369 Matching Results

Search Results

Advanced search parameters have been applied.

Pressure-sensitive system for gas-temperature control

Description: From Summary: "A thermodynamic relation is derived and simplified for use as a temperature-limiting control equation involving measurement of gas temperature before combustion and gas pressures before and after combustion. For critical flow in the turbine nozzles of gas-turbine engines, the control equation is further simplified to require only measurements upstream of the burner. Hypothetical control systems are discussed to illustrate application of the control equations."
Date: March 4, 1948
Creator: Cesaro, Richard S. & Matz, Norman
Partner: UNT Libraries Government Documents Department

Investigation and Preparation of Polymer Films to Improve the Separation of Water and Salts in Saline Water Conversion

Description: From Introduction: "As will be explained in more detail elsewhere in this report, casting methods and drying conditions have been found to have a drastic effect on film permeability to both water and salt. Errors that became evident in temperature control indicated that some of the previous high rates were obtained at temperatures considerably higher than the 100 degrees C that was intended and reported."
Date: December 1962
Creator: Monsanto Research Corporation
Partner: UNT Libraries Government Documents Department

Temperature-control study of turbine region of turbojet engine, including turbine-blade time constants and starting characteristics

Description: Report presenting an investigation of a turbojet engine in an altitude test facility to supplement existing data relevant to gas-temperature control in a turbojet engine. The problems associated with gas-temperature control for minimizing turbine-blade damage are considered in the report.
Date: April 25, 1956
Creator: Phillips, W. E., Jr.
Partner: UNT Libraries Government Documents Department

Low-Voltage Room Thermostat Performance

Description: Report issued by the National Bureau of Standards over low voltage electric thermostats. Thermostat test results are discussed. This report includes illustrations, and photographs.
Date: April 1983
Creator: Kao, James Y.; Sushinsky, George; Didion, David A.; Mastascusa, E. J. & Chi, Joseph
Partner: UNT Libraries Government Documents Department

Direct-Write Precision Resistors for Ceramic Packages

Description: A direct-write approach to f abricate high precision resistors is reported. Special attention is paid to the effect of print thickrw;s on the resistance value of buried resistors after a low temperature co-firing process. The results show that the direct-write approach provides a superior line definition and thickness control over a traditional screen printing process. Microstructural analysis indicates that there is an interdiffused layer developed between the resistor material and the low temperature co-fired ceramic substrate. These observations are consistent with electrical IIH.SUKHIlentS which show that resistance increases as the effective cross-sectional area is reduced. Th: resistance data show that the standard deviations for resistors printed on a 6" x 6" area are 59Z0 and 15$Z0 for the direct-write and the screen-printed patterns, respectively.
Date: November 30, 1998
Creator: Dai, S.; Dimos, D.; Huang, R.F.; Rodriguez, M.A.; Wilcox, D. & Yang, P.
Partner: UNT Libraries Government Documents Department

Undulator Changes Due to Temperature Excursions

Description: The temperature of the LCLS undulators has not been controlled during storage. The effects of the temperature excursions are documented in this note. After a number of LCLS undulators were tuned, fiducialized, and placed in storage anticipating their use, a test was made to ensure that their properties had not changed. The test revealed, however, that indeed the undulators had changed. Detailed study of this problem followed. We now believe that the gap of the undulators changes permanently when the undulators go through temperature excursions. We have tested the other possible cause, transportation, and do not see gap changes. In this note, we document how the undulators have changed since they were originally tuned. The undulators were tuned and fiducialized in the Magnetic Measurement Facility (MMF). Afterward, many of them (approximately 18) were taken to building 750 for storage during summer and fall 2007. Building 750 had no temperature control. The undulator temperatures went from 20 C, used for tuning, down to approximately 11 C during the winter. In January 2008, three of the undulators were brought back to the MMF for a check. All three undulators showed similar changes. Trajectories, phases, and most undulator properties stayed the same, but the fiducialization (beam axis position relative to tooling balls on the undulator) had changed. Further investigation showed that the undulator gap was altered in a periodic way along the magnetic axis with a net average gap change causing the fiducialization change. A new storage location in building 33 was found and future undulators were placed there. A failure in the temperature control, however, caused the undulators to get too hot. Again the gap changed, but with a different periodic pattern. This note documents the measured changes in the undulators. In particular, it shows the detailed history of undulator 39 which ...
Date: November 17, 2010
Creator: Wolf, Zachary; Levashov, Yurii & Reese, Ed
Partner: UNT Libraries Government Documents Department

Deprotection blue in extreme ultraviolet photoresists: influence of base loading and post-exposure bake temperture

