106 Matching Results

Search Results

Results: 1 - 24 next
open access

Aerodynamic Characteristics of a 4-Engine Monoplane Showing Comparison of Air-Cooled and Liquid-Cooled Engine Installations

Description: From Introduction: "An investigation has been conducted in the N.A.C.A. full-scale wind tunnel to determine the aerodynamic characteristics of a 1/4-scale model of a 4-engine monoplane when equipped with comparable air-cooled engine and liquid-cooled engine installations. The air-cooled engine installation consisted of nacelles equipped with N..A.C.A. cowlings and oil coolers located in the leading edge of the wing."
Date: July 1939
Creator: Silverstein, Abe & Wilson, Herbert A., Jr.
Partner: UNT Libraries Government Documents Department
open access

Aerodynamic Characteristics of Several Modifications of a 0.45-Scale Model of the Vertical Tail of the Curtiss XP-62 Airplane

Description: "In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane" (p. 1).
Date: July 1946
Creator: Lowry, John G.; Turner, Thomas R. & Liddell, Robert B.
Partner: UNT Libraries Government Documents Department
open access

Airfoil-Contour Modifications Based on (Epsilon)-Curve Method of Calculating Pressure Distribution

Description: From Introduction: "Certain alternations of a qualitative nature may be performed in spite of the fact that a pressure change cannot be prescribed. It is the purpose of this paper to indicate a method by which qualitative alternation may be performed. It will be noted that the present method of contour modification will serve the intended purpose of the inverse method."
Date: July 1944
Creator: Theodorsen, Theodore
Partner: UNT Libraries Government Documents Department
open access

Airspeed Fluctuations as a Measure of Atmospheric Turbulence

Description: "Increments in structural loads due to atmospheric turbulence can be accurately expressed in terms of flight speed and effective gust velocities (reference 4). Data from which the effective gust velocities could be computed were also obtained during the flights of the XC-35 airplane. These data have been used to determine the significance of the fluctuations in the pilot's indicated-airspeed readings in relation to structural loads to due to atmospheric turbulence" (p. 3).
Date: July 1945
Creator: Tolefson, H. B.
Partner: UNT Libraries Government Documents Department
open access

Aluminum-Zinc-Magnesium-Copper Casting Alloys

Description: From Introduction: "This paper contains data on the mechanical properties of sand-cast test bars having a considerable range in zinc, magnesium, and copper content and more detailed data on the properties and foundry characteristics of an aluminum-zinc-magnesium-copper alloy having a preferred composition for high strength and ductility."
Date: July 1941
Creator: Kempf, L. W.
Partner: UNT Libraries Government Documents Department
open access

An analysis of life expectancy of airplane wings in normal cruising flight

Description: From Summary: "The independent variables considered in the analysis included stress-concentration factor, stress-load relation, wing loading, design and cruising speeds, design gust velocity, and airplane size. Several methods for estimating fatigue life from gust frequencies are discussed."
Date: July 1945
Creator: Putnam, Abbott A.
Partner: UNT Libraries Government Documents Department
open access

Analysis of V-G Records from the SNB-1 Airplane

Description: Availability data obtained on SNB-1 trainer-class airplanes were analyzed and results presented as flight envelopes which predict occurrences of large values of air speed and acceleration. Comparison is made with SNJ-4 trainer-class airplane data analyzed by the same method. It is concluded that flight envelopes are satisfactory; that the two types show large differences in flight loads and speeds experience; and that SNB-1 will seldom, if ever, exceed design limit load factor and restricted sp… more
Date: July 1946
Creator: Walker, Walter G. & Meadows, May T.
Partner: UNT Libraries Government Documents Department
open access

Blade Design Data for Axial-Flow Fans and Compressors

Description: Report presenting an investigation to obtain blade design data for high-efficiency axial-flow fans and compressors, which were carried out in a two-dimensional low-speed cascade tunnel. The effects of camber, solidity, and stagger on blade turning angle and the shape of pressure distributions were determined for a family of five low-drag airfoils.
Date: July 1945
Creator: Bogdonoff, Seymour M. & Bogdonoff, Harriet E.
Partner: UNT Libraries Government Documents Department
open access

