5,164 Matching Results

Search Results

Flight Investigations at High-Subsonic, Transonic, and Supersonic Speeds to Determine Zero-Lift Drag of Fin-Stabilized Bodies of Revolution having Fineness Ratios of 12.5, 8.91, and 6.04 and Varying Positions of Maximum Diameter

Description: Rocket-powered models were flown at high-subsonic, transonic, and supersonic speeds to determine the zero-lift drag of fin-stabilized parabolic bodies of revolution differing in fineness ratio and in position of maximum diameter. The present paper presents the results for fineness ratio 12.5, 8.91 and 6.04 bodies having maximum diameters located at stations of 20, 40, 60, and 80 percent of body length. All configurations had cut-off sterns and all had equal base, frontal, and exposed fin areas. For most of the supersonic-speed range models having their maximum diameters at the 60-percent station gave the lowest values of drag coefficient. At supersonic speeds, increasing the fineness ratio generally reduced the drag coefficient for a given position of maximum diameter.
Date: November 30, 1949
Creator: Hart, Roger G. & Katz, Ellis R.
Partner: UNT Libraries Government Documents Department

Altitude Investigation of Gas Temperature Distribution at Turbine of Three Similar Axial-Flow Turbojet Engines

Description: An investigation of the effect of inlet pressure, corrected engine speed, and turbine temperature level on turbine-inlet gas temperature distributions was conducted on a J40-WE-6, interim J40-WE-6, and prototype J40-WE-8 turbojet engine in the altitude wind tunnel at the NACA Lewis laboratory. The engines were investigated over a range of simulated pressure altitudes from 15,000 to 55,000 feet, flight Mach numbers from 0.12 to 0.64, and corrected engine speeds from 7198 to 8026 rpm.
Date: August 6, 1952
Creator: Prince, W. R. & Schulze, F. W.
Partner: UNT Libraries Government Documents Department

Wind-Tunnel Investigation of the Low-Speed Static Stability and Control Characteristics of a Model of Bell MX-776

Description: An investigation has been made in the Langley stability tunnel to determine the low-speed static stability and control characteristics of a model of the Bell MX-776. The results of the investigation indicated that the basic model configuration was longitudinally stable in the angle-of-attack range from about -16 deg. to 16 deg. but that the stability was a minimum near O deg angle of attack. The data indicated an aerodynamic-center position about 0.64 body diameters behind the center of gravity at low angles of attack. Reduction in the size of the front horizontal fins increased the longitudinal stability. With 20 percent of the span of the normal front horizontal fins cut off the aerodynamic center was about 1.04 body diameters behind the center of gravity, and with front horizontal fins having the same area as the front vertical fins, the aerodynamic center was 2.26 body diameters behind the center of gravity (at low angles of attack).
Date: July 6, 1949
Creator: Queijo, M. J. & Michael, W. H., Jr.
Partner: UNT Libraries Government Documents Department

Summary of Low-Lift Drag and Directional Stability Data from Rocket Models of the Douglas XF4D-1 Airplane with and without External Stores and Rocket Packets at Mach Numbers from 0.8 to 1.38: TED No. NACA DE-349

Description: At the request of the Bureau of Aeronautics, Department of the Navy, an investigation at transonic and low supersonic speeds of the drag and longitudinal trim characteristics of the Douglas XF4D-1 airplane is being conducted by the Langley Pilotless Aircraft Research Division. The Douglas XF4D-1 is a jet-propelled, low-aspect-ratio, swept-wing, tailless, interceptor-type airplane designed to fly at low supersonic speeds. As a part of this investigation, flight tests were made using rocket- propelled 1/10- scale models to determine the effect of the addition of 10 external stores and rocket packets on the drag at low lift coefficients. In addition to these data, some qualitative values of the directional stability parameter C(sub n beta) and duct total-pressure recovery are also presented.
Date: July 18, 1952
Creator: Mitcham, Grady L.; Blanchard, Willard S., Jr. & Hastings, Earl C., Jr.
Partner: UNT Libraries Government Documents Department

Drag and Longitudinal Trim at Low Lift of the North American YF-100A Airplane at Mach Numbers from 0.76 to 1.77 as Determined from the Flight Test of a 0.11-Scale Rocket Model