Description: The deprotection blur of Rohm and Haas XP 5435, XP 5271, and XP5496 extreme ultraviolet photoresists has been determined as their base weight percent is varied. They have also determined the deprotection blur of TOK EUVR P1123 photoresist as the post-exposure bake temperature is varied from 80 C to 120 C. In Rohm and Haas XP 5435 and XP5271 resists 7x and 3x (respective) increases in base weight percent reduce the size of successfully patterned 1:1 line-space features by 16 nm and 8 nm with corresponding reductions in deprotection blur of 7 nm and 4 nm. In XP 5496 a 7x increase in base weight percent reduces the size of successfully patterned 1:1 line-space features from 48 nm to 38 nm without changing deprotection blur. In TOK EUVR P1123 resist, a reduction in post-exposure bake temperature from 100 C to 80 C reduces deprotection blur from 21 nm to 10 nm and reduces patterned LER from 4.8 nm to 4.1 nm.
Date: June 2, 2008
Creator: Anderson, Christopher N. & Naulleau, Patrick P.
Partner: UNT Libraries Government Documents Department

Stabilizer for Temperature Control Equipment

Description: From abstract: "A simple electronic circuit is described, the use of which greatly improves the temperature regulations obtainable with Beta equipment. The circuit utilizes the time derivative of the temperature to counteract oscillation and overshoot. No other changes are required in existing equipment for installation of the stabilizer."
Date: May 14, 1945
Creator: Macleish, K. G. & Palmer, R. C.
Partner: UNT Libraries Government Documents Department

Microprocessor sampled data process controller

Description: A micro-miniaturized digital processor was utilized in the development of a sampled data process controller. While general purpose in nature, the processor was applied specifically to control temperature. Physically, the processor was found to be well suited for industrial environments, as its relatively slow speed and high switching voltage levels made it exceptionally noise immune. Successful application was found to be more dependent on external software development support than anything else. This is because of the very limited nature of the processor in terms of memory and input -- output peripherals. (auth)
Date: November 1, 1973
Creator: Seim, T.A.
Partner: UNT Libraries Government Documents Department

Biofeedback and Control of Skin Cell Proliferation in Psoriasis

Description: The present study was designed to determine the effect of skin-temperature-biofeedback training on cellular proliferation in three psoriasis patients. It was hypothesized that (a) psoriasis patients would be able to consciously decrease skin temperature of psoriatic tissue, and (b) there would be a positive correlation between rate of cellular proliferation and temperature change. Results obtained indicated biofeedback training to be effective in decreasing the surface temperature of psoriatic tissue. A 2 X 7 analysis of variance for two repeated measures indicated the change in skin temperatures as a function of sample period to be significant, F (6,26) = 3.29, p < .02. Generalization of temperature-training effects from the biofeedback to the no-feedback condition were observed. Rate of proliferation decreased from pretraining to posttraining biopsies.
Date: December 1977
Creator: Benoit, Larry J.
Partner: UNT Libraries

Thermal Imaging Control of Furnaces and Combustors

Description: The object if this project is to demonstrate and bring to commercial readiness a near-infrared thermal imaging control system for high temperature furnaces and combustors. The thermal imaging control system, including hardware, signal processing, and control software, is designed to be rugged, self-calibrating, easy to install, and relatively transparent to the furnace operator.
Date: February 28, 2003
Creator: Rue, David M.; Zelepouga, Serguei & Puri, Ishwar K.
Partner: UNT Libraries Government Documents Department

Preoperational test report, recirculation condenser cooling systems

Description: This represents a preoperational test report for Recirculation Condenser Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The four system provide condenser cooling water for vapor space cooling of tanks AY1O1, AY102, AZ1O1, AZ102. Each system consists of a valved piping loop, a pair of redundant recirculation pumps, a closed-loop evaporative cooling tower, and supporting instrumentation; equipment is located outside the farm on concrete slabs. Piping is routed to the each ventilation condenser inside the farm via below-grade concrete trenches. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.
Date: November 4, 1997
Creator: Clifton, F.T.
Partner: UNT Libraries Government Documents Department

Project W-320, 241-C-106 sluicing master calculation list

Description: This supporting document has been prepared to make the Master Calculation List readily retrievable. The list gives the status of the calculation (as-built, not used, applied, etc.), the calculation title, its originator, comments, and report number under which it was issued. Tank 241-C-106 has been included on the High Heat Load Watch List.
Date: August 7, 1998
Creator: Bailey, J.W.
Partner: UNT Libraries Government Documents Department

Preoperational test report, recirculation ventilation systems

Description: This represents a preoperational test report for Recirculation Ventilation Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system provides vapor space cooling of tanks AY1O1, AY102, AZ1O1, AZ102 and supports the ability to exhaust air from each tank. Each system consists of a valved piping loop, a fan, condenser, and moisture separator; equipment is located inside each respective tank farm in its own hardened building. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.
Date: November 11, 1997
Creator: Clifton, F.T.
Partner: UNT Libraries Government Documents Department

