456 Matching Results

Search Results

Advanced search parameters have been applied.

Simple PDP15 interface for the Versatec serial printer

Description: An interface was developed to go between the PDP 15/30 computer and the Versatec printer/plotter, model 200A, operating in the serial print mode. The interface construction involved fabricating a cable with two twisted pairs for a signal and a control line, speeding up the clock in the existing foreground teletype controller and changing less than a dozen wires in it. The associated I/ O device handler allows the printer to be used as the listing device in the Digital Equipment Corporation Advanced Monitor Software System. With the handler, the printer is capable of printing 80 character lines at approximately 120 lines per minute. (auth)
Date: January 1, 1974
Creator: Kosorok, J.R.
Partner: UNT Libraries Government Documents Department

Nuclear Energy Plant Optimization (NEPO) final report on aging and condition monitoring of low-voltage cable materials.

Description: This report summarizes results generated on a 5-year cable-aging program that constituted part of the Nuclear Energy Plant Optimization (NEPO) program, an effort cosponsored by the U. S. Department of Energy (DOE) and the Electric Power Research Institute (EPRI). The NEPO cable-aging effort concentrated on two important issues involving the development of better lifetime prediction methods as well as the development and testing of novel cable condition-monitoring (CM) techniques. To address improved life prediction methods, we first describe the use of time-temperature superposition principles, indicating how this approach improves the testing of the Arrhenius model by utilizing all of the experimentally generated data instead of a few selected and processed data points. Although reasonable superposition is often found, we show several cases where non-superposition is evident, a situation that violates the constant acceleration assumption normally used in accelerated aging studies. Long-term aging results over extended temperature ranges allow us to show that curvature in Arrhenius plots for elongation is a common occurrence. In all cases the curvature results in a lowering of the Arrhenius activation energy at lower temperatures implying that typical extrapolation of high temperature results over-estimates material lifetimes. The long-term results also allow us to test the significance of extrapolating through the crystalline melting point of semi-crystalline materials. By utilizing ultrasensitive oxygen consumption (UOC) measurements, we show that it is possible to probe the low temperature extrapolation region normally inaccessible to conventional accelerated aging studies. This allows the quantitative testing of the often-used Arrhenius extrapolation assumption. Such testing indicates that many materials again show evidence of ''downward'' curvature (E{sub a} values drop as the aging temperature is lowered) consistent with the limited elongation results and many literature results. It is also shown how the UOC approach allows the probing of temperatures that cross through the crystalline melting point ...
Date: November 1, 2005
Creator: Assink, Roger Alan; Gillen, Kenneth Todd & Bernstein, Robert
Partner: UNT Libraries Government Documents Department

Environment qualification of power cable for the hydrogen mitigation pump number 3

Description: This report presents the severe environment qualification of the power cable in severe radiation and thermal conditions. This qualification program provides Fluor Daniel Hanford Company information for the use of the new cable in the mixer pump for hydrogen mitigation and retrieval purposes.
Date: December 27, 1996
Creator: Benegas, T.R., Westinghouse Hanford
Partner: UNT Libraries Government Documents Department

Aging analyses of aircraft wire insulation

Description: Over the past two decades, Sandia has developed a variety of specialized analytical techniques for evaluating the long-term aging and stability of cable insulation and other related materials. These techniques have been applied to cable reliability studies involving numerous insulation types and environmental factors. This work has allowed the monitoring of the occurrence and progression of cable material deterioration in application environments, and has provided insights into material degradation mechanisms. It has also allowed development of more reliable lifetime prediction methodologies. As a part of the FAA program for intrusive inspection of aircraft wiring, they are beginning to apply a battery of techniques to assessing the condition of cable specimens removed from retired aircraft. It is anticipated that in a future part of this program, they may employ these techniques in conjunction with accelerated aging methodologies and models that the authros have developed and employed in the past to predict cable lifetimes. The types of materials to be assessed include 5 different wire types: polyimide, PVC/Glass/Nylon, extruded XL-polyalkene/PVDF, Poly-X, and XL-ETFE. This presentation provides a brief overview of the main techniques that will be employed in assessing the state of health of aircraft wire insulation. The discussion will be illustrated with data from their prior cable aging studies, highlighting the methods used and their important conclusions. A few of the techniques that they employ are widely used in aging studies on polymers, but others are unique to Sandia. All of their techniques are non-proprietary, and maybe of interest for use by others in terms of application to aircraft wiring analysis. At the end of this report is a list showing some leading references to papers that have been published in the open literature which provide more detailed information on the analytical techniques for elastomer aging studies. The first step in ...
Date: May 8, 2000
Partner: UNT Libraries Government Documents Department

Linac BPM cable phase matching

Description: This report explains the method chosen to phase match cables, it`s accuracy and the effects of mismatched cables on the position output of the Linac Beam Position Module.
Date: August 6, 1993
Creator: Arthur, J.
Partner: UNT Libraries Government Documents Department

