with limited access. Survey and decontamination instruments that are used are sometimes heavy or awkward to use, particularly when the worker is operating from a manlift or scaffolding. Finding alternative methods of performing such work on manlifts or scaffolding is important. The 2-D Linear Motion System (2-D LMS), also known as the Wall Walker{trademark}, is designed to remotely position tools and instruments on walls for use in such activities as radiation surveys, decontamination, and painting. Traditional (baseline) methods for operating equipment for these tasks require workers to perform duties on elevated platforms, sometimes several meters above the ground surface and near potential sources of contamination. The Wall Walker 2-D LMS significantly improves health and safety conditions by facilitating remote operation of equipment. The Wall Walker 2-D LMS performed well in a demonstration of its precision, accuracy, maneuverability, payload capacity, and ease of use. Thus, this innovative technology is demonstrated to be a viable alternative to standard methods of performing work on large, high walls, especially those that have potential contamination concerns. The Wall Walker was used to perform a final release radiological survey on over 167 m{sup 2} of walls. In this application, surveying using a traditional (baseline) method that employs an aerial lift for manual access was 64% of the total cost of the improved technology. However, for areas over approximately …
Date: November 1, 1998
Partner: UNT Libraries Government Documents Department
open access

3-D Reservoir and Stochastic Fracture Network Modeling for Enhanced Oil Recovery, Circle Ridge Phosphoria/Tensleep Reservoir, Wind River Reservation, Arapaho and Shoshone Tribes, Wyoming

Description: This report describes the results made in fulfillment of contract DE-FG26-00BC15190, ''3-D Reservoir and Stochastic Fracture Network Modeling for Enhanced Oil Recovery, Circle Ridge Phosphoria/Tensleep Reservoir, Wind River Reservation, Arapaho and Shoshone Tribes, Wyoming''. The goal of this project is to improve the recovery of oil from the Tensleep and Phosphoria Formations in Circle Ridge Oilfield, located on the Wind River Reservation in Wyoming, through an innovative integration of matrix characterization, structural reconstruction, and the characterization of the fracturing in the reservoir through the use of discrete fracture network models. Fields in which natural fractures dominate reservoir permeability, such as the Circle Ridge Field, often experience sub-optimal recovery when recovery processes are designed and implemented that do not take advantage of the fracture systems. For example, a conventional waterflood in a main structural block of the Field was implemented and later suspended due to unattractive results. It is estimated that somewhere less than 20% of the OOIP in the Circle Ridge Field have been recovered after more than 50 years' production. Marathon Oil Company identified the Circle Ridge Field as an attractive candidate for several advanced IOR processes that explicitly take advantage of the natural fracture system. These processes require knowledge of the distribution of matrix porosity, permeability and oil saturations; and understanding of where fracturing is likely to be well-developed or poorly developed; how the fracturing may compartmentalize the reservoir; and how smaller, relatively untested subthrust fault blocks may be connected to the main overthrust block. For this reason, the project focused on improving knowledge of the matrix properties, the fault block architecture and to develop a model that could be used to predict fracture intensity, orientation and fluid flow/connectivity properties. Knowledge of matrix properties was greatly extended by calibrating wireline logs from 113 wells with incomplete or older-vintage …
Date: November 18, 2002
Creator: La Pointe, Paul; Hermanson, Jan; Parney, Robert; Eiben, Thorsten; Dunleavy, Mike; Steele, Ken et al.
Partner: UNT Libraries Government Documents Department
open access

3-D UNSTRUCTURED HEXAHEDRAL-MESH Sn TRANSPORT METHODS

Description: This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). We have developed a method for solving the neutral-particle transport equation on 3-D unstructured hexahedral meshes using a S{sub n} discretization in angle in conjunction with a discontinuous finite-element discretization in space and a multigroup discretization in energy. Previous methods for solving this equation in 3-D have been limited to rectangular meshes. The unstructured-mesh method that we have developed is far more efficient for solving problems with complex 3-D geometric features than rectangular-mesh methods. In spite of having to make several compromises in our spatial discretization technique and our iterative solution technique, our method has been found to be both accurate and efficient for a broad class of problems.
Date: November 1, 2000
Creator: Morel, J. & McGhee, J.
Partner: UNT Libraries Government Documents Department
open access

