UNT Libraries Government Documents Department - Browse


Airplane dopes and doping

Description: Cellulose acetate and cellulose nitrate are the important constituents of airplane dopes in use at the present time, but planes were treated with other materials in the experimental stages of flying. The above compounds belong to the class of colloids and are of value because they produce a shrinking action on the fabric when drying out of solution, rendering it drum tight. Other colloids possessing the same property have been proposed and tried. In the first stages of the development of dope, however, shrinkage was not considered. The fabric was treated merely to render it waterproof. The first airplanes constructed were covered with cotton fabric stretched as tightly as possible over the winds, fuselage, etc., and flying was possible only in fine weather. The necessity of an airplane which would fly under all weather conditions at once became apparent. Then followed experiments with rubberized fabrics, fabrics treated with glue rendered insoluble by formaldehyde or bichromate, fabrics treated with drying and nondrying oils, shellac, casein, etc. It was found that fabrics treated as above lost their tension in damp weather, and the oil from the motor penetrated the proofing material and weakened the fabric. For the most part the film of material lacked durability. Cellulose nitrate lacquers, however were found to be more satisfactory under varying weather conditions, added less weight to the planes, and were easily applied. On the other hand, they were highly inflammable, and oil from the motor penetrated the film of cellulose nitrate, causing the tension of the fabric to be relaxed.
Date: January 1, 1919
Creator: Smith, W H

Annual report of the National Advisory Committee for Aeronautics (2nd) together with the message of the President of the United States transmitting the report for the fiscal year ending June 30, 1916. administrative report including technical report

Description: Report includes the National Advisory Committee for Aeronautics letter of submittal to the President, Congressional report, summaries of the committee's activities and research accomplished, expenditures, problems, recommendations and a compilation of technical reports produced.
Date: 1917

Airplane Stress Analysis

Description: Report presents stress analysis of individual components of an airplane. Normal and abnormal loads, sudden loads, simple stresses, indirect simple stresses, resultant unit stress, repetitive and equivalent stress, maximum steady load and stress are considered.
Date: January 1, 1918
Creator: Zahm, A F & Crook, L H

The Limiting Velocity in Falling from a Great Height

Description: The purpose of this report is to give a simple treatment of the problem of calculating the final or limiting velocity of an object falling in vertical motion under gravity in a resisting medium. The equations of motion are easily set up and integrated when the density of the medium is constant and the resistance varies as the square of the velocity. The results show that the fundamental characteristics of the vertical motion under gravity in a resisting medium is the approach to a terminal or limiting velocity, whether the initial downward velocity is less or greater than the limiting velocity. This method can be used to calculate the terminal velocity of a bomb trajectory.
Date: January 1, 1919
Creator: Wilson, Edwin Bidwell

Report on behavior of aeroplanes in gusts

Description: Part 1 presents the results of a wind tunnel test of a biplane model with an 18 inch span. The lift, drift, and pitching moment were measured for a series of angles of incidence corresponding to the maximum possible changes of flight attitude. Only the discussion of symmetrical or longitudinal changes is given. From the observed rate of variation of the forces and pitching moment, it was possible to calculate the derivatives needed in the complete theory of longitudinal stability in still air. The damping of the pitching oscillation was also determined experimentally. Part 2 presents a theoretical method for determining the effects of gusts on aeroplanes in the following cases: (1) head-on gusts rising from 0 to j feet per second with various degrees of sharpness, (2) up gusts of the same type, (3) rotary gusts of the same type, (4) rear gusts and down gusts are included by merely changing the sign of j.
Date: January 1, 1917
Creator: Hunsaker, J C & Wilson, Edward Bidwell

Theory of an Airplane Encountering Gusts III

Description: Report presents a new method for solving linear equations developed by Bromwich, which is suited to determine the motion for any particular gust, when the machine started from equilibrium, without the trouble of determining the constants of integration in the complementary function. (author).
Date: January 1, 1918
Creator: Wilson, Edwin Bidwell