Description: Drag and longitudinal trim at low lift of the North American YF-100A airplane at Mach numbers from 0.76 to 1.77 as determined from the flight test of a 0.11-scale rocket model are presented herein. Also included are some longitudinal stability and some qualitative pitch-damping data.
Date: May 14, 1953
Creator: Blanchard, Willard S., Jr.
Partner: UNT Libraries Government Documents Department

Calibration of the Friez Aerovane, Wind Measuring Set AN/GMQ-11

Description: Calibrations of the Friez Aerovane, Wind Measuring Set AN/GMQ-11, manufactured by the Friez Instrument Division of the Bendix Aviation Corporation, were made in the Langley 300 MPH 7- by 10-foot tunnel at the request of the Signal Corps, U, S. Army. Two propellers snd two generators were tested through a speed range of 15 to 190 knots, The results indicated that at airspeeds greater than 80 knots the instrument indicated airspeeds higher than the tunnel airspeed..
Date: December 29, 1953
Creator: McKee, John W.
Partner: UNT Libraries Government Documents Department

Investigations of Tumbling Characteristics of a 1/20-Scale Model of the Northrop N-9M Airplane

Description: From Summary: "The tumbling characteristics of a 1/20-scale model of the Northrop N-9M airplane have been determined in the Langley 20-foot free-spinning tunnel for various configurations and loading conditions of the model. The investigation included tests to determine whether recovery from a tumble could be effected by the use of parachutes. An estimation of the forces due to acceleration acting on the pilot during a tumble was made. The tests were performed at an equivalent test altitude of 15,000 feet."
Date: January 27, 1947
Creator: MacDougall, George F., Jr.
Partner: UNT Libraries Government Documents Department

Investigation of Rim Cracking in Turbine Wheels with Welded Blades

Description: Rim cracking in turbine wheels with welded blades was evaluated. The problem is explained on the basis of the occurrence of plastic flow in the rim during transient starting conditions when thermal compressive stresses resulting from high-temperature gradients exceed the proportional elastic limit of the material.
Date: February 12, 1947
Creator: Millenson, M. B. & Manson, S. S.
Partner: UNT Libraries Government Documents Department

Landing Characteristics in Waves of Three Dynamic Models of Flying Boats

Description: Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact.
Date: May 7, 1947
Creator: Benson, James M.; Havens, Robert F. & Woodward, David R.
Partner: UNT Libraries Government Documents Department

Supersonic Wave Interference Affecting Stability

Description: Some of the significant interference fields that may affect stability of aircraft at supersonic speeds are briefly summarized. Illustrations and calculations are presented to indicate the importance of interference fields created by wings, bodies, wing-body combinations, jets, and nacelles.
Date: March 8, 1958
Creator: Love, Eugene S.
Partner: UNT Libraries Government Documents Department

The Base Pressure at Supersonic Speeds on Two-Dimensional Airfoils and Bodies of Revolution (With and Without Fins) Having Turbulent Boundary Layers

Description: An analysis has been made of available experimental data to show the effects of most variables that are predominant in determining base pressure at supersonic speeds. Two dimensional bases and bases of bodies of revolution, restricted to turbulent boundary layers, are covered.
Date: April 29, 1953
Creator: Love, Eugene S.
Partner: UNT Libraries Government Documents Department

A Transonic Wind-Tunnel Investigation of a Seaplane Configuration having a 40 Deg Sweptback Wing, TED No. NACA DE 387

Description: From Summary: "During the course of an aerodynamic loads investigation of a model of the Martin XP6M-1 flying boat in the Langley 16-foot transonic tunnel, longitudinal-aerodynamic-performance information was obtained. Data were obtained at speeds up to and exceeding those anticipated for the seaplane in level flight and included the Mach number range from 0.84. to 1.09. The angle of attack was varied from -2deg to 6deg and the average Reynolds number, based on wing mean aerodynamic chord, was about 3.7 x 10(exp 6)."
Date: April 6, 1956
Creator: Hieser, Gerald; Kudlacik, Louis & Gray, W. H.
Partner: UNT Libraries Government Documents Department

Ditching Tests of a 1/8-Scale Model of the Chance Vought XF6U-1 Airplane, TED No. NACA DE319

