UNT Libraries Government Documents Department - 5,164 Matching Results

Search Results

Additional free-flight tests of the rolling effectiveness of several wing-spoiler arrangements at high subsonic, transonic, and supersonic speeds

Description: From Introduction: "The purpose of the present paper is to present results obtained recently relating to the characteristics of a full-span sharp-edge spoiler with an 0.02-chord projection above the wing surface at several chordwise positions and also to the relative effectiveness of the sharp-edge spoiler and a wedge-type spoiler located at the 80-percent-chord line."
Date: November 24, 1948
Creator: Strass, H Kurt

Additional measurements of the low-speed static stability of a configuration employing three triangular wing panels and a body of equal length

Description: From Introduction: "The results of an investigation of the low-speed static stability of a simplified model of such an arrangement having one of the airfoils placed vertically on top of the body and the other two as wing panels having negative dihedral are presented in reference 1. In order to provide information for predicting the effects of changes in the basic configuration on the low-speed stability characteristics presented in reference 1, additional measurements have been made."
Date: July 25, 1955
Creator: Delany, Noel K

Additional results of an investigation at transonic speeds to determine the effects of a heated propulsive jet on the drag characteristics of a series of related afterbodies

Description: From Introduction: "Presented in this report are the basic data obtained from investigation. The data are presented with limited analysis in order to expedite their availability to those concerned with jet-exit-afterbody design."
Date: September 24, 1956
Creator: Henry, Beverly Z JR & Cahn, Maurice S

Additional Results on the Static Longitudinal and Lateral Stability Characteristics of a 0.05-Scale Model of the Convair F2Y-1 Airplane at High Subsonic Speeds

Description: Additional results on the static longitudinal and lateral stability characteristics of a 0.05-scale model of the Convair F2Y-1 water-based fighter airplane were obtained in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.92. The maximum angle-of-attack range (obtained at the lower Mach numbers) was from -2 degrees to 25 degrees. The sideslip-angle range investigated was from -4 degrees to 12 degrees. The investigation included effects of various arrangements of wing fences, leading-edge chord-extensions, and leading-edge notches. Various fuselage fences, spoilers, and a dive brake also were investigated. From overall considerations of lift, drag, and pitching moments, it appears that there were two modifications somewhat superior to any of the others investigated: One was a configuration that employed a full-chord fence and a partial-chord fence located at 0.63 semispan and 0.55 semispan, respectively. The second was a leading-edge chord-extension that extended from 0.68 semispan to 0.85 semispan in combination with a leading-edge notch located at 0.68 semispan. With plus or minus 10 degrees aileron, the estimated wing-tip helix angle was reduced from 0.125 at a Mach number of 0.50 to 0.088 at a Mach number of 0.92, with corresponding rates of roll of 4.0 and 5.2 radians per second. The upper aft fuselage dive brake, when deflected 30 degrees and 60 degrees, reduced the rudder effectiveness about 10 to 20 percent and about 35 to 50 percent, respectively.
Date: August 10, 1954
Creator: Spreeman, Kenneth P. & Few, Albert G.

Adhesive and protective characteristics of ceramic coating A-417 and its effect on engine life of forged Refractaloy-26 (AMS 5760) and cast stellite 21 (AMS 5385) turbine blades

Description: The adhesive and protective characteristics of National Bureau of Standards Coating A-417 were investigated, as well as the effect of the coating on the life of forged Refractaloy 26 and cast Stellite 21 turbine blades. Coated and uncoated blades were run in a full-scale J33-9 engine and were subjected to simulated service operations consisting of consecutive 20-minute cycles (15 min at rated speed and approximately 5 min at idle). The ceramic coating adhered well to Refractaloy 26 and Stellite 21 turbine blades operated at 1500 degrees F. The coating also prevented corrosion of the Refractaloy 26, a corrosion-sensitive nickel-base alloy, and of the Stellite 21, a relatively corrosion-resistant cobalt-base alloy. Although the coating prevented corrosion of both alloys, it had no apparent effect on blade life.
Date: February 12, 1953
Creator: Garrett, Floyd B & Gyorgak, Charles A

Aerodynamic and hydrodynamic characteristics of a deck-inlet multijet water-based-aircraft configuration designed for supersonic flight

