UNT Libraries Government Documents Department - 1,263 Matching Results

Search Results

Aerodynamic characteristics and flap loads of the brake-flap installation on the 0.40-scale model of the F4F-3 left wing panel

Description: From Introduction: "The data are presented in coefficient form and include lift, drag, and pitching-moment coefficients of the airfoil-flap comoinations and the normal-force, chord-force, and hinge-moment coefficients of the upper (perforated split) flap and lower (slotted) flap."
Date: October 1942
Creator: Liddell, Robert B

Aerodynamic characteristics of a 4-engine monoplane showing comparison of air-cooled and liquid-cooled engine installations

Description: From Introduction: "An investigation has been conducted in the N.A.C.A. full-scale wind tunnel to determine the aerodynamic characteristics of a 1/4-scale model of a 4-engine monoplane when equipped with comparable air-cooled engine and liquid-cooled engine installations. The air-cooled engine installation consisted of nacelles equipped with N..A.C.A. cowlings and oil coolers located in the leading edge of the wing."
Date: July 1939
Creator: Wilson, Herbert A , Jr & Silverstein, Abe

Aerodynamic characteristics of a slot-lip aileron and slotted flap for dive brakes

Description: From Introduction: "As a part of this investigation, a study is being made of test results obtained during the development of devices designed primarily for other purposes, such as high lift or lateral control, but which may also be used for dive control. These results have been reanalyzed and are herein presented in a form that should make them convenient for design purposes."
Date: April 1941
Creator: Rogallo, F M

Aerodynamic characteristics of four NACA airfoil sections designed for helicopter rotor blades

Description: From Introduction: "The purpose of the present work is to extend the previous investigation and to derive additional airfoil sections designed to minimize the undesirable characteristics of the previously tested airfoils. The tests of these additional airfoils were made in the Langley two-dimensional low-turbulence tunnel (LTT)."
Date: February 1946
Creator: Rice, Fred J , Jr

Aerodynamic characteristics of several modifications of a 0.45-scale model of the vertical tail of the Curtiss XP-62 airplane

Description: From Introduction: "In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane."
Date: July 1946
Creator: Liddell, Robert B.

Aerodynamics of the carburetor air scoop and the engine cowling of a single-engine torpedo-bomber-type airplane

Description: From Introduction: "An investigation of the power-plant installation of a single-engine torpedo-bomber-type airplane has been conducted in the NACA Cleveland altitude wind tunnel at the request of the Bureau of Aeronautics, Navy Department. A similar investigation was previously conducted on a three-tenths scale mock-up of the forward portion of the fuselage of this airplane in the Langley 20-foot tunnel. (See reference 1)."
Date: June 1946
Creator: Palter, Herman

Air-consumption parameters for automatic mixture control of aircraft engines

Description: From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."
Date: September 1944
Creator: Shames, Sidney J

Airfoil-contour modifications based on (epsilon)-curve method of calculating pressure distribution

Description: From Introduction: "Certain alternations of a qualitative nature may be performed in spite of the fact that a pressure change cannot be prescribed. It is the purpose of this paper to indicate a method by which qualitative alternation may be performed. It will be noted that the present method of contour modification will serve the intended purpose of the inverse method."
Date: July 1, 1944
Creator: Theodorsen, Theodore