Description: Tests were made with a 1/8-scale dynamically similar model of the Chance Vought XF6U-1 airplane to study its behavior when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated. The behavior of the model was determined from visual observations, by recording time histories of the accelerations, and by taking motion pictures of the ditchings. From the results of the tests it was concluded that the airplane should be ditched at the near-stall, tail-down attitude (12 deg). The flaps should be fully extended to obtain the lowest possible landing speed. The wing-tip tanks should be jettisoned. The underside of the fuselage will be critically damaged in a ditching and the airplane will dive violently after a run of about three fuselage lengths. Maximum longitudinal decelerations up to about 7g and maximum vertical accelerations up to about 5g will be encountered.
Date: January 19, 1948
Creator: Fisher, Lloyd J., Jr. & McBride, Ellis E.
Partner: UNT Libraries Government Documents Department

Flight Tests of Rocket-Powered "Tin-Can" Models of AAF Project MX-800

Description: Flight tests were made of six noninstrumented rocket-powered "Tin Can" models of AAF Project MX-800. Velocity and drag data were obtained by use of CU Doppler radar. The existence of stability and adequate structural strength for flight near zero lift was checked by visual and photographic observation. Drag data obtained during the tests agreed reasonably well with estimates based on experimental data from NACA RM-2 rocket-powered drag research models.
Date: December 1, 1947
Creator: Purser, Paul E. & Stone, David G.
Partner: UNT Libraries Government Documents Department

Rocket-Model Measurements of Zero-Lift Damping in Roll of the Bell MX-776 Missile at Mach Numbers from 0.6 to 1.56

Description: The zero-lift damping in roll of the Bell MX-776 missile has been measured by a sting-mounted rocket-model technique at Mach numbers from 0.6 to 1.56. The damping-in-roll data, in general, show no unusual variation with Mach number. Aileron rolling-moment effectiveness derived from these data and previously obtained rolling-effectiveness data appear reasonable,.
Date: December 31, 1953
Creator: Bland, William M., Jr. & Purser, Paul E.
Partner: UNT Libraries Government Documents Department

Altitude-Wind-Tunnel Investigation of a 4000-Pound-Thrust Axial-Flow Turbojet Engine, 5, Analysis of Turbine Performance

Description: From Summary: "Performance characteristics of the turbine of a 4000-pound-thrust axial-flow turbojet engine was determined in investigations of the complete engine in the NACA Cleveland altitude wind tunnel. Characteristics are presented as functions of the total-pressure ratio across the turbine and of turbine speed and gas flow corrected to sea-level conditions. Three turbine nozzles of different areas were used to determine the area that gave optimum performance. Inasmuch as tail-pipe nozzles of different diameters were investigated in combination with the standard turbine nozzle, the effect of varying discharge conditions on turbine operation could be observed."
Date: August 4, 1948
Creator: Krebs, Richard P. & Hensley, Reece V.
Partner: UNT Libraries Government Documents Department

Wind-Tunnel Tests of a 0.16-Scale Model of the Douglas MX-656 Airplane at High Subsonic Speeds, 1, Stability and Control Characteristics

Description: Wind tunnel tests of the 0.16-scale Douglas MX-656 model were made at low and high subsonic Mach numbers to investigate the static longitudinal- and lateral stability characteristics. The tests shows that undesirable changes in longitudinal stability at the stall were apparently caused by an altered downwash pattern at the tail. The jettisonable nose fins were highly destabilizing. Compressibility effects for the test Mach numbers were not detrimental to the longitudinal- or lateral-stability characteristics.
Date: April 26, 1949
Creator: Hamilton, William T. & Cleary, Joseph W.
Partner: UNT Libraries Government Documents Department

Wind-Tunnel Tests of a 0.16-Scale Model of the Douglas MX-656 Airplane at High Subsonic Speeds. 2 - Wing and Fuselage Pressure Distribution

Description: From Summary: "Measurements of wing and fuselage pressure distributions were made at low and high subsonic Much numbers on a 0.16-scale model of the projected MX-656 research airplane. The MX-656 is a supersonic design utilizing a low-aspect-ratio wing and tail. Pressure-distribution measurements indicated that, although the critical Mach number of the wing was approximately 0.81 at 0 degree angle of attack, compressibility effects were of little significance below a Mach number of at least 0.90. The principal effect of compressibility was an increase in the pressure gradient over the after 30 percent of the wing chord, causing a tendency for the flow to separate."
Date: August 22, 1949
Creator: Cleary, Joseph W. & Mellenthin, Jack A.
Partner: UNT Libraries Government Documents Department

