1,608 Matching Results

Search Results

Advanced search parameters have been applied.

On the Theory of Thin and Thin-Walled Rods

Description: Through the work of V. Z. Vlasov a theory of thin-walled rods has been established that is widely applicable in practice. This theory was extended by A. A. Umanski to thin-walled rods of closed profile section. This report attempts to construct a theory of thin-walled rods, including the classical theory of deformation of thin rods, by making use of a kinematic assumption.
Date: October 1951
Creator: Dzhanelidze, G. Y.
Partner: UNT Libraries Government Documents Department

Fabrication of Uranium Wire

Description: From abstract: "The present report describes experimental work performed to establish a procedure for the production of uranium metal wire. In all cases, the size of the initial rod was 1/2 inch diameter. Three materials were used: hot extruded tuballoy rod, high purity cast tuballoy rod, and cast U-235 rod."
Date: October 25, 1949
Creator: Anderson, R. E.; Taub, J. M. & Doll, D. T.
Partner: UNT Libraries Government Documents Department

Measurement of distortion in second experimental control rod with temperature patterns simulating shim rod out and shim rod 50 percent inserted for Argonne Naval Reactor

Description: Thermal distortion tests were made on a stainless steel clad, cadmium-silver control rod furnished by the Argonne National Laboratory. Two temperature patterns supplied by the Argonne National Laboratory were simulated in these tests; one represented the shim-rod-out condition and the other the shim-rod-50-percent-inserted condition. The greatest reduction in clearance effected by thermal distortion was 0.076 inch. No permanent set of the control rod was observed after repeated heating and cooling cycles.
Date: September 26, 1951
Creator: Lietzke, A. F. & Nagey, T. F.
Partner: UNT Libraries Government Documents Department

Measurement of distortion in second experimental control rod for argonne naval reactor with constant transverse temperature gradient and uniform longitudinal temperature distribution

Description: Report presenting measurements of the thermal distortion of a stainless-steel clad, cadmium-silver reactor control rod. The temperature pattern of the rod is described. The maximum reduction in clearance obtained in the tests was 0.203 inch.
Date: September 26, 1951
Creator: Nagey, T. F. & Lietzke, A. F.
Partner: UNT Libraries Government Documents Department

Relief of Residual Stress in Streamline Tie Rods by Heat Treatment

Description: "About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees Fahrenheit" (p. 1).
Date: November 1941
Creator: Pollard, R. E. & Reinhart, Fred M.
Partner: UNT Libraries Government Documents Department

Vortex Noise From Rotating Cylindrical Rods

Description: "A series of round rods of the some diameter were rotated individually about the mid-point of each rod. Vortices are shed from the rods when in motion, giving rise to the emission of sound. With the rotating system placed in the open air, the distribution of sound in space, the acoustical power output, and the spectral distribution have been studied. The frequency of emission of vortices from any point on the rod is given by the formula of von Karman" (p. 1).
Date: February 1935
Creator: Stowell, E. Z. & Deming, A. F.
Partner: UNT Libraries Government Documents Department

Fabrication of Fuel Rods by Tandem Rolling

Description: From introduction: "The purpose of this report is to present the details of the exploratory and developmental work on tandem rolling, and the subsequent fabrication of tandem rolled fuel rods for irradiation testing in the Vallecitos Boiling Water Reactor."
Date: July 1961
Creator: Lingafelter, J. W.
Partner: UNT Libraries Government Documents Department

Solid-Phase-Reaction Studies of Control-Rod Materials

Description: Report discussing experiments on the interaction of neutron-absorber materials and metal matrix materials used in the fabrication of control rods, such as "boron, cadmium, and some of the rare-earth elements such as gadolinium and europium...In order to evaluate the reactions that might occur during fabrication and use, experiments were carried out in which combinations of the various control materials were heated in intimate contact with the several matrices at elevated temperatures."
Date: March 9, 1956
Creator: Gerds, Arnold F. & Mallett, Manley William
Partner: UNT Libraries Government Documents Department

Operating stresses in aircraft-engine crankshafts and connecting rods 2: instrumentation and test results

Description: Report presenting an investigation to develop methods and equipment for the measurement of operating stresses in aircraft-engine crankshafts and connecting rods. The results indicate that the measurement of stresses in connecting rods is feasible. Results regarding stresses in the crankshaft and stresses in the master connecting rod are provided.
Date: August 1945
Creator: Dutee, Francis J.; Phillips, Franklyn W. & Calvert, Howard F.
Partner: UNT Libraries Government Documents Department

Modern Methods of Protection Against Lightning

Description: "This bulletin will give those persons interested in protection against lightning concise, practical, and up-to-date information accompanied by specifications for installing the equipment so as to secure the greatest degree of protection with the type of installation chosen.... The several sample sets of specifications, given herein, calling for rods and fittings of differing cost, will enable the prospective buyer of lightning protection to make an intelligent choice." -- p. 2
Date: 1917
Creator: Covert, Roy N.
Partner: UNT Libraries Government Documents Department

Specification for Cleaning Zircaloy Fuel Rod Components

Description: Abstract: "This specification covers the cleaning of Zir caloy-2 components of PWR fuel rods and such tools, gauges, or other devices as may be required in subsequent handling, welding and inspection per Fuel Rod Specification AP-292545, Section II-A-4 and Section II-B-3."
Date: March 6, 1956
Creator: Fischer, R. L.
Partner: UNT Libraries Government Documents Department

