887 Matching Results

Search Results

Reinjection laser oscillator and method

Description: A uv preionized CO/sub 2/ oscillator with integral four-pass amplifier capable of providing 1 to 5 GW laser pulses with pulse widths from 0.1 to 0.5 ns full width at half-maximum (FWHM) is described. The apparatus is operated at any pressure from 1 atm to 10 atm without the necessity of complex high voltage electronics. The reinjection technique employed gives rise to a compact, efficient system that is particularly immune to alignment instabilities with a minimal amount of hardware and complexity.
Date: August 20, 1981
Creator: McLellan, E.J.
Partner: UNT Libraries Government Documents Department

Improved method for the production of atomic ion species from plasma ion sources

Description: A technique to enhance the yield of neutral atomic and ionic species (H{sup +}, D{sup +}, O{sup +}, N{sup +}, etc.) from plasmas. The technique involves the addition of catalyzing agents to the ion discharge. Effective catalysts include H{sub 2}O, O{sub 2}, and SF{sub 6}, among others, with the most effective being water (H{sub 2}O). This technique has been developed at Argonne National Laboratory, where microwave produced beams consisting essentially of 100% atomic neutral species (H) have been generated, and ion beams of close to 100% purity have been generated.
Date: December 31, 1996
Creator: Spence, D. & Lykke, K.
Partner: UNT Libraries Government Documents Department

Catalysts for Conversion of Methane to Higher Hydrocarbons

Description: Catalysts for converting methane to higher hydrocarbons such as ethane and ethylene in the presence of oxygen at temperatures in the range of about 700 to 900{degrees}C are described. These catalysts comprise calcium oxide or gadolinium oxide respectively promoted with about 0.025--0.4 mole and about 0.1--0.7 mole sodium pyrophosphate. A preferred reaction temperature in a range of about 800 to 850{degrees}C with a preferred oxygen-to-methane ratio of about 2:1 provides an essentially constant C{sub 2} hydrocarbon yield in the range of about 12 to 19 percent over a period of time greater than about 20 hours.
Date: May 15, 1991
Creator: Siriwardane, Ranjani V.
Partner: UNT Libraries Government Documents Department

Improved catalysts and method

Description: An improved catalyst and method for the oxyhydrochlorination of methane is disclosed. The catalyst includes a pyrogenic porous support on which is layered as active material, cobalt chloride in major proportion, and minor proportions of an alkali metal chloride and of a rare earth chloride. On contact of the catalyst with a gas flow of methane, HCl and oxygen, more than 60% of the methane is converted and of that converted more than 40% occurs as monochloromethane. Advantageously, the monochloromethane can be used to produce gasoline boiling range hydrocarbons with the recycle of HCl for further reaction. This catalyst is also of value for the production of formic acid as are analogous catalysts with lead, silver or nickel chlorides substituted for the cobalt chloride. 8 figs., 3 tabs.
Date: December 31, 1990
Creator: Taylor, C. E. & Noceti, R. P.
Partner: UNT Libraries Government Documents Department

Method for distinguishing normal and transformed cells using G1 kinase inhibitors

Description: A G{sub 1} phase kinase inhibitor is applied in a low concentration to a population of normal and transformed mammalian cells. The concentration of G{sub 1} phase kinase inhibitor is selected to reversibly arrest normal mammalian cells in the G{sub 1} cell cycle without arresting growth of transformed cells. The transformed cells may then be selectively identified and/or cloned for research or diagnostic purposes. The transformed cells may also be selectively killed by therapeutic agents that do not affect normal cells in the G{sub 1} phase, suggesting that such G{sub 1} phase kinase inhibitors may form an effective adjuvant for use with chemotherapeutic agents in cancer therapy for optimizing the killing dose of chemotherapeutic agents while minimizing undesirable side effects on normal cells.
Date: December 31, 1991
Creator: Crissman, H. A.; Gadbois, D. M.; Tobey, R. A. & Bradbury, E. M.
Partner: UNT Libraries Government Documents Department

1-/sup 11/C-D-glucose and related compounds

Description: The novel compounds 1-/sup 11/C-D-glucose, 1-/sup 11/C-D-mannose, 1-/sup 11/C-D-galactose, 2-/sup 11/C-D-glucose, 2-/sup 11/C-D-mannose and 2-/sup 11/C-D-galactose which can be used in nuclear medicine to monitor the metabolism of glucose and galactose can be rapidly prepared by reaction of the appropriate aldose substrate with an alkali metal /sup 11/C-labeled cyanide followed by reduction with a Raney alloy in formic acid.
Date: January 26, 1982
Creator: Shiue, Chyng-Yann & Wolf, Alfred P.
Partner: UNT Libraries Government Documents Department