An Investigation of the Aerodynamic Characteristics in Pitch of an XB-52 Airplane Model in a High-Speed Wind Tunnel

Description: From Summary: "A wind-tunnel investigation of a 0.049-scale model of the Boeing XB-52 airplane was made at Mach numbers from 0.30 to 0.925 and at corresponding Reynolds numbers from about 2.3 x 10(exp 6) to 4.3 x 10(exp 6). The results of the investigation indicate satisfactory static longitudinal stability throughout the test Mach-number range and some loss in tail effectiveness beginning at about 0.80 Mach number. A comparison of the results of these tests with those of the same model in the Boeing Airplane Company's wind tunnel showed close agreement of lift- and drag-divergence Mach numbers. Slight differences were observed in tail effectiveness and the position of the stick-fixed neutral point."
Date: March 16, 1951
Creator: Cleary, Joseph W. & Coe, Charles F.
Partner: UNT Libraries Government Documents Department

High-Speed Cascade Tests of the NACA 65-(12A(sub 10))10 and NACA 65-(12A(sub 2)I(sub 8b))10 Compressor Blade Sections

Description: From Summary: "Two-dimensional porous-well cascade tests of the NACA 65- (l2Al0) 10 and NACA 65-(l2A2I8b)10 blade sections were made at Mach numbers from 0.3 to choking in most cases. Data were obtained at solidities of 1.0 and 1.5 at inlet-air angles of 45 deg. and 60 deg. for both blade sections. With a solid--wall modification to the cascade tunnel, schlieren observations were made of the flow in cascade at a solidity of 1.5 and inlet-air angle of 45 deg. and at a solidity of 1.0 and inlet-air angle of 60 deg."
Date: December 21, 1955
Creator: Dunavant, James C.; Emery, James C.; Walch, Howard C. & Westphal, Willard R.
Partner: UNT Libraries Government Documents Department

Stick-Fixed Stability and Control Characteristics of the Consolidated Vultee Model 240 Airplane as Estimated from Tests of a 0.092-Scale Powered Model

Description: From Summary: "Estimates of the static stick-fixed stability and control characteristics of the Consolidated Vultee model 240 airplane are presented in this report. The estimates are based on tests of a 0.092-scale powered model in the 10-foot wind tunnel of the Guggenheim Aeronautical Laboratory of the California Institute of Technology. Results of the analysis are evaluated in terms of the Army specifications for stability and control characteristics which are more specific and, in general, equal to or more rigid than the Civil Aeronautics Administration requirements."
Date: June 27, 1947
Creator: McCullough, George B.; Weiberg, James A. & Gault, Donald E.
Partner: UNT Libraries Government Documents Department

Flight Comparison of Performance and Cooling Characteristics of Exhaust-Ejector Installation with Exhaust-Collector-Ring Installation

Description: Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.
Date: February 14, 1947
Creator: Acker, Loren W. & Kleinknecht, Kenneth S.
Partner: UNT Libraries Government Documents Department

Investigation of a Half-Conical Scoop Inlet Mounted at Five Alternate Circumferential Locations Around a Circular Fuselage: Pressure-Recovery Results at a Mach Number 2.01

Description: The effects of inlet circumferential position around the fuselage on the characteristics of a half-conical scoop inlet having a 24.6deg half-angle cone have been investigated in the langley 4- by 4-foot supersonic pressure tunnel. Pressure-recovery results have been obtained at a Mach number of 2.01 for a fixed boundary-layer-bleed height which was 60 percent of the boundary-layer thickness at an angle of attack of 0deg, and for cowling position parameters of 42.4deg and 38.0deg. inlet had a capture area equal to 24.9 percent of the basic-fuselage frontal area. The angle of attack was varied from 0deg to 12deg.
Date: June 30, 1953
Creator: Hasel, Lowell E.; Lankford, John L. & Robins, A. W.
Partner: UNT Libraries Government Documents Department