645 Matching Results

Search Results

Advanced search parameters have been applied.

Evaluation of Heat Dissipation in the BPM Buttons

Description: Growth of circulating current in the storage rings drastically increases heating of the beam position monitor (BPM) buttons due to the induced trapped modes is drastically increasing. Excessive heating can lead to the errors in the measuring of beam position or even catastrophic failures of the pick-up assembly. In this paper we present calculations of heat generated in the button for different geometries and materials. The obtained results are used for the optimization of the NSLS-II BPM buttons design.
Date: May 4, 2009
Creator: Pinayev,I. & Blednyhk, A.
Partner: UNT Libraries Government Documents Department

A General Analysis of Thin Wire Pickups for High Frequency Beam Position Monitors

Description: In many particle accelerators, a large number of high frequency beam position monitors (BPMs) are required to track and correct the orbit of the beam. Therefore, simple, sensitive, low cost pickup designs for such BPMs are of widespread interest. In this paper, a general analysis of arbitrarily terminated thin wire stripline or
Date: October 1, 1990
Creator: Barry, Walter
Partner: UNT Libraries Government Documents Department

Optimisation of NSLS-II Blade X-ray Beam Position Monitors: from Photoemission type to Diamond Detector

Description: Optimisation of blade type x-ray beam position monitors (XBPM) was performed for NSLS-II undulator IVU20. Blade material, con and #64257;guration and operation principle was analysed in order to improve XBPM performance. Optimisation is based on calculation of the XBPM signal spatial distribution. Along with standard photoemission type XBPM a Diamond Detector Blades (DDB) were analysed as blades for XBPMs. DDB XBPMs can help to overcome drawbacks of the photoemission blade XBPMs.
Date: July 10, 2012
Creator: P., ILINSKI
Partner: UNT Libraries Government Documents Department

Comparison of RF BPM Receivers for NSLS-II Project

Description: The NSLS-II Light Source being built at Brookhaven National Laboratory requires submicron stability of the electron orbit in the storage ring in order to utilize fully very small emittances and electron beam sizes. This sets high stability requirements for beam position monitors and a program has been initiated for the purpose of characterizing RF beam position monitor (BPM) receivers in use at other light sources. Present state-of-the-art performance will be contrasted with more recently available technologies.
Date: May 4, 2009
Creator: Pinayev,I. & Singh, O.
Partner: UNT Libraries Government Documents Department

Phase and synchronous detector theory as applied to beam position and intensity measurements

Description: A popular signal processing technique for beam position measurements uses the principle of amplitude-to-phase (AM/PM) conversion and phase detection. This technique processes position-sensitive beam-image-current probe-signals into output signals that are proportional to the beam`s position. These same probe signals may be summed and processed in a different fashion to provide output signals that are proportional to the peak beam current which is typically referred to as beam intensity. This paper derives the transfer functions for the AM/PM beam position and peak beam current processors.
Date: May 1, 1995
Creator: Gilpatrick, J.D.
Partner: UNT Libraries Government Documents Department

Observation of the spread of the readings in the Linac toroids and BPMs

Description: The readback accuracy on the high-energy toroids is about 0.26 mA. This does not consider, completely, the relative offsets among the toroids, just the accuracy of one reading on one toroid. Similarly, if you remove the way in which the beam moves in the beam pipe and ignore the relative offsets of the BPMs themselves, then the absolute accuracy of the reading on a BPM is 35 microns.
Date: November 9, 2001
Creator: McCrory, Elliott S
Partner: UNT Libraries Government Documents Department

Measured longitudinal beam impedance of a Tevatron separator

Description: Twenty two separators are currently installed in the Tevatron. The longitudinal impedance of one of these devices was recently measured with a stretched wire. The stretched wire technique can only measure impedance below the cutoff frequency (500MHz). The geometry of a separator is similar to an un-terminated stripline beam position detector. The separator plates occupy a 13.5'' ID vacuum tank, are 101'' long, 7.8'' wide, and have a 2'' gap between them. The differential characteristic impedance between the plates is estimated to be 81 {Gamma} and the common mode impedance plate to ground is about 42 {Gamma}.
Date: December 9, 2002
Creator: Crisp, James L & Fellenz, Brian J
Partner: UNT Libraries Government Documents Department

Measurements of Beam Momentum at the Stacking Energy of the Accumulator

Description: The momentum and orbit length of beam on the central and extraction orbits of the Antiproton Source Accumulator are calculated from measurements of revolution frequency and transverse beam position. This report gives the results of measurements made at the stacking energy before and after the 1998-99 Accumulator lattice upgrade. Before the lattice upgrade, the Accumulator central orbit length and momentum are measured to be: L{sub c} = 474.0433 {+-} 0.0025 m, p{sub c} = 8819.5 {+-} 4.1 MeV/c. After the lattice upgrade the central orbit length and momentum are measured to be: L{sub c} = 474.0532 {+-} 0.0016 m, p{sub c} = 8803.4 {+-} 2.7 MeV/c. The extraction orbit length and momentum prior to the lattice upgrade are measured to be: L{sub e} = 474.1916 {+-} 0.0054 m, p{sub e} = 8900.8 {+-} 9.2 MeV/c. After the lattice upgrade the extraction orbit length and momentum are measured to be: L{sub e} = 474.1599 {+-} 0.0036 m, p{sub e} = 8886.3 {+-} 6.1 MeV/c.
Date: November 29, 2000
Creator: Werkema, Steve
Partner: UNT Libraries Government Documents Department

RHIC BPM Performance: Comparison of Run 2003 and 2004.

