UNT Libraries Government Documents Department - 1,296 Matching Results

Search Results

100-K water plant facilities data for G.E. scoping

Description: This report discusses seven items related to the design of the 100-K water plant facilities. These items include: the number of process water connections to the reactor building, valving at the control building, and number of main pumping units; effect on heating system of the Hanford power outage during the winter period; reactor supply conditions; power requirements and steam flow at the local power plant; the service water system; general arrangement of the heat exchanger building; and pumping station control.
Date: August 8, 1952
Creator: Patterson, R.K.

234-5 Building RM line equipment tests, Task III mixer

Description: Several operations that are important to the process as carried out in Task III (Reduction) are performed by the mixer. In order to specify the process certain tests were made to study these operations and are discussed in this report. They include: Mixing Time, Mixer Discharge Rate, Mixer Holdup, and Mixer Capacity. A description of the test, conclusions and recommendations is provided.
Date: April 10, 1952
Creator: Collins, P. E.

Abnormal grain growth in S-816 alloy

Description: From Introduction: "This report presents the results obtained to date of an investigation to establish the fundamental causes of abnormal growth in S-816 alloy under conditions encountered during the forging of blades for the gas turbine of jet engines."
Date: April 1952
Creator: Rush, A I; Freeman, J W & White, A E

Abstract of Paper Presented at the Symposium on Metal ChelateChemistry at Brooklyn Polytechnic Institute on April 26, 1952

Description: The essential structural element which differentiates metal chelate compounds from metal coordination compounds, or metal complexes in general, is the existence of some linkage between two or more of the donor atoms in the first coordination sphere of the metal. It is the purpose of the present discussion to examine the influences that this structural factor may have upon the physical and chemical properties of chelate compounds. Examples of well known, simple coordination compounds involving a variety of donor atoms (Oxygen, nitrogen), as well as a variety of electrostatic situations are shown in the following formula. Below each one are listed a few corresponding chelate structures.
Date: April 1, 1952
Creator: Calvin, Melvin


Description: The amount of Ac/sup 227/ per curie of Ra/sup 226/ was calculated for various values of neutron flux and various Irradiation times. The amount of Th/ sup 228/ produced per curie of Ra/sup 226/ and the percentage of Ac/sup 227/ converted to Th/sup 228/ relative to the total amount of Ac/sup 227/ produced were also calculated. (W.D.M.)
Date: August 28, 1952
Creator: Grove, G. R.; Russell, L. N. & Orr, S. R.

Activation Energy for Fission

Description: The experimentally determined exponential dependence of spontaneous fission rate on Z{sup 2}/A has been used to derive an expression for the dependence of the fission activation energy on Z{sup 2}/A. This expression has been used to calculate the activation energy for slow neutron induced fission and photofission. The correlation with the experimental data on these types of fission seems to be quite good.
Date: August 29, 1952
Creator: Seaborg, Glenn T.

An active particle diffusion theory of flame quenching for laminar flames / Dorothy M. Simon and Frank E. Belles

Description: An equation for quenching distance based on the destruction of chain carriers by the surface is derived. The equation expresses the quenching distance in terms of the diffusion coefficients and partial pressures of the chain carriers and gas phase molecules, the efficiency of the surface as a chain breaker, the total pressure of the mixture, and a constant which depends on the geometry of the quenching surface. Quenching distances measured by flashback for propane-air flames are shown to be consistent with the mechanism. The derived equation is used with the lean inflammability limit and a rate constant calculated from burning velocity data to estimate quenching distances for propane-air (hydrocarbon lean) flames satisfactorily.
Date: March 4, 1952
Creator: Simon, Dorothy M & Belles, Frank E

Aerodynamic characteristics at transonic speeds of a tapered 45 degree sweptback wing of aspect ratio 3 having a full-span flap type of control with overhang balance : transonic-bump method

Description: From Introduction: "This paper presents the aerodynamic characteristics of low-aspect-ratio sweptback wing having a full-span flap type of control employing an overhanging balance of 50 percent of the flap chord.The main purpose of this investigation was to determine if overhang balances are an effective means of reducing the hinge moments of flap type of controls at transonic speeds."
Date: January 25, 1952
Creator: Lockwood, Vernard E & Hagerman, John R

The aerodynamic characteristics at transonic speeds of an all-movable, tapered, 45 degrees sweptback, aspect-ratio-4 tail surface deflected about a skewed hinge axis

Description: From Introduction: "The purpose of the present paper was to determine whether the characteristics about a skewed axis could be predicted from data about the normal angle-of-attack axis, and whether such a configuration offered any aerodynamic advantages over the conventional hinge location normal to the pane of symmetry."
Date: July 3, 1952
Creator: Hammond, Alexander D & Watson, James M

Aerodynamic characteristics of a refined deep-step planing-tail flying-boat hull with various forebody and afterbody shapes

Description: From Introduction: "The results of one phase of this investigation, presented in reference 1, have indicated that hull drag can be reduced without causing large changes in aerodynamic stability and hydrodynamic performance by the use of high length-beam ratios. Another phase of the investigation, reference 2, indicated that hulls of the deep-step planning-tail type have much lower air drag than the conventional type of hull and about the same aerodynamic stability; tank tests, reference 3, have indicated that this type of hull also has hydrodynamic performance equal to and in some respects superior to the conventional type of hull. Unpublished tank tests have indicated that the hull models presented in the present paper (with the possible exception of the forebody alone for which data are not available) will have acceptable hydrodynamic performance."
Date: June 1952
Creator: Riebe, John M & Naeseth, Rodger L

The aerodynamic characteristics of a supersonic aircraft configuration with a 40 degree sweptback wing through a Mach number range from 0 to 2.4 obtained from various sources

Description: A summary and analysis have been made of the results of various investigations to determine the aerodynamic characteristics of a supersonic aircraft configuration. The configuration has a wing with 40 degree sweepback at the quarter-chord line, aspect ratio 4, taper ratio 0.5, and 10-percent-thick circular-arc sections normal to the quarter-chord line. Experimental data were available for a Mach number range from 0.16 to 2.32. Results obtained from wing-flow, rocket-model, transonic-bump, and tunnel tests are presented and, where possible, are supplemented by empirical and theoretical calculations.
Date: April 11, 1952
Creator: Spearman, M. Leroy & Robinson, Ross B.

Aerodynamic characteristics of three deep-step planing-tail flying-boat hulls and a transverse-step hull with extended afterbody

Description: From Summary: "An investigation was made to determine the aerodynamic characteristics in the presence of a wing of three-step planning-tail flying-boat hulls which differed only in the amount of step fairing. The purpose of comparison, tests were also made of a transverse-step hull with an extended afterbody."
Date: August 1952
Creator: Riebe, John M & Naeseth, Rodger L