Calculated effects of full-span slotted and Fowler flaps on longitudinal stability and control characteristics for a typical fighter-type airplane with various tail modifications

Description: Report presenting an analytical study of the influence of full-span slotted and Fowler flaps on the requirements for horizontal tail surfaces. The elevator deflection required to land at three-point attitude, elevator deflection required to stall the airplane at altitude, and permissible center-of-gravity range have been calculated for a fighter-type airplane.
Date: July 1942
Creator: Goranson, R. Fabian
Partner: UNT Libraries Government Documents Department
open access

Calibrations of pitot-static tubes at high speeds

Description: Report presenting the calibrations of three types of service pitot-static tubes over an approximate range of speeds of 150 to 600 miles per hour. The calibrations indicated a need for a pitot-static tube with greater accuracy, especially at higher speeds. Results regarding the service tubes, Prandtl tube, Eigh-speed tube, and a comparison of the tubes are provided.
Date: July 1942
Creator: Hensley, Reece V.
Partner: UNT Libraries Government Documents Department
open access

Column and plate compressive strengths of aircraft structural materials: extruded 24S-T aluminum alloy

Description: Report presenting column and plate compressive strengths of extruded 24S-T aluminum alloy determined both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-, and channel-section columns. The tests are part of a research investigation to provide data on the structural strength of various aircraft materials. Results regarding compressive stress-strain curves and column and plate compressive strengths are provided.
Date: July 1945
Creator: Heimerl, George J. & Roy, J. Albert
Partner: UNT Libraries Government Documents Department
open access

Column and Plate Compressive Strengths of Aircraft Structural Materials: Extruded 24S-T Aluminum Alloy

Description: Column and plate compressive strengths of extruded 24S-T aluminum alloy were determined both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-,and channel-section columns. These tests are part of an extensive research investigation to provide data on the' structural strength of various aircraft materials. The results are presented in the form of curves and charts that are suitable for use in the design and analysis of aircraft structures.
Date: July 1945
Creator: Heimerl, George J. & Roy, J. Albert
Partner: UNT Libraries Government Documents Department
open access

Column and plate compressive strengths of aircraft structural materials: extruded 75S-T aluminum alloy

Description: Report presenting column and plate compressive strengths of extruded 75S-T aluminum alloy both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-, and channel-section columns. The tests are part of an extensive research investigation to provide data on the structural strength of various aircraft materials. Results regarding compressive stress-strain curves and column and plate compressive strengths are provided.
Date: July 1945
Creator: Heimerl, George J. & Roy, J. Albert
Partner: UNT Libraries Government Documents Department
open access

Comparison of Structural Efficiencies of Diagonal-Tension Webs and Truss Webs of 24S-T Aluminum Alloy

Description: "A comparison is made of the structural efficiencies of truss webs of 24S-T aluminum alloy with previously published values of the structural efficiencies of diagonal-tension webs of 24S-T aluminum alloy on the basis of identical allowable stresses. It is concluded that the diagonal-tension beam (web and flanges) can usually be built to be a more efficient beam than the truss beam, even though over a small range the web of a Warren truss beam is slightly more efficient than the web of a diagona… more
Date: July 1945
Creator: Ochiltree, David W.
Partner: UNT Libraries Government Documents Department
open access

A Comparison of Two Flight-Test Procedures for the Determination of Aileron Control Capabilities of an Airplane

Description: Report presenting a comparison of two flight-test procedures for the determination of the aileron control capabilities of an airplane. The procedures consist of performing rudder-fixed aileron rolls from straight unbanked flight and from steady turning flight. Results regarding rate of roll comparison and sideslip-angle comparison are provided.
Date: July 1945
Creator: Skoog, Richard B.
Partner: UNT Libraries Government Documents Department
open access

Compressibility and Heating Effects on Pressure Loss and Cooling of a Baffled Cylinder Barrel

Description: Report presenting testing to obtain experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. Testing occurred over a wide range of air flows and density altitudes.
Date: July 1944
Creator: Goldstein, Arthur W. & Ellerbrock, Herman H., Jr.
Partner: UNT Libraries Government Documents Department
open access