An investigation of the elements which contribute to statical and dynamical stability, and of the effects of variation in those elements

Description: Part 1 gives details of models tested and methods of testing of the Eiffel 36 wing alone and the JN2 aircraft. Characteristics and performance curves for standard JN are included. Part 2 presents a statistical analysis of the following: lift and drag contributed by body and chassis tested without wings; lift and drag contributed by tail, tested without wings; the effect on lift and drift of interference between the wings of a biplane combination; lift and drag contributed by the addition of body, chassis, and tail to a biplane combination; total parasite resistance; effect of varying size of tail, keeping angle of setting constant; effect of varying length of body and size of tail at the same time, keeping constant moment of tail surface about the center of gravity; forces on the tail and the effects of downwash; effect of size and setting of tail on statical longitudinal stability effects of length of body on stability; the effects of the various elements of an airplane on longitudinal stability and the placing of the force vectors. Part 3 presents the fundamental principals of dynamical stability; computations of resistance derivatives; solution of the stability equation; dynamical stability of the Curtiss JN2; tabulation of resistance derivatives; discussion of the resistance derivatives; formation and solution of stability equations; physical conceptions of the resistance derivatives; elements contributing to damping and an investigation of low speed conditions. Part 4 includes a summary of the results of the statistical investigation and a summary of the results for dynamic stability.
Date: January 1, 1918
Creator: Klemin, Alexander; Warner, Edward P. & Denkinger, George M.

Thermodynamic efficiency of present types of internal combustion engines for aircraft

Description: Report presents requirements of internal combustion engines suitable for aircraft. Topics include: (1) service requirements for aeronautic engines - power versus weight, reliability, and adaptability factors, (2) general characteristics of present aero engines, (3) aero engine processes and functions of parts versus power-weight ratio, reliability, and adaptability factors, and (4) general arrangement, form, proportions, and materials of aero parts - power-weight ratio, reliability, and adaptability.
Date: January 1, 1917
Creator: Lucke, Charles E.

The airplane tensiometer

Description: Certain parts of an airplane are subjected not only to the stresses imposed by the aerodynamic or flying load, but also to the initial stresses, caused by the tension in the stay and drift wires. Report describes a tensiometer that measures such stresses which is simple in construction, accurate, and easily and quickly operated even by inexperienced persons. Two sizes of the instrument are available. One is suitable for wires up to one-fourth inch in diameter and the other for wires from one-fourth to three-eights inch in diameter.
Date: 1919
Creator: Larson, L J

Temperatures in Spark Plugs Having Steel and Brass Shells

Description: This investigation was conducted at the Bureau of Standards for the National Advisory Committee for Aeronautics. Brass has often been assumed superior to steel for spark plug shells because of its greater heat conductivity. The measurements described in this report prove the contrary, showing that the interior of a spark plug having a brass shell is from 50 degrees to 150 degrees c. (90 degrees to 270 degrees f.) hotter than that of a similar steel plug. Consistent results were obtained in both an aviation and a truck engine, and under conditions which eliminated all other sources of difference between the plugs. It is to be concluded that steel is to be preferred to brass for spark plug shells. This report embodies the results of measurements taken of electrodes and a comparison of brass and steel insulators of spark plugs while they were in actual operation. The data throw considerable light upon the problem of the proper control of temperatures in these parts.
Date: January 1, 1919
Creator: Cragoe, C S

Fabrics for aeronautic construction

Description: The Bureau of Standards undertook the investigation of airplane fabrics with the view of finding suitable substitutes for the linen fabrics, and it was decided that the fibers to be considered were cotton, ramie, silk, and hemp. Of these, the cotton fiber was the logical one to be given primary consideration. Report presents the suitability, tensibility and stretching properties of cotton fabric obtained by laboratory tests.
Date: January 1, 1918
Creator: Walen, E D