Wire detecting apparatus and method

Description: This invention is comprised of an apparatus and method that combines a signal generator and a passive signal receiver to detect and record the path of partially or completely concealed electrical wiring without disturbing the concealing surface. The signal generator applies a series of electrical pulses to the selected wiring of interest. The applied pulses create a magnetic field about the wiring that can be detected by a coil contained within the signal receiver. An audible output connected to the receiver and driven by the coil reflects the receiver`s position with respect to the wiring. The receiver`s audible signal is strongest when the receiver is directly above the wiring and the long axis of the receiver`s coil is parallel to the wiring. A marking means is mounted on the receiver to mark the location of the wiring as the receiver is directed over the wiring`s concealing surface. Numerous marks made on various locations of the concealing surface will trace the path of the wiring of interest.
Date: December 31, 1991
Creator: Kronberg, J.W.
Partner: UNT Libraries Government Documents Department

Assembly and method for testing the integrity of stuffing tubes

Description: A stuffing tube integrity checking assembly includes first and second annular seals, with each seal adapted to be positioned about a stuffing tube penetration component. An annular inflation bladder is provided, the bladder having a slot extending longitudinally there along and including a separator for sealing the slot. A first valve is in fluid communication with the bladder for introducing pressurized fluid to the space defined by the bladder when mounted about the tube. First and second releasible clamps are provided. Each clamp assembly is positioned about the bladder for securing the bladder to one of the seals for thereby establishing a fluid-tight chamber about the tube.
Date: December 31, 1996
Creator: Morrison, E.F.
Partner: UNT Libraries Government Documents Department

Circuit bridging of digital equipment caused by smoke from a cable fire

Description: Advanced reactor systems are likely to use protection systems with digital electronics that ideally should be resistant to environmental hazards, including smoke from possible cable fires. Previous smoke tests have shown that digital safety systems can fail even at relatively low levels of smoke density and that short-term failures are likely to be caused by circuit bridging. Experiments were performed to examine these failures, with a focus on component packaging and protection schemes. Circuit bridging, which causes increased leakage currents and arcs, was gauged by measuring leakage currents among the leads of component packages. The resistance among circuit leads typically varies over a wide range, depending on the nature of the circuitry between the pins, bias conditions, circuit board material, etc. Resistance between leads can be as low as 20 k{Omega} and still be good, depending on the component. For these tests, the authors chose a printed circuit board and components that normally have an interlead resistance above 10{sup 12} {Omega}, but if the circuit is exposed to smoke, circuit bridging causes the resistance to fall below 10{sup 3} {Omega}. Plated-through-hole (PTH) and surface-mounted (SMT) packages were exposed to a series of different smoke environments using a mixture of environmentally qualified cables for fuel. Conformal coatings and enclosures were tested as circuit protection methods. High fuel levels, high humidity, and high flaming burns were the conditions most likely to cause circuit bridging. The inexpensive conformal coating that was tested - an acrylic spray - reduced leakage currents, but enclosure in a chassis with a fan did not. PTH packages were more resistant to smoke-induced circuit bridging than SMT packages. Active components failed most often in tests where the leakage currents were high, but failure did not always accompany high leakage currents.
Date: March 1, 1997
Creator: Tanaka, T.J. & Anderson, D.J.
Partner: UNT Libraries Government Documents Department

Photovoltaic power systems and the National Electrical Code: Suggested practices

Description: This guide provides information on how the National Electrical Code (NEC) applies to photovoltaic systems. The guide is not intended to supplant or replace the NEC; it paraphrases the NEC where it pertains to photovoltaic systems and should be used with the full text of the NEC. Users of this guide should be thoroughly familiar with the NEC and know the engineering principles and hazards associated with electrical and photovoltaic power systems. The information in this guide is the best available at the time of publication and is believed to be technically accurate; it will be updated frequently. Application of this information and results obtained are the responsibility of the user.
Date: December 1, 1996
Creator: Wiles, J.
Partner: UNT Libraries Government Documents Department

Shock mitigation for the PFLs at the SATURN accelerator

Description: Accelerometer measurements were made on the SATURN pulse forming lines (PFL) to determine the mechanism responsible for severe metal deformation around the water switch openings and cracking of welded seams. A reason for this problem and a solution were established. A simple shock mitigating pad under the support stand for the PFL provides more than adequate protection from shock damage and will greatly extend the useful life of the power flow sections of SATURN.
Date: June 1, 1997
Creator: Craven, R.E.
Partner: UNT Libraries Government Documents Department

Preliminary design note for a direct coupled 200,000 amp neutrino horn power supply with energy recovery