Description: From Introduction: "In the present investigation, lift, drag, and pitching moment were determined over a Mach number range 0.6 to 1.42. Smooth-water takeoff and landing stability and resistance were investigated. A brief check of the rough-water spray and behavior was also made."
Date: December 5, 1956
Creator: Bielat, Ralph P; Coffee, Claude W , Jr & Petynia, William W

Aerodynamic and hydrodynamic characteristics of a proposed supersonic multijet water-based hydro-ski aircraft with a variable-incidence wing

Description: From Introduction: "The configuration described in this paper represents one approach to such an airplane and the results of the wind-tunnel and tank evaluations are presented. In the present investigation, the aerodynamic longitudinal characteristics over a Mach number range from 0.6 to 1.97 were obtained."
Date: October 23, 1957
Creator: Petynia, William W.; Hasson, Dennis F. & Spooner, Stanley H.

Aerodynamic and hydrodynamic characteristics of models of some aircraft-towed mine-sweeping devices : TED No. NACA AR 8201

Description: From Introduction: "A study is being conducted by the U.S. Naval Air Development Center to determine the feasibility of several airborne magnetic mine-sweeping methods. The advantages of a satisfactory airborne method are greater safety and speed than are possible with existing surface methods. The three configurations investigated are described in some detail in reference 1 where they are designated as the double Q-sweep, the modified double-catenary sweep and the M-sweep."
Date: December 1, 1955
Creator: Shanks, Robert E

Aerodynamic characteristics and pressure distributions of a 6-percent-thick 49 degree sweptback wing with blowing over half-span and full-span flaps

Description: From Introduction: "The investigation reported herein was initiated to define further the effects on the aerodynamic characteristics and load distribution of a thin, sweptback wing of a low-pressure blowing system and also to provide information on which to base a more thorough study of a complete airplane configuration."
Date: September 20, 1955
Creator: Whittle, Edward F , Jr & Mclemore, H Clyde

Aerodynamic characteristics at high and low subsonic Mach numbers of four NACA 6-series airfoil sections at angles of attack from -2 to 31 degrees

Description: From Introduction: "The airfoil sections tested, which differ only in thickness ratio, were the NACA 64-006, 64-008, 64-010, and 641-012. Lift, drag, and pitching-moment data were obtained for Mach numbers of 0.3 to that for tunnel choke at angles of attack of -2^o to 31^o. The results of this investigation are reported herein."
Date: June 5, 1953
Creator: Wilson, Homer B., Jr. & Horton, Elmer A.

Aerodynamic Characteristics at High and Low Subsonic Mach Numbers of the NACA 0012, 64(sub 2)-015, and 64(sub 3)-018 Airfoil Sections at Angles of Attack from -2 Degrees to 30 Degrees

Description: An investigation has been made in the Langley low-turbulence pressure tunnel of the aerodynamic characteristics of the NACA 0012, 64(sub 2)-015, and 64(sub 3)-018 airfoil sections. Data were obtained at Mach numbers from 0.3 to that for tunnel choke, at angles of attack from -2deg to 30deg, and with the surface. of each airfoil smooth-and with roughness applied at the leading edge.The Reynolds numbers of the tests ranged from 0.8 x 10(exp 6) to 4.4 x 10(exp 6). The results are presented as variations of lift, drag, and quarter-chord pitching-moment coefficients with Mach number.
Date: 1954?
Creator: Critzos, Chris C.

Aerodynamic characteristics at high speeds of a two-blade NACA 10-(3)(062)-045 propeller and of a two-blade NACA 10-(3)(08)-045 propeller

Description: From Introduction: "The aerodynamic characteristics of a series of 10-foot-diameter propellers are being investigated in the Langley 16-foot high-speed tunnel in a comprehensive propeller research program. Using high-critical-speed NACA 16-series airfoil sections (reference 1), these propellers are designed to have Betz minimum induced-energy loss loading (reference 2) for a blade angle of 45^o at the 0.7 radius, when used as a four-blade propeller operating at an advance ratio of approximately 2.1 The ultimate purpose of the program is to determine the influence upon propeller design factors and of compressiblity; the propeller tests reported herein form part of the investigation of the effects of blade-section thickness ratio."
Date: October 1, 1948
Creator: Solomon, William