Low Loss Composition of BA{sub X}SR{sub Y}CA{sub 1-X-Y}TIO{sub 3}:BA{sub 0.12-0.25}SR{sub 0.35-0.47}CA{sub 0.32-0.53}TIO{sub 3}

Description: A dielectric thin-film material for microwave applications, including use as a capacitor, the thin-film comprising a composition of barium strontium calcium and titanium of perovskite type (Ba{sub x}Sr{sub y}Ca{sub 1-x-y})TiO{sub 3}. Also provided is a method for making a dielectric thin film of that formula over a wide compositional range through a single deposition process.
Date: October 19, 1999
Creator: Xiang, Xiao-Dong; Chang, Hauyee & Takeuchi, Ichiro
Partner: UNT Libraries Government Documents Department

Interline transfer CCD camera

Description: An interline CCD sensing device for use in a camera system, includes an imaging area sensitive to impinging light, for generating charges corresponding to the intensity of the impinging light. Sixteen independent registers R1 - R16 sequentially receive the interline data from the imaging area, corresponding to the generated charges. Sixteen output amplifiers S1 - S16 and sixteen ports P1 - P16 for sequentially transferring the interline data, one pixel at a time, in order to supply a desired image transfer speed. The imaging area is segmented into sixteen independent imaging segments A1 - A16, each of which corresponds to one register, on output amplifier, and one output port. Each one of the imaging segments A1 - A16 includes an array of rows and columns of pixels. Each pixel includes a photogate area, an interline CCD channel area, and an anti-blooming area. The anti-blooming area is, in turn, divided into an anti-blooming barrier and an anti-blooming drain.
Date: December 31, 1993
Creator: Prokop, M.S.; McCurnin, T.W.; Stump, C.J. & Stradling, G.L.
Partner: UNT Libraries Government Documents Department

One-piece, composite crucible with integral withdrawal/discharge section

Description: A one-piece, composite open-bottom casting mold with integral withdrawal section is fabricated by thermal spraying of materials compatible with and used for the continuous casting of shaped products of reactive metals and alloys such as, for example, titanium and its alloys or for the gas atomization thereof.
Date: July 30, 2002
Creator: Besser, Matthew; Terpstra, Robert L. (Iowa State Univ., Ames, IA); Sordelet, Daniel J.; Anderson, Iver E.; Hartman, Alan D.; Argetsinger, Edward R. et al.
Partner: UNT Libraries Government Documents Department

Liquid scintillators for optical-fiber applications

Description: A multicomponent liquid scintillator solution for use as a radiation-to-light converter in conjunction with a fiber optic transmission system. The scintillator includes a quantity of 1, 2, 4, 5, 3H, 6H, 1 OH, tetrahydro-8-trifluoromethyl (1) benzopyrano (9, 9a, 1-gh) quinolizin-10-one (Coumarin) as a solute in a fluor solvent such as benzyl alcohol or pseudo-cumene. The use of BIBUQ as an additional or primary solute is also disclosed.
Date: June 1, 1981
Creator: Franks, L.A. & Lutz, S.S.
Partner: UNT Libraries Government Documents Department

Oxygen-stabilized zirconium-vanadium-iron alloy

Description: An oxygen stabilized intermetallic compound is described which has the formula (Zr/sub 1-x/Ti/sub x/)/sub 2-u/(V/sub 1-y/Fe/sub y/)O/sub z/ where x = 0.0 to 0.9, y = 0.01 to 0.9, z = 0.25 to 0.5 and u = 0 to 1. The compound is capable of reversibly sorbing hydrogen at temperatures from -196/sup 0/C to 200/sup 0/C at pressures down to 10/sup -8/ torr. The compound is suitable for use as a hydrogen getter in low pressure, high temperature applications such as magnetic confinement fusion devices.
Date: June 16, 1981
Creator: Mendelsohn, M H & Gruen, D M
Partner: UNT Libraries Government Documents Department

Pressure gradient passivation of carbonaceous material normally susceptible to spontaneous combustion