Preoperational test report, primary ventilation system

Description: This represents a preoperational test report for Primary Ventilation Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system provides vapor space filtered venting of tanks AY101, AY102, AZ101, AZ102. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.
Date: November 4, 1997
Creator: Clifton, F.T.
Partner: UNT Libraries Government Documents Department

CW RFQ fabrication and engineering

Description: The design and fabrication of a four-vane RFQ to deliver a 100 mA CW proton beam at 6.7 MeV is described. This linac is an Oxygen-Free Electrolytic (OFE) copper structure 8 m in length and was fabricated using hydrogen furnace brazing as the joining technology.
Date: December 31, 1998
Creator: Schrage, D.; Young, L. & Roybal, P.
Partner: UNT Libraries Government Documents Department

Project W-320, 241-C-106 sluicing supporting documentation bibliography

Description: This supporting document has been prepared to make the listing of documentation used to develop, or in support of Project W-320, readily retrievable. All documents are sorted by document number and list the document type. Tank 241-C-106 has been included on the High Heat Load Watch List.
Date: August 6, 1998
Creator: Bailey, J.W.
Partner: UNT Libraries Government Documents Department

Heat Pipe Integrated Microsystems

Description: The trend in commercial electronics packaging to deliver ever smaller component packaging has enabled the development of new highly integrated modules meeting the demands of the next generation nano satellites. At under ten kilograms, these nano satellites will require both a greater density electronics and a melding of satellite structure and function. Better techniques must be developed to remove the subsequent heat generated by the active components required to-meet future computing requirements. Integration of commercially available electronics must be achieved without the increased costs normally associated with current generation multi chip modules. In this paper we present a method of component integration that uses silicon heat pipe technology and advanced flexible laminate circuit board technology to achieve thermal control and satellite structure. The' electronics/heat pipe stack then becomes an integral component of the spacecraft structure. Thermal management on satellites has always been a problem. The shrinking size of electronics and voltage requirements and the accompanying reduction in power dissipation has helped the situation somewhat. Nevertheless, the demands for increased onboard processing power have resulted in an ever increasing power density within the satellite body. With the introduction of nano satellites, small satellites under ten kilograms and under 1000 cubic inches, the area available on which to place hot components for proper heat dissipation has dwindled dramatically. The resulting satellite has become nearly a solid mass of electronics with nowhere to dissipate heat to space. The silicon heat pipe is attached to an aluminum frame using a thermally conductive epoxy or solder preform. The frame serves three purposes. First, the aluminum frame provides a heat conduction path from the edge of the heat pipe to radiators on the surface of the satellite. Secondly, it serves as an attachment point for extended structures attached to the satellite such as solar panels, radiators, ...
Date: March 30, 1999
Creator: Gass, K.; Robertson, P.J.; Shul, R. & Tigges, C.
Partner: UNT Libraries Government Documents Department

THERMAL DETECTION OF DNA AND PROTEINS DURING GEL ELECTROPHORESIS

Description: This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The goal of this project was to try to detect unstained, untagged, unlabeled DNA bands in real-time during gel electrophoresis using simple thermal measurements. The technical and ES&amp;H advantages to this approach could potentially be quite significant, especially given the extreme importance of gel electrophoresis to a wide variety of practical and research fields. The project was unable to demonstrate sufficient thermal sensitivity to detect DNA bands. It is clear that we still do not understand the gel electrophoresis phenomenon very well. The temperature control techniques developed during the course of this project have other useful applications.
Date: August 1, 2000
Creator: JOHNSTON, R.
Partner: UNT Libraries Government Documents Department

Automated cloning methods.

Description: Argonne has developed a series of automated protocols to generate bacterial expression clones by using a robotic system designed to be used in procedures associated with molecular biology. The system provides plate storage, temperature control from 4 to 37 C at various locations, and Biomek and Multimek pipetting stations. The automated system consists of a robot that transports sources from the active station on the automation system. Protocols for the automated generation of bacterial expression clones can be grouped into three categories (Figure 1). Fragment generation protocols are initiated on day one of the expression cloning procedure and encompass those protocols involved in generating purified coding region (PCR).
Date: August 22, 2001
Creator: Collart, F.
Partner: UNT Libraries Government Documents Department

Heavy Vehicle Propulsion Materials Program: Progress and Highlights

Description: The Heavy Vehicle Propulsion Materials Program was begun in 1997 to support the enabling materials needs of the DOE Office of Heavy Vehicle Technologies (OHVT). The technical agenda for the program grew out of the technology roadmap for the OHVT and includes efforts in materials for: fuel systems, exhaust aftertreatment, valve train, air handling, structural components, electrochemical propulsion, natural gas storage, and thermal management. A five-year program plan was written in early 2000, following a stakeholders workshop. The technical issues and planned and ongoing projects are discussed. Brief summaries of several technical highlights are given.
Date: June 19, 2000
Creator: Johnson, D. Ray & Diamond, Sidney
Partner: UNT Libraries Government Documents Department