Description: Identification of malfunctioning beam position monitors (BPMs) play an important role in any orbit or turn-by-turn analysis. Singular value decomposition (SVD) and Fourier transform methods were recently employed to identify malfunctioning BPMs at RHIC. A detailed statistical comparison between the two methods for Run 2003 was in good agreement and proved to be a robust method to identify faulty BPMs. We evaluate detailed BPM performance for different upgrades of BPM low-level software during Run 2003 and 2004.
Date: July 5, 2004
Creator: Calaga, R.
Partner: UNT Libraries Government Documents Department

Transverse Coupling Measurement Using SVD Modes From Beam Histories.

Description: In this report we investigate the measurement of local transverse coupling from turn-by-turn data measured at a large number of beam position monitors. We focus on a direct measurement of coupled lattice functions using the singular value decomposition (SVD) modes and explore the accuracy of this method.
Date: July 5, 2004
Creator: Calaga, R. & Wang, C.
Partner: UNT Libraries Government Documents Department

RF systems for the betatron-node scheme experiment at LBNL

Description: Two-beam accelerators based upon relativistic klystrons (RK's) have been proposed as power sources for future generation electron-positron linear colliders. These drivers are known to suffer from several transverse beam-breakup (BBU) instabilities. A program to study a particular technique (the 'betatron node scheme') of ameliorating the high frequency BBU is under way at LBL. Central to this study are the pillbox RF cavities and RF beam position monitors (BPM's) employed. This paper discusses the design, fabrication, and testing of the RF components. Details of the signal processing and analysis will be presented.
Date: June 22, 2001
Creator: Lidia, Steven M.; De Santis, Stefano & Houck, Timothy
Partner: UNT Libraries Government Documents Department

Optical sensors for accelerator diagnostics. Final report for the period September 15, 1998 - September 14, 2001

Description: DARHT utilizes a long pulse electron beam having a duration in excess of 2 microseconds. An electro-optic voltage sensor technology has been developed and commissioned to address this unique diagnostic environment. Over 200 sensors have demonstrated 0.25% accuracy. Deployment is expected in 2002.
Date: April 8, 2002
Creator: Yakymyshyn, Christopher P.
Partner: UNT Libraries Government Documents Department

3-D electromagnetic modeling of wakefields in accelerator components

Description: We discuss the use of 3-D finite-difference time-domain (FDTD) electromagnetic codes for modeling accelerator components. Computational modeling of cylindrically symmetric structures such as induction accelerator cells has been very successful in predicting the wake potential and wake impedances of these structures, but full 3-D modeling of complex structures has been limited due to substantial computer resources required for a full 3-D model. New massively parallel 3-D time domain electromagnetic codes now under development using conforming unstructured meshes allow a substantial increase in the geometric fidelity of the structures being modeled. Development of these new codes are discussed in context of applicability to accelerator problems. Various 3-D structures are tested with an existing cubical cell FDTD code and wake impedances compared with simple analytic models for the structures; results will be used as benchmarks for testing the new time time domain codes. Structures under consideration include a stripline beam position monitor as well as circular and elliptical apertures in circular waveguides. Excellent agreement for monopole and dipole impedances with models were found for these structures below the cutoff frequency of the beam line.
Date: September 18, 1996
Creator: Poole, B.R.; Caporaso, G.J.; Ng, Wang C.; Shang, C.C. & Steich, D.
Partner: UNT Libraries Government Documents Department


Description: The RHIC vertical ac dipole was installed in the summer of 2001. The magnet is located in the interaction region between sector 3 and sector 4 common to both beams. The resonant frequency of the ac dipole was first configured to be around half of the beam revolution frequency to act as a spin flipper. At the end of the RHIC 2002 run, the ac dipole frequency was reconfigured for linear optics studies. A 0.35 mm driven betatron oscillation was excited with the vertical ac dipole and the vertical betatron functions and phase advances at each beam position monitor (BPM) around the RHIC yellow ring were measured using the excited coherence. We also recorded horizontal turn-by-turn beam positions at each BPM location to investigate coupling effects. Analysis algorithms and measurement results are presented.
Date: June 2, 2002
Partner: UNT Libraries Government Documents Department