Plastic Deformation in Grooved Rolls

Description: This report covers a study of the deformation characteristics of uranium in grooved rolls. The study's purpose was to provide a basis for possible improvements in the uniformity of the rolled rod produced for the Hanford and Savannah River reactors.
Date: September 27, 1955
Creator: Saller, Henry A.; Keeler, John R. & Cuddy, Lee J.
Partner: UNT Libraries Government Documents Department

The Effects of Chemical Impurities on the Quality of Rolled Uranium Rod

Description: Abstract: "Thirty-four uranium ingots containing controlled amounts of carbon, nitrogen, and Mgl2 slag were cast, rolled, and examined to investigate the relation between these impurities and the quality of the rolled rod. Carbon in concentrations up to 1400 ppm and nitrogen up to 170 ppm, either singly or in combination, had no significant effect on the number of defects observed in the rolled rod. The quality of the rods, however decreased with increasing amount of slag necessary to cause observable differences in the rod could not be detected on analysis, but was visible in the microstructure."
Date: October 1, 1954
Creator: Saller, Henry A.; Keeler, J. R. & Cuddy, L. J.
Partner: UNT Libraries Government Documents Department

The Effects of Chemical Impurities on the Quality of Rolled Uranium Rod

Description: Abstract: "The effects of nitrogen, slag, and hydrogen additions on the surface quality of rolled uranium rod were studied. The addition of 400 ppm of nitrogen resulted in severe striations. Slag inclusions elongated during rolling and produced short open seams in the etched surface. The effects of 9 to 10 ppm of hydrogen were obscured by defects in the original costings. These defects were caused by oxide films entrapped in the ingot."
Date: 1956
Creator: Saller, Henry A.; Keeler, John R. & Cuddy, Lee J.
Partner: UNT Libraries Government Documents Department

Further Studies on Control of the Converter Reactor

Description: Introduction: "This report is an extension of NAA-SR-Memo-178. The results show the number of control rods as a function of the amount of reactivity to be controlled. Numerical solutions are given for a typical example and are readily obtainable for other cases."
Date: May 12, 1952
Creator: Robinson, L. B.
Partner: UNT Libraries Government Documents Department

The Fabrication of Thorium Tubes

Description: Abstract: "Thorium tubes were cold drawn from extruded tube stock and also from drilled hot-rolled rod. Total reductions up to approximately 85 per cent were accomplished by conventional tube-drawing methods, without an intermediate anneal. The hard-drawn tubes had high tensile strength, but the ductility, as indicated by flaring and flattening tests, was low."
Date: January 16, 1953
Creator: Saller, Henry A. & Keeler, J. R.
Partner: UNT Libraries Government Documents Department

Experimental Fabrication of a Lightweight Control Rod

Description: Abstract: "The possibility of fabricating a lightweight control rod from one of several high cross-section materials was investigated. The major effort was directed toward the development of a titanium-clad rod containing a composite core of 25 weight per cent Gd2O3 in a matrix of titanium. Experimentation on both subscale and full-scale control-rod cores showed that the fabricating behavior of the two was not analogous. To roll the full-scale core successfully, it was necessary to lower the oxide content to 17 weight per cent. Subscale investigations were also carried out on titanium-cadmium, titanium-lanthanum, and titanium-gadolinium alloys."
Date: July 1, 1952
Creator: Saller, Henry A.; Stacy, J. T. & Keller, D. L.
Partner: UNT Libraries Government Documents Department

The Rolling of Thorium Rod

Description: Report discussing the rolling of thorium rods. Abstract: "Thorium rods, 1-7/16 inch in diameter, were rolled from Ames castings. The billets were roughed down in diamond-grooved rolls and finished in hand-rounding rolls. Remelted chips as well as primary-metal castings were rolled, and both yielded satisfactory rods. The surface quality of the rods was generally excellent, and the machined slugs were free of seams."
Date: December 19, 1951
Creator: Saller, Henry A.; Keeler, J. R. & Donley, R. J.
Partner: UNT Libraries Government Documents Department

New Beta Heat-Treating Salt Baths for Reducing Hydrogen Pickup by Uranium Rods

Description: The following report summarizes the results of the laboratory-scale work and pilot-plant scale work of a salt-batch composition that reduces the hydrogen pickup by uranium rods during the beta heat treatment, and the study of the influence of humidity over the salt bath on hydrogen pickup.
Date: June 18, 1957
Creator: Lortscher, L. L.; Sense, Karl A. & Filbert, Robert B.
Partner: UNT Libraries Government Documents Department

Crippling Strength of Axially Loaded Rods

Description: A new empirical formula was developed that holds good for any length and any material of a rod, and agrees well with the results of extensive strength tests. To facilitate calculations, three tables are included, giving the crippling load for solid and hollow sectioned wooden rods of different thickness and length, as well as for steel tubes manufactured according to the standards of Army Air Services Inspection. Further, a graphical method of calculation of the breaking load is derived in which a single curve is employed for determination of the allowable fiber stress.
Date: October 1921
Creator: Natalis, Fr. & Pawlowski, F. W.
Partner: UNT Libraries Government Documents Department

Theory of Thin-Walled Rods

Description: Starting with the Love equations for bending of extensible shells, "principal stress states" are sought for a thin-walled rod of arbitrary but open cross section. Principal stress states exclude those local states arising from end conditions which damp out with distance from the ends. It is found that for rods of intermediate length, long enough to avoid local bending at a support, and short enough that elementary torsion and bending are not the most significant stress states, four principal states exist.
Date: October 1951
Creator: Goldenveizer, A. L.
Partner: UNT Libraries Government Documents Department