3-Dimensional Flow Modeling of a Proposed Hanford Waste Treatment Plant Ion-Exchange Column Design

Description: Historically, it has been assumed that the inlet and outlet low activity waste plenums would be designed such that a nearly uniform velocity profile would be maintained at every axial cross-section (i.e., providing nearly 100 percent use of the resin bed). With this proposed design, we see a LAW outlet distributor that results in significant non-axial velocity gradients in the bottom regions of the bed with the potential to reduce the effectiveness'' of the overall resin bed. The magnitude of this efficiency reduction depends upon how far up-gradient of the LAW outlet these non-axial velocities persist and to what extent a ''dead-zone'' is established beneath the LAW outlet. This can impact loading and elution performance of the ion-exchange facility. Currently, no experimental studies are planned. The primary objective of this work was, through modeling, to assess the fluid dynamic impact on ''effective'' resin volume of the full-scale column based on its normal operation using a recently proposed LAW outlet distributor. The analysis effort was limited to 3-D flow only analyses (i.e., no follow on transport analyses) with 3-D particle tracking to approximate the impact that a nonaxial velocity profile would have on bed ''effectiveness''. Additional analyses were performed to estimate under nominal operating conditions the thermal temperature rise across a loaded resin bed and within its particles. Hydrogen bubble formation is not considered in the heat transfer analysis or in the determination of minimum flowrate. All modeling objectives were met.
Date: November 2002
Creator: Aleman, Sebastian
Partner: UNT Libraries Government Documents Department
open access

5 MeV Mott polarimeter for rapid precise electron beam polarization measurements

Description: Low energy (E{sub k} = 100 keV) Mott scattering polarimeters are ill-suited to support operations foreseen for the polarized electron injector at Jefferson Lab. One solution is to measure the polarization at 5 MeV where multiple and plural scattering are unimportant and precision beam monitoring is straightforward. The higher injector beam current offsets the lower cross-sections; measured rates scale to 1 kHz/{mu}A with a 1 {mu}m thick gold target foil.
Date: November 1, 1997
Creator: Price, J. S.; Poelker, B. M. & Sinclair, C. K.
Partner: UNT Libraries Government Documents Department
open access

6.70 EV Resonance in U²³⁸

Description: "Using the Brookhaven fast chopper, transmission curves were obtained for the 6.70 +/- .06 ev resonance in U238 using four different thicknesses of natural uranium metal." The measurements for the transmission curves are summarized in the table provided.
Date: November 9, 1953
Creator: Levin, Jules S.
Partner: UNT Libraries Government Documents Department
open access

The “8(a) Program” for Small Businesses Owned and Controlled by the Socially and Economically Disadvantaged: Legal Requirements and Issues

Description: This report discusses the "8(a) Program", the Minority Small Business and Capital Ownership Development Program, which is a federal contracting for small businesses providing small businesses with training, technical assistance, and contracting opportunities.
Date: November 26, 2014
Creator: Manuel, K. M.
Partner: UNT Libraries Government Documents Department
open access

9/11 Commission Recommendations: The Senate Confirmation Process for Presidential Nominees

Description: On July 22, 2004, the National Commission on Terrorist Attacks Upon the United States, known as the 9/11 Commission, issued its final report, detailing the events up to and including the September 11, 2001 terrorist attacks upon the United States. The 9/11 Commission recommended that the Senate adopt rules requiring hearings and votes to confirm or reject national security nominees within 30 days of their submission at the start of each new presidential administration. Implementing the commission's proposal would involve imposing new restrictions on both the power of committee chairs to control the agenda of their committees and the rights of Senators to delay or block nominations through holds and extended debate. This report discusses in detail this proposal, how it could be implemented, and the potential effects of its implementation.
Date: November 22, 2004
Creator: Palmer, Betsy
Partner: UNT Libraries Government Documents Department
open access