A photon beam position monitor for SSRL beamline 9

Description: We present here the concept of a simple one dimensional photon beam position monitor for use with high power synchrotron radiation beams. It has micron resolution, reasonable linearity in an inexpensive design. Most important, is its insensitivity to diffusely scattered low energy radiation from components upstream of the monitor.
Date: October 1, 1995
Creator: Cerino, J.A.; Rabedeau, T. & Bowen, W.
Partner: UNT Libraries Government Documents Department

Quadrupole shunt experiments at SPEAR

Description: As part of a program to align and stabilize the SPEAR storage ring, a switchable shunt resistor was installed on each quadrupole to bypass a small percentage of the magnet current. The impact of a quadrupole shunt is to move the electron beam orbit in proportion to the off-axis beam position at the quadrupole, and to shift the betatron tune. Initially, quadrupole shunts in SPEAR were used to position the electron beam in the center of the quadrupoles. This provided readback offsets for nearby beam position monitors, and helped to steer the photon beams with low-amplitude corrector currents. The shunt-induced tune shift measurements were then processed in MAD to derive a lattice model.
Date: May 1, 1996
Creator: Corbett, W.J.; Hettel, R.O. & Nuhn, H.-D.
Partner: UNT Libraries Government Documents Department

Performance of the upgraded NSLS beam position monitors

Description: The design and initial performance of the original NSLS beam position monitor were described by J. Bittner and R. Biscardi in 1989. The receiver, which processes signals from four button type pick-up electrodes by time-division multiplexing, operates at the third harmonic of the ring rf frequency (158.66 MHz). It has an output bandwidth of about 2 kHz and a dynamic signal range of approximately 36 dB. A total of 92 receivers have been installed in the NSLS X-ray and VUV storage rings for orbit monitoring and for real time feedback. As part of a continuous effort to improve the NSLS storage ring performance, the BPMs as well as other instrumentation systems have also been undergoing upgrades over the past two years to improve their performance. In the BPM, the front end has been modified to prevent saturation of the rf multiplexing switch, the detector operating point was changed to improve output signal linearity, the dynamic range was increased to over 60 dB, and the gain calibration was standardized to 0.5 volts/mm (i.e. 2 {micro}m/mV). This paper describes the BPM modifications and presents some performance data and measurements on stored beam.
Date: July 1, 1997
Creator: Nawrocky, R.J. & Keane, J.
Partner: UNT Libraries Government Documents Department

Studies of beam induced dipole-mode signals in accelerating structures at the SLC

Description: Beam emittance dilution by self induced transverse fields (wakefields) in accelerating structures is a key problem in linear accelerators. To minimize the wakefield effects the beam trajectory must be precisely centered within the structures. An efficient way to achieve this is to detect beam induced microwave signals in the lowest dipole mode band and to steer the beam by minimizing these signals. This paper briefly covers some experiences from SLC S-band structures, but mainly concentrates on results of a wakefield instrumentation scheme applied to a NLC prototype X-band structure and tested with beam in the SLC linac. A beam based in-situ structure straightness measurement is shown as well as results of beam steering experiments based on phase and amplitude detection of two separated modes in the structure. After centering the beam the reduction of the wakefield was demonstrated independently by probing it with a test bunch that is deflected by the residual wakefield at a short distance behind the drive bunch.
Date: June 1, 1997
Creator: Seidel, M.
Partner: UNT Libraries Government Documents Department

1 nA beam position monitoring system

Description: A system has been developed at Jefferson Lab for measuring transverse position of very low current beams delivered to the Experimental Hall B of the Continuous Electron Beam Accelerator Facility (CEBAF). At the heart of the system is a position sensitive cavity operating at 1497 MHz. The cavity utilizes a unique design which achieves a high sensitivity to beam position at a relatively low cavity Q. The cavity output RF signal is processed using a down-converter and a commercial lock-in amplifier operating at 100 kHz. The system interfaces with a VME based EPICS control system using the IEEE, 488 bus. The main features of the system are simple and robust design, and wide dynamic range capable of handling beam currents from 1 nA to 1000 nA with an expected resolution better than 100 {mu}m. This paper outlines the design of the system.
Date: June 1, 1997
Creator: Ursic, R.; Flood, R. & Piller, C.
Partner: UNT Libraries Government Documents Department

The Algebraic Reconstruction Technique (ART)

Description: Projections of charged particle beam current density (profiles) are frequently used as a measure of beam position and size. In conventional practice only two projections, usually horizontal and vertical, are measured. This puts a severe limit on the detail of information that can be achieved. A third projection provides a significant improvement. The Algebraic Reconstruction Technique (ART) uses three or more projections to reconstruct 3-dimensional density profiles. At the 200 MeV H-linac, we have used this technique to measure beam density, and it has proved very helpful, especially in helping determine if there is any coupling present in x-y phase space. We will present examples of measurements of current densities using this technique.
Date: July 1, 1997
Creator: Raparia, D.; Alessi, J. & Kponou, A.
Partner: UNT Libraries Government Documents Department