Description: This invention is a process for the passivation or deactivation with respect to oxygen of a carbonaceous material by the exposure of the carbonaceous material to an oxygenated gas in which the oxygenated gas pressure is increased from a first pressure to a second pressure and then the pressure is changed to a third pressure. Preferably a cyclic process which comprises exposing the carbonaceous material to the gas at low pressure and increasing the pressure to a second higher pressure and then returning the pressure to a lower pressure is used. The cycle is repeated at least twice wherein the higher pressure may be increased after a selected number of cycles.
Date: January 29, 2002
Creator: Ochs, Thomas L.; Sands, William D.; Schroeder, Karl; Summers, Cathy A. & Utz, Bruce R.
Partner: UNT Libraries Government Documents Department

Method of making multilayered titanium ceramic composites

Description: A method making a titanium ceramic composite involves forming a hot pressed powder body having a microstructure comprising at least one titanium metal or alloy layer and at least one ceramic particulate reinforced titanium metal or alloy layer and hot forging the hot pressed body follwed by hot rolling to substantially reduce a thickness dimension and substantially increase a lateral dimension thereof to form a composite plate or sheet that retains in the microstructure at least one titanium based layer and at least one ceramic reinforced titanium based layer in the thickness direction of the composite plate or sheet.
Date: August 25, 1998
Creator: Fisher, George T., II; Hansen; S., Jeffrey; Oden; L., Laurance; Turner et al.
Partner: UNT Libraries Government Documents Department

Apparatus and Method for Increasing the Diameter of Metal Alloy Wires Within a Molten Metal Pool

Description: In a dip forming process the core material to be coated is introduced directly into a source block of coating material eliminating the need for a bushing entrance component. The process containment vessel or crucible is heated so that only a portion of the coating material becomes molten, leaving a solid portion of material as the entrance port of, and seal around, the core material. The crucible can contain molten and solid metals and is especially useful when coating core material with reactive metals. The source block of coating material has been machined to include a close tolerance hole of a size and shape to closely fit the core material. The core material moves first through the solid portion of the source block of coating material where the close tolerance hole has been machined, then through a solid/molten interface, and finally through the molten phase where the diameter of the core material is increased. The crucible may or may not require water-cooling depending upon the type of material used in crucible construction. The system may operate under vacuum, partial vacuum, atmospheric pressure, or positive pressure depending upon the type of source material being used.
Date: January 29, 2002
Creator: Hartman, Alan D.; Argetsinger, Edward R.; Hansen, Jeffrey S.; Paige, Jack I.; King, Paul E. & Turner, Paul C.
Partner: UNT Libraries Government Documents Department

Compression Stripping of Flue Gas with Energy Recovery

Description: A method of remediating and recovering energy from combustion products from a fossil fuel power plant having at least one fossil fuel combustion chamber, at least one compressor, at least one turbine, at least one heat exchanger and a source of oxygen. Combustion products including non-condensable gases such as oxygen and nitrogen and condensable vapors such as water vapor and acid gases such as SO<sub>X</sub> and NO<sub>X</sub> and CO<sub>2</sub> and pollutants are produced and energy is recovered during the remediation which recycles combustion products and adds oxygen to support combustion. The temperature and/or pressure of the combustion products are changed by cooling through heat exchange with thermodynamic working fluids in the power generation cycle and/or compressing and/or heating and/or expanding the combustion products to a temperature/pressure combination below the dew point of at least some of the condensable vapors to condense liquid having some acid gases dissolved and/or entrained and/or directly condense acid gas vapors from the combustion products and to entrain and/or dissolve some of the pollutants while recovering sensible and/or latent heat from the combustion products through heat exchange between the combustion products and thermodynamic working fluids and/or cooling fluids used in the power generating cycle. Then the CO<sub>2</sub>, SO<sub>2</sub>, and H<sub>2</sub>O poor and oxygen enriched remediation stream is sent to an exhaust and/or an air separation unit and/or a turbine.
Date: May 31, 2005
Creator: Ochs, Thomas L. & O'Connor, William K.
Partner: UNT Libraries Government Documents Department

Method for making devices having intermetallic structures and intermetallic devices made thereby

Description: A method and system for making a monolithic intermetallic structure are presented. The structure is made from lamina blanks which comprise multiple layers of metals which are patternable, or intermetallic lamina blanks that are patternable. Lamina blanks are patterned, stacked and registered, and processed to form a monolithic intermetallic structure. The advantages of a patterned monolithic intermetallic structure include physical characteristics such as melting temperature, thermal conductivity, and corrosion resistance. Applications are broad, and include among others, use as a microreactor, heat recycling device, and apparatus for producing superheated steam. Monolithic intermetallic structures may contain one or more catalysts within the internal features.
Date: January 6, 2004
Creator: Paul, Brian Kevin; Wilson, Rick D. & Alman, David E.
Partner: UNT Libraries Government Documents Department