A 12-MW-scale pilot study of in-duct scrubbing (IDS) using a rotary atomizer

Description: A low-cost, moderate-removal efficiency, flue gas desulfurization (FGD) technology was selected by the US Department of Energy for pilot demonstration in its Acid Rain Precursor Control Technology Initiative. The process, identified as In-Duct Scrubbing (IDS), applies rotary atomizer techniques developed for lime-based spray dryer FGD while utilizing existing flue gas ductwork and particulate collectors. IDS technology is anticipated to result in a dry desulfurization process with a moderate removal efficiency (50% or greater) for high-sulfur coal-fired boilers. The critical elements for successful application are: (1) adequate mixing of sorbent droplets with flue gas for efficient reaction contact, (2) sufficient residence time to produce a non-wetting product, and (3) appropriate ductwork cross-sectional area to prevent deposition of wet reaction products before particle drying is comple. The ductwork in many older plants, previously modified to meet 1970 Clean Air Act requirements for particulate control, usually meet these criteria. A 12 MW-scale IDS pilot plant was constructed at the Muskingum River Plant of the American Electric Power System. The pilot plant, which operates from a slipstrem attached to the air-preheater outlet duct from the Unit 5 boiler at the Muskingum River Plant (which burns about 4% sulfur coal), is equipped with three atomizer stations to test the IDS concept in vertical and horizontal configurations. In addition, the pilot plant is equipped to test the effect of injecting IDS off- product upstream of the atomizer, on SO{sub 2}and NO{sub x} removals.
Date: November 1, 1989
Creator: Samuel, E. A.; Murphy, K. R. & Demian, A.
Partner: UNT Libraries Government Documents Department
open access

A 12-MW-scale pilot study of in-duct scrubbing (IDS) using a rotary atomizer

Description: A low-cost, moderate-removal efficiency, flue gas desulfurization (FGD) technology was selected by the US Department of Energy for pilot demonstration in its Acid Rain Precursor Control Technology Initiative. The process, identified as In-Duct Scrubbing (IDS), applies rotary atomizer techniques developed for lime-based spray dryer FGD while utilizing existing flue gas ductwork and particulate collectors. IDS technology is anticipated to result in a dry desulfurization process with a moderate removal efficiency (50% or greater) for high-sulfur coal-fired boilers. The critical elements for successful application are: (1) adequate mixing of sorbent droplets with flue gas for efficient reaction contact, (2) sufficient residence time to produce a non-wetting product, and (3) appropriate ductwork cross-sectional area to prevent deposition of wet reaction products before particle drying is comple. The ductwork in many older plants, previously modified to meet 1970 Clean Air Act requirements for particulate control, usually meet these criteria. A 12 MW-scale IDS pilot plant was constructed at the Muskingum River Plant of the American Electric Power System. The pilot plant, which operates from a slipstrem attached to the air-preheater outlet duct from the Unit 5 boiler at the Muskingum River Plant (which burns about 4% sulfur coal), is equipped with three atomizer stations to test the IDS concept in vertical and horizontal configurations. In addition, the pilot plant is equipped to test the effect of injecting IDS off- product upstream of the atomizer, on SO{sub 2}and NO{sub x} removals.
Date: November 1, 1989
Creator: Samuel, E. A.; Murphy, K. R. & Demian, A.
Partner: UNT Libraries Government Documents Department
open access

The 16 August 1997 Novaya Zemlya seismic event as viewed from GSN stations KEV and KBS

Description: Using current and historic seismic records from Global Seismic Network stations KEV and KBS, the authors find that S minus P arrival time comparisons between nuclear explosions and the 16 August 1997 seismic event (m{sub b} {approx} 3.6) from near Novaya Zemlya clearly indicate that (relative to KEV) the 16 August event occurred at least 80 km east of the Russian test site. Including S minus P arrival times from KBS constrains the location to beneath the Kara Sea and in good agreement with previously reported locations, over 100 km southeast of the test site. From an analysis of P{sub n}/S{sub n} waveform ratios at frequencies above 4 Hz, they find that the 16 August event falls within the population of regional earthquakes and is distinctly separated from Novaya Zemlya and other northern Eurasian nuclear explosion populations. Thus, given its location and waveform characteristics, they conclude the 16 August event was an earthquake. The 16 August event was not detected at teleseismic distances, and thus, this event provides a good example of the regional detection, location, and identification efforts that will be required to monitor the Comprehensive Test Ban Treaty below m{sub b} {approx} 4.
Date: November 1, 1997
Creator: Hartse, H.E.
Partner: UNT Libraries Government Documents Department
open access