Control of Cylinder Temperatures by Thermostatically Operated Internal-Coolant Valves

Description: Report discusses the results of testing conducted to determine the performance of automatic, internal-coolant valves actuated by cylinder temperatures.The performance of the valves with respect to temperature sensitivity, rapidity of response, and hunting characteristics is described. The relative effects on cylinder performance obtained by internally supplying water and additional fuel were also examined.
Date: July 1945
Creator: Biermann, Arnold E.; Henneberry, Hugh M. & Miller, George R.
Partner: UNT Libraries Government Documents Department
open access

Cooling Tests of an Air-Cooled Engine Cylinder With Copper Fins on the Barrel

Description: Report presenting the results of comparative cooling tests run on two Wright C9GC (G-200) cylinders, one with the original steel fins and one with 1-inch spiral copper fins brazed on the barrel. Calculations were also performed using copper and aluminum fins with the same weight as the original steel fins, which showed positive results. Results regarding cylinder-temperature correlation, piston-temperature correlation, and comparative performance are also provided.
Date: July 1942
Creator: Sanders, J. C.; Wilsted, H. D. & Mulcahy, B. A.
Partner: UNT Libraries Government Documents Department
open access

Design charts for cross-flow tubular intercoolers charge-through-tube type

Description: Report presenting equations relating the various dimensions, air weight flow, and performance of a cross-flow tubular intercooler in which the charge flows through and the cooling air across the tubes. A method of determining and presenting the performance of a given intercooler at various operating conditions is indicated. Results regarding the cooling effectiveness equation, effect of primary intercooler variables, design charts, effect of tube arrangement on intercooler characteristics, and … more
Date: July 1941
Creator: Reuter, J. George & Valerino, Michael F.
Partner: UNT Libraries Government Documents Department
open access

Design, selection, and installation of aircraft heat exchangers

Description: Report presenting a survey of aircraft heat exchangers in three parts: design, selection, and installation. Appendices give the physical properties of air, properties of standard atmosphere as defined by the Navy, Army, and NACA, and an impact-pressure chart.
Date: July 1943
Creator: Wood, George P. & Brevoort, Maurice J.
Partner: UNT Libraries Government Documents Department
open access

Determination of General Relations for the Behavior of Turbulent Boundary Layers

Description: Report presenting an analysis of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. Results indicate that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter.
Date: July 1943
Creator: von Doenhoff, Albert E. & Tetervin, Neal
Partner: UNT Libraries Government Documents Department
open access

Determination of the Stability and Control Characteristics of Airplanes from Tests of Powered Models

Description: Report presenting a technique of testing wind tunnel powered models developed as a result of experience gained in the investigation of the static longitudinal and lateral staiblity and control characteristics of several powered models in the 7- by 10-foot wind tunnel. A discussion of the conditions to be investigated, methods of presenting and interpreting the data, and a suggested operating technique are given.
Date: July 1942
Creator: Recant, Isidore G.
Partner: UNT Libraries Government Documents Department
open access

The development and application of high-critical-speed nose inlets

Description: From Summary: "An analysis of the nose-inlet shapes developed in previous investigations to represent the optimum from the standpoint of critical speed has shown that marked similarity exists between the nondimensional profiles of inlets which have widely different proportions and critical speeds. With the nondimensional similarity of such profiles established, the large differences in the critical speeds of these nose inlets must be a function of their proportions. An investigation was underta… more
Date: July 1945
Creator: Baals, Donald D.; Smith, Norman F. & Wright, John B.
Partner: UNT Libraries Government Documents Department
open access

Drag Measurements of a Protruding 0.50-Caliber Machine Gun

Description: Report presenting drag and cross-wind force measurements of a Browning 0.50-caliber M2 machine gun at a range of air speeds in the NACA wind tunnel. The gun protruded through the top of the tunnel wall into the air stream and tests were performed at a variety of angles in order to determine the power required to turn the gun against the aerodynamic forces and the horsepower absorbed in air drag by the protruding gun. Special attention is given to the jacket around the gun, which seems to provid… more
Date: July 1941
Creator: Luoma, Arvo A.
Partner: UNT Libraries Government Documents Department
Back to Top of Screen