Water and UV degradable lactic acid polymers

Description: A water and UV light degradable copolymer of monomers of lactic acid and a modifying monomer selected from the class consisting of ethylene and polyethylane glycols (PVB 6/22/90), propylene and and polypropylene (PVB 6/22/90) glycols, P-dioxanone, 1, 5 dioxepan-2-one, 1,4 -oxathialan-2-one, 1,4-dioxide and mixtures thereof. These copolymers are useful for waste disposal and agricultural purposes. Also disclosed is a water degradable blend of polylactic acid or modified polylactic acid and high molecular weight polyethylene oxide wherein the high molecular weight polyethylene oxide is present in the range of from about 2% by weight to about 50% by weight, suitable for films. A method of applying an active material selected from the class of seeds, seedlings, pesticides, herbicides, fertilizers and mixtures thereof to an agricultural site is also disclosed.
Date: June 26, 1990
Creator: Bonsignore, P. V. & Coleman, R. D.
Partner: UNT Libraries Government Documents Department

Plutonium dissolution process

Description: A two-step process for dissolving Pu metal is disclosed in which two steps can be carried out sequentially or simultaneously. Pu metal is exposed to a first mixture of 1.0-1.67 M sulfamic acid and 0.0025-0.1 M fluoride, the mixture having been heated to 45-70 C. The mixture will dissolve a first portion of the Pu metal but leave a portion of the Pu in an oxide residue. Then, a mineral acid and additional fluoride are added to dissolve the residue. Alternatively, nitric acid between 0.05 and 0.067 M is added to the first mixture to dissolve the residue as it is produced. Hydrogen released during the dissolution is diluted with nitrogen.
Date: January 1, 1994
Creator: Vest, Michael A.; Fink, Samuel D.; Karraker, David G.; Moore, Edwin N. & Holcomb, H. Perry
Partner: UNT Libraries Government Documents Department

Method for processing aluminum spent potliner in a graphite electrode arc furnace

Description: A method of processing spent aluminum pot liner containing carbon, cyanide compositions, fluorides and inorganic oxides. The spend aluminum pot liner is crushed, iron oxide is added to form an agglomerated material. The agglomerated material is melted in an electric arc furnace having the electrodes submerged in the molten material to provide a reducing environment during the furnace operation. In the reducing environment, pot liner is oxidized while the iron oxides are reduced to produce iron and a slag substantially free of cyanide compositions and fluorides. An off-gas including carbon oxides and fluorine is treated in an air pollution control system with an afterburner and a scrubber to produce NaF, water and a gas vented to the atmosphere free of cyanide compositions, fluorine, and CO.
Date: December 24, 2002
Creator: O'Connor, William K.; Turner, Paul C. & Addison, G.W. (AJT Enterprises, Inc.)
Partner: UNT Libraries Government Documents Department

A method to remove Ammonia using a Proton-Conducting Ceramic Membrane

Description: An apparatus and method for decomposing NH{sub 3}. A fluid containing NH{sub 3} is passed in contact with a tubular membrane that is a homogeneous mixture of a ceramic and a first metal, with the ceramic being selected from one or more of a cerate having the formula of M' Ce{sub 1-x} M''O{sub 3-{delta}}, zirconates having the formula M'Zr{sub 1-x} M''3-{delta}, stannates having the formula M'Sn{sub 1-x}M''O{sub 3}-{delta}, where M' is a group IIA metal, M'' is a dopant metal of one or more of Ca, Y, Yb, In, Nd, Gd or mixtures thereof and {delta} is a variable depending on the concentration of dopant and is in the range of from 0.001 to 0.5, the first metal is a group VIII or group IB element selected from the group consisting of Pt, Ag, Pd, Fe, Co, Cr, Mn, V, Ni, Au, Cu, Rh, Ru and mixtures thereof. The tubular membrane has a catalytic metal on the side thereof in contact with the fluid containing NH{sub 3} which is effective to cause NH{sub 3} to decompose to N{sub 2} and H{sub 2}. When the H{sub 2} contacts the membrane, H{sup +} ions are formed which pass through the membrane driving the NH{sub 3} decomposition toward completion.
Date: September 22, 1999
Creator: Balachandran, Uthamalingam & Bose, Arun C.
Partner: UNT Libraries Government Documents Department

