UNT Libraries Government Documents Department - 41 Matching Results

Search Results

Constant-pressure blowers

Description: The conventional axial blowers operate on the high-pressure principle. One drawback of this type of blower is the relatively low pressure head, which one attempts to overcome with axial blowers producing very high pressure at a given circumferential speed. The Schicht constant-pressure blower affords pressure ratios considerably higher than those of axial blowers of conventional design with approximately the same efficiency.
Date: January 1940
Creator: Sörensen, E.

DFS dive-control brakes for gliders and airplanes ; and, Analytical study of the drag of the DFS dive-control brake

Description: These two reports are surveys on the progress and present state of development of dive-control flaps for gliders and airplanes. The second article describes how on the basis of wind tunnel and free-flight tests, the drag increase on brake flaps of the type DFS, can be predicted. Pressure records confirm a two-dimensional load distribution along the brake-flap surface Aerodynamically, the location of the brake flaps along the span is of importance for reasons of avoidance of vibration and oscillation phenomena on control and tail surfaces; statically, because of the magnitude of the frontal drag in diving with respect to the bending moments, which may become decisive for the dimensions of the wing attachment and for the wing covering.
Date: January 1, 1940
Creator: Jacobs, Hans & Wanner, Adolf

Effect of Wing Loading, Aspect Ratio, and Span Loading of Flight Performances

Description: "An investigation is made of the possible improvements in maximum, cruising, and climbing speeds attainable through increase in the wing loading. The decrease in wing area was considered for the two cases of constant aspect ratio and constant span loading. For a definite flight condition, an investigation is made to determine what loss in flight performance must be sustained if, for given reasons, certain wing loadings are not to be exceeded. With the aid of these general investigations, the trend with respect to wing loading is indicated and the requirements to be imposed on the landing aids are discussed" (p. 1).
Date: January 1940
Creator: Göthert, B.

Knocking in an internal-combustion engine

Description: The question remains open of the relation between the phenomena of knocking in the engine and the explosion wave. The solution of this problem is the object of this paper. The tests were conducted on an aircraft engine with a pyrex glass window in the cylinder head. Photographs were then taken of various combinations of fuels and conditions.
Date: January 1, 1940
Creator: Sokolik, A & Voinov, A

Aerodynamics of rotating-wing aircraft with blade-pitch control

Description: From Introduction: "In the present report, with the aid of the usual computation methods, a rotor is investigated the pitch of whose blades is capable of being controlled in such a manner that it varies linearly with the flapping angle. To test the effect of this linkage on the aircraft performance, the theory is applied to an illustrative example."
Date: February 1940
Creator: Pfluger, A

The strength of shell and tubular spar wings

Description: The report is a survey of the strength problems arising on shell and tubular spar wings. The treatment of the shell wing strength is primarily confined to those questions which concern the shell wing only; those pertaining to both shell wing and shell body together have already been treated in TM 838. The discussion of stress condition and compressive strength of shell wings and tubular spar wings is prefaced by several considerations concerning the spar and shell design of metal wings from the point of view of strength.
Date: February 1, 1940
Creator: Ebner, H

Testing of high-octane fuels in the single-cylinder airplane engine

Description: One of the most important properties of aviation fuels for spark-ignition engines is their knock rating. The CFR engine tests of fuels of 87 octane and above does not always correspond entirely to the actual behavior of these fuels in the airplane engine. A method is therefore developed which, in contrast to the octane number determination, permits a testing of the fuel under various temperatures and fuel mixture conditions. The following reference fuels were employed: 1) Primary fuels; isooctane and n-heptane; 2) Secondary fuels; pure benzene and synthetic benzine.
Date: February 1, 1940
Creator: Seeber, Fritz

Application of the methods of gas dynamics to water flows with free surface I : flows with no energy dissipation

Description: The application is treated in sufficient detail to facilitate as much as possible its application by the engineer who is less familiar with the subject. The present work was undertaken with two objects in view. In the first place, it is considered as a contribution to the water analogy of gas flows, and secondly, a large portion is devoted to the general theory of the two-dimensional supersonic flows.
Date: March 1940
Creator: Preiswerk, Ernst

Application of the methods of gas dynamics to water flows with free surface II : flows with momentum discontinuities (hydraulic jumps)

Description: In this paper an introduction to shock polar diagrams is given which then leads into an examination of water depths in hydraulic jumps. Energy loss during these jumps is considered along with an extended look at elementary solutions of flow. An experimental test set-up is described and the results presented.
Date: March 1940
Creator: Preiswerk, Ernst

Measurement of Knock Characteristics in Spark-Ignition Engines

Description: This paper presents a discussion of three potential sources of error in recording engine knocking which are: the natural oscillation of the membrane, the shock process between test contacts, and the danger of burned contacts. Following this discussion, the paper calls attention to various results which make the bouncing-pin indicator appear fundamentally unsuitable for recording knock phenomena.
Date: March 1940
Creator: Schütz, R.

The Shock-Absorbed System of the Airplane Landing Gear

Description: "A discussion is given of the behavior of the shock-absorbing system, consisting of elastic struts and tires, under landing, take-off, and taxying conditions, and a general formula derived for obtaining the minimum stroke required to satisfy the conditions imposed on the landing gear. Finally, the operation of some typical shock-absorbing systems are examined and the necessity brought out for taking into account, in dynamic landing-gear tests, the effect of the wing lift at the instant of contact with the ground" (p. 1).
Date: March 1940
Creator: Callerio, Pietro

Stresses in single-spar wing constructions with incompletely built-up ribs

Description: It is shown that the force distribution resulting from incomplete ribs in single spar wing structures may be determined with the aid of the shear field method by a statistically indeterminate computation. A numerical computation is given of the force distribution of a wing structure whose two neighboring incomplete ribs with web missing in half the section are torsionally loaded.
Date: March 1940
Creator: Reinitzhuber, F.