Description: The availability of high current, (several thousand amperes) silicon controlled rectifiers and high current, low loss capacitors make it practical to design a direct coupled energy discharge power supply for the neutrino horns in the proposed NuMI facility at Fermilab. The neutrino horns require a continuous pulse train of 200,000 A and 1 msec duration at a pulse period of 1.5 seconds. This high current pulse train yields a system load current of about 9,000 A rms. Using a high power coupling transformer between the energy stored in a capacitor bank and the horns is very expensive because the transformer secondary winding would have to be rated for 9,000 A rms at about 1,400 Vpk. The transformer would also add leakage inductance to the discharge circuit, take up a substantial amount of floor space and make stored energy recovery from the horns less effective or maybe even impractical. The transformer would need a reset winding to remove the high remnant magnet field in the transformer steel which is caused by the unipolar discharge pulses. A coupling transformer is practical for high voltage loads, but the horns operate at a relatively low voltage of about 1,400 V, which makes direct coupling very attractive. This note describes a preliminary design for a direct coupled system. From the design notes the authors can conclude that direct coupling is economical, practical, relatively simple, can use energy recovery and does not require materials or equipment that is hard to obtain. The charging power supply could be two standard (Fermilab) 240 kW beamline power supplies connected in series and grounded at the midpoint. The capacitor bank, switches, transmission line and controls can be most economically assembled in house. They may conclude that it is desirable to build a direct coupled neutrino horn power supply system and ...
Date: March 1, 1995
Creator: Visser, A.T.
Partner: UNT Libraries Government Documents Department

Haines - Scagway Submarine Cable Intertie Project, Haines to Scagway, Alaska Final Technical and Construction Report

Description: The Haines to Skagway submarine cable project is located n Taiya Inlet, at the north end of Lynn Canal, in Southeast Alaska. The cable is approximately 15 miles long, with three landings and splice vaults. The cable is 35 kV, 3-Phase, and armored. The cable interconnects the Goat Lake Hydro Project near Skagway with the community of Haines. Both communities are now on 100% hydroelectric power. The Haines to Skagway submarine cable is the result of AP&T's goal of an alternative, economic, and environmentally friendly energy source for the communities served and to eliminate the use of diesel fuel as the primary source of energy. Diesel units will continue to be used as a backup system.
Date: November 1, 1998
Creator: See, Alan; Rinehart, Bennie N. & Marin, Glen
Partner: UNT Libraries Government Documents Department

An Evaluation of Condition Monitoring Techniques for Low-Voltage Electric Cables

Description: Aging of systems and components in nuclear power plants is a well known occurrence that must be managed to ensure the continued safe operation of these plants. Much of the degradation due to aging is controlled through periodic maintenance and/or component replacement. However, there are components that do not receive periodic maintenance or monitoring once they are installed; electric cables are such a component. To provide a means of monitoring the condition of electric cables, research is ongoing to evaluate promising condition monitoring (CM) techniques that can be used in situ to monitor cable condition and predict remaining life. While several techniques are promising, each has limitations that must be considered in its application. This paper discusses the theory behind several of the promising cable CM techniques being studied, along with their effectiveness for monitoring aging degradation in typical cable insulation materials, such as cross-linked polyethylene and ethylene propylene rubber. Successes and limitations of each technique are also presented.
Date: July 23, 2000
Creator: Lofaro, Robert J.; Grove, Edward & Soo, Peter
Partner: UNT Libraries Government Documents Department

Design of the Atlas 240 kV Marx modules

Description: A prototype 240 kV, oil-insulated Marx module has been designed and constructed at the Los Alamos National Laboratory (LANL). The prototype will be used for testing and certifying the design of the Marx module and certain components, including the closing switches, series resistor, and the capacitors themselves. The prototype will also be used to evaluate proposed mechanical systems designs. Information gained from the construction and testing of the 4-capacitor prototype will be folded into the design of the 16-capacitor maintenance unit. The prototype module consists of four 60 kV capacitors, two closing switches, one shunt resistor, and one series resistor. Cables are used to deliver the current to a dummy load scaled to match Atlas system parameters. The Marx unit is contained in a structure made from G-10, suspended from a steel frame that also serves to support components of the trigger, charging, and control system. Appropriate safety and charging systems are an integral part of the prototype design.
Date: June 1, 1997
Creator: Bowman, D.W.; Bennett, G. & Biehl, F.
Partner: UNT Libraries Government Documents Department

Literature review of environmental qualification of safety-related electric cables: Literature analysis and appendices. Volume 2

Description: In support of the US NRC Environmental Qualification (EQ) Research Program, a literature review was performed to identify past relevant work that could be used to help fully or partially resolve issues of interest related to the qualification of low-voltage electric cable. A summary of the literature reviewed is documented in Volume 1 of this report. In this, Volume 2 of the report, dossiers are presented which document the issues selected for investigation in this program, along with recommendations for future work to resolve the issues, when necessary. The dossiers are based on an analysis of the literature reviewed, as well as expert opinions. This analysis includes a critical review of the information available from past and ongoing work in thirteen specific areas related to EQ. The analysis for each area focuses on one or more questions which must be answered to consider a particular issue resolved. Results of the analysis are presented, along with recommendations for future work. The analysis is documented in the form of a dossier for each of the areas analyzed.
Date: April 1996
Creator: Lofaro, R.; Bowerman, B. & Carbonaro, J.
Partner: UNT Libraries Government Documents Department