Electrochemical storage cell containing a substituted anisole or di-anisole redox shuttle additive for overcharge protection and suitable for use in liquid organic and solid polymer electrolytes

Description: A electrochemical cell is described comprising an anode, a cathode, a solid polymer electrolyte; and a redox shuttle additive to protect the cell against overcharging and a redox shuttle additive to protect the cell against overcharging selected from the group consisting of: (a) a substituted anisole having the general formula shown in a figure (in an uncharged state): where R{sub 1} is selected from the group consisting of H, 0CH{sub 3}, OCH{sub 2}CH{sub 3}, and OCH{sub 2}phenyl, and R{sub 2} is selected from the group consisting of OCH{sub 3}, OCH{sub 2}CH{sub 3}, OCH{sub 2} phenyl, and O{sup {minus}}Li{sup +}; and (b) a di-anisole compound having the general formula shown in a second figure (in an uncharged state): where R is selected from the group consisting of -OCH{sup 3} and -CH{sub 3}, m is either 1 or 0, n is either 1 or 0, and X is selected from the group consisting of -OCH{sub 3} (methoxy) or its lithium salt -O{sup {minus}}Li{sup +}. The lithium salt of the di-anisole is the preferred form of the redox shuttle additive because the shuttle anion will then initially have a single negative charge, it loses two electrons when it is oxidized at the cathode, and then moves toward the anode as a single positively charged species where it is then reduced to a single negatively charged species by gaining back two electrons.
Date: March 1998
Creator: Kerr, John B. & Tian, Minmin
Partner: UNT Libraries Government Documents Department

Photosensitivity enhancement of PLZT ceramics by positive-ion implantation

Description: The photosensitivity of lead lanthanum zirconate titanate (PLZT) ceramic material used in high resolution, high contrast, and nonvolatile photoferroelectric image storage and display devices is enhanced significantly by positive ion implantation of the PLZT near its surface. Implanted ions include H/sup +/, He/sup +/, Ne/sup +/, Ar/sup +/, as well as chemically reactive ions from Fe, Cr, and Al. The positive ion implantation advantageously serves to shift the absorption characteristics of the PLZT material from near-uv light to visible light. As a result, photosensitivity enhancement is such that the positive ion implanted PLZT plate is sensitive even to sunlight and conventional room lighting, such as fluorescent and incandescent light sources. The method disclosed includes exposing the PLZT plate to the positive ions at sufficient density, from 1 x 10/sup 12/ to 1 x 10/sup 17/, and with sufficient energy, from 100 to 500 keV, to provide photosensitivity enhancement. The PLZT material may have a lanthanum content ranging from 5 to 10%, a lead zirconate content of 62 to 70 mole %, and a lead titanate content of 38 to 30%. The ions are implanted at a depth of 0.1 to 2 microns below the surface of the PLZT plate.
Date: January 28, 1982
Creator: Peercy, P.S. & Land, C.E.
Partner: UNT Libraries Government Documents Department

Eliminating livelock in flushable routing networks

Description: This invention is comprised of a method for livelock-free message routing is provided in a network of interconnected nodes that is flushable in time T. An input message processor generates sequences of at least N time intervals, each of duration T. An input register provides for receiving and holding each input message, where the message is assigned a priority state p during an nth one of the N time intervals. At each of the network nodes a message processor reads the assigned priority state and awards priority to messages with priority state (p-1) during an nth time interval and to messages with priority state p during an (n + 1)th time interval. The messages that are awarded priority are output on an output path toward the addressed output message processor. Thus, no message remains in the network for a time longer than T.
Date: December 31, 1992
Creator: Faber, V.
Partner: UNT Libraries Government Documents Department

Reflective Optical Imaging System for Extreme Ultraviolet Wavelengths

Description: This invention is comprised of a projection reflection optical system having two mirrors in a coaxial, four reflection configuration to reproduce the image of an object. The mirrors have aspherical reflection surfaces to provide a very high resolution of object feature wavelengths less than 200 {mu}m, and preferably less than 100 {mu}m. An image resolution of features less than 0.05--0.1 {mu}m, is obtained over a large area field; i.e., 25.4 mm {times} 25.4 mm, with a distortion less than 0.1 of the resolution over the image field.
Date: December 31, 1991
Creator: Viswanathan, V. K. & Newnam, B. E.
Partner: UNT Libraries Government Documents Department