The Lead Susceptibility of Fuels and Its Dependence on the Chemical Composition

Description: The fact that by the use of tetraethyl lead a number of otherwise unsuitable fuels could be made to meet engine requirements was not sufficiently appreciated. While use of tetraethyl lead is limited, the addition of special leaded fuels that increase the octane number is a requirement for many fuels. In this connection, the extent to which the action of tetraethyl lead through the addition of knock-resistant hydrocarbons to the base gasoline is influenced, is quite important. To the elucidation of this problem and of the storage stability of leaded fuels, the present report is dedicated.
Date: April 1940
Creator: Widmaier, O.

The torsion of box beams with one side lacking

Description: The torsion of box beams of rectangular section, the edges of which are strengthened by flanges, and of which one side is lacking, is analyzed by the energy method. The torsional stresses are generally taken up by the bending of the two parallel walls, the rigidity of which is augmented by the third wall. The result was checked experimentally on duralumin and plywood boxes. The torsion recorded was 10 to 30 percent less than that given by the calculation, owing to self-stiffening.
Date: April 1, 1940
Creator: Cambilargiu, E

On the theory of unsteady planing and the motion of a wing with vortex separation

Description: The disturbance imparted to water by a planing body give rise to a wave form of motion on the free surface, the length of the waves increasing indefinitely with increase in the Froude number and being directly proportional to the latter in the case of the plane or two-dimensional problem. At large Froude numbers the effect of the weight shows up to any appreciable extent only at some distance from the body, so that the flow near the body can be considered as part of a flow of an infinitely extending weightless fluid. This paper is a consideration of these characteristics as well as a formulation of the planing problem and its relation to the problem of a thin wing.
Date: May 1940
Creator: Sedov, L.

Some data on the static longitudinal stability and control of airplanes : design of control surfaces

Description: In the solution of a number of problems on the stability and controllability of airplanes, there arises the necessity for knowing the characteristics of the tail surfaces of the types in common use today. Of those characteristics, the most important are the effectiveness and hinge moments of the tail surfaces. As has been shown in the present paper, there exists the possibility of determining these characteristics by the formulas obtained with a degree of accuracy sufficient for the purposes of preliminary computation. These formulas take into account a number of fundamental tail characteristics such as tail cut-outs on the control surface and the form of the control surface leading edge.
Date: May 1, 1940
Creator: Martinov, A & Kolosov, E

Italian high-speed airplane engines

Description: This paper presents an account of Italian high-speed engine designs. The tests were performed on the Fiat AS6 engine, and all components of that engine are discussed from cylinders to superchargers as well as the test set-up. The results of the bench tests are given along with the performance of the engines in various races.
Date: June 1, 1940
Creator: Bona, C F

Tests of lead-bronze bearings in the DVL bearing-testing machine

Description: The lead-bronze bearings tested in the DVL machine have proven themselves very sensitive to load changes as in comparison with bearings of light metal. In order to prevent surface injuries and consequently running interruptions, the increase of the load has to be made in small steps with sufficient run-in time between steps. The absence of lead in the running surface, impurities in the alloy (especially iron) and surface irregularities (pores) decreases the load-carrying capacity of the bearing to two or three times that of the static load.
Date: June 1, 1940
Creator: Fischer, G

Experimental results with airfoils tested in the high-speed tunnel at Guidonia

Description: The results are presented of a triple series of tests using force measurements, pressure-distribution measurements, and air flow photographs on airfoil sections suitably selected so that comparison could be made between the experimental and theoretical results. The comparison with existing theory is followed by a discussion of the divergences found, and an attempt is made to find their explanation.
Date: July 1, 1940
Creator: Ferri, Antonio

Experiments on Ball and Roller Bearings Under Conditions of High Speed and Small Oil Supply

Description: This report describes a testing machine on which 35 millimeter bearings (bore) can be run at speeds of the order of 21,000 rpm, while the following factors are recorded: 1) oil circulation through bearing and oil temperature. 2) maximum temperature of outer bearing ring, 3) radial and axial load on bearing, 4) radial, axial, and angular clearance of bearing, 5) power consumption of bearing. The experiments show that the lubrication was most reliable and oil consumption lowest when the oil was introduced through a hole in the outer or inner ring of the bearing.
Date: July 1940
Creator: Getzlaff, Günter

New Equipment for Testing the Fatigue Strength of Riveted and Welded Joints

Description: "The mechanical and electrical construction of a new experimental instrument for fatigue testing riveted and welded joints is described. This experimental device has the advantage of being able to stress, even with comparatively low magnetic exciter force, structural components in alternate bending by resonance vibrations up to incipient fatigue failure (p .1)".
Date: July 1940
Creator: Müller, W

The maximum delivery pressure of single-stage radial superchargers for aircraft engines

Description: With the aid of simple considerations and test results, an attempt is made to clear up some obscure points that still exist. The considerations are restricted to those cases where it is in fact of advantage to"force" the large delivery heads required for high altitude and high supercharge with a single-stage supercharger.
Date: August 1940
Creator: von der Nüll, W.