N-17, A Delayed Neutron Emitter

Description: The decay scheme of a 4.2 second neutron emitter has been investigated in detail. Chemical and physical evidence shows that it is N{sup 17}, which emits beta rays to a broad excited state of O{sup 17}, which then breaks up into a neutron plus O{sup 16}. The energy spectrum of the neutrons is determined by measuring the energies of the O{sup 16} recoils in a proportional counter. The neutrons have a most probable energy of 0.9 Mev, a 'half width' of less than .5 Mev, and an upper limit of about 2 Mev. {beta}-recoil coincidences are observed, as predicted by the Bohr-Wheeler theory, and the {beta}-ray energy is measured by absorption. The beta rays in coincidence with neutrons have an upper limit of 3.7 {+-} 0.2 Mev. Beta-rays directly to the ground stat of O{sup 17} are not observed because of high background effects, but should have an energy of 8.7 Mev. Some evidence is presented to show that energy is conserved in the {beta}-n transition through the broad excited state in O{sup 17}.
Date: November 5, 1948
Creator: Alvarez, L. W.
Partner: UNT Libraries Government Documents Department
open access

17-keV x-ray output of plutonium

Description: In the production of plutonium in a reactor, plutonium-238, 240, and 241 are formed as well as Pu{sup 239}. It is well known that the specific alpha activity of the plutonium varies as the percentages of these isotopes are changed. Kinderman, et al have worked out the relationship between isotopic content and MWD/ton exposure. Their findings are reported in this document.
Date: November 5, 1958
Creator: McCall, R. C. & Bernard, R. M.
Partner: UNT Libraries Government Documents Department
open access

20-MW Magnicon for ILC

Description: The 1.3 GHz RF power to drive ILC is now planned to be supplied by 600-1200, 10-MW peak power multi-beam klystrons. In this project, a conceptual design for 1.3 GHz magnicons with 20 MW peak power was developed as an alternative to the klystrons, with the possibility of cutting in half the numbers of high-power tubes and associated components. Design of a conventional magnicon is described, using TM110 modes in all cavities, as well as design of a modified magnicon with a TE111 mode output cavity. The latter has the advantage of much lower surface fields than the TM110 mode, with no loss of output power or electronic efficiency.
Date: November 29, 2006
Creator: Hirshfield, Jay L.
Partner: UNT Libraries Government Documents Department
open access

S-20 photocathode research activity. Part I

Description: The goal of this activity has been to develop and implement S-20 photocathode processing techniques at Lawrence Livermore National Laboratory (LLNL) in order to study the physical properties of the photocathode films. The present work is the initial phase of a planned activity in understanding cathode fabrication techniques and the optical/electrical characterization of these films.
Date: November 22, 1983
Creator: Gex, F.; Huen, T. & Kalibjian, R.
Partner: UNT Libraries Government Documents Department
open access

40-kW field test power plant modification and development. Monthly technical status report No. 13, September 16, 1978-October 15, 1978

Description: The contract objective is to complete the design and development actions that upgrade the 40-kW fuel cell power plant to a configuration suitable for on-site demonstration testing. The modifications will improve operating capability, durability and maintenance interval and lead to reduced production costs. Equipment to recover and use the by-product heat of electric generation will be available on the power plant for field verification of on-site heat recovery. The 40-kW power plant will be compatible with the power characteristics required for conventional heat pumps and conventional 60 Hz, 120/208 volts electrically operated equipment. Progress is reported. (WHK)
Date: November 10, 1978
Partner: UNT Libraries Government Documents Department
open access

45-Day deliverable for Tank 241-BX-105 Auger samples, risers 2 and 6

Description: Two auger samples from single-shell tank 241-BX-105 (BX-105) were extruded, broken down, and analyzed for DSC, TGA, and total alpha as prescribed. Analytical results were tracked and reported using the laboratory information management system known as LabCore. This is the final report for the fiscal year 1995 BX-105 auger sample characterization effort. Included are copies of the differential scanning calorimetry (DSC) and thermogravimetric analyses (TGA) scans as requested. Also included is a copy of any immediate notification documentation, chain of custody forms, the hot cell work plan, extruded segment [auger] description sheets, and total alpha data.
Date: November 16, 1994
Creator: Bell, K. E.
Partner: UNT Libraries Government Documents Department
Back to Top of Screen