UNT Libraries Government Documents Department - 176 Matching Results

This system will be undergoing maintenance April 18th between 9:00AM and 12:00PM CDT.

Search Results

Results: 1 - 24 next
open access

Tests of a Heated Low-Drag Airfoil

Description: Report discusses the results of an experimental investigation into the NACA 65,2-016 heated wing. Information about the effect of heating on the drag coefficients, Reynolds numbers, and stability of the laminar boundary layer.
Date: December 1942
Creator: Frick, Charles W., Jr. & McCullough, George B.
Item Type: Refine your search to only Report
open access

Pressure-Distribution Measurements of a Model of a Davis Wing Section with Fowler Flap Submitted by Consolidated Aircraft Corporation

Description: Wing pressure distribution diagrams for several angles of attack and flap deflections of 0 degrees, 20 degrees, and 40 degrees are presented. The normal force coefficients agree with lift coefficients obtained in previous test of the same model, except for the maximum lifts with flap deflection. Pressure distribution measurements were made at Reynolds Number of about 6,000,000.
Date: January 1942
Creator: Abbott, Ira H.
Item Type: Refine your search to only Report
open access

Pressure-distribution measurements of two airfoil models with Fowler flaps submitted by Consolidated Aircraft Corporation as alternative wing sections of the XB-32 airplane

Description: Report presenting pressure distribution measurements on two 24-inch chord models equipped with Fowler flaps in the two-dimensional low-turbulence pressure tunnel. Results regarding pressure-distribution diagrams and normal-force and moment coefficients are provided.
Date: January 1942
Creator: Abbott, Ira H.
Item Type: Refine your search to only Report
open access

A study of the application of data on various types of flap to the design of fighter brakes

Description: Report presenting an approximate method of applying the available data on various types of flaps in the design of fighter brakes together with several examples of its use. The computed effects of flap type, size, location, and deflection as well as the effects of altitude and initial velocities on braking characteristics are also shown in some examples using the method to determine various flap arrangements.
Date: June 1942
Creator: Purser, Paul E.
Item Type: Refine your search to only Report
open access

Calculation of tab characteristics for flight conditions from wind-tunnel data

Description: Report presenting tail-surface characteristics calculated from wind-tunnel data, which have been reported to not correspond with flight-test measurements. The primary problem under consideration is the calculation of the effect of tab deflection on the free-floating angle of the elevator, as in a servocontrol.
Date: April 1942
Creator: Sears, Richard I.
Item Type: Refine your search to only Report
open access

Wind-tunnel investigation of control-surface characteristics 5: the use of a beveled trailing edge to reduce the hinge moment of a control surface

Description: Report presenting wind tunnel testing to investigate the possibility of reducing the hinge moments of a control surface by beveling the trailing edge. Tests were made with a 9-percent-thick airfoil with a 30-percent-chord plain flap. Results regarding the variations of lift and hinge moment, effect of shapes, and pitching moments are provided.
Date: March 1942
Creator: Jones, Robert T. & Ames, Milton B., Jr.
Item Type: Refine your search to only Report
open access

Wind tunnel investigation of control surface characteristics 9: some analytical considerations and experimental test results for an internally balanced flap

Description: Report presenting an analysis of the probable aerodynamic section characteristics of a plain flap with various arrangements of internal balance. The results of the calculations previously obtained were found to be in agreement with the experiment. Some possible applications of the data to balancing tabs are also provided.
Date: July 1942
Creator: Sears, Richard I.
Item Type: Refine your search to only Report
open access

Wind tunnel investigation of control-surface characteristics 10: a 30-percent-chord plain flap with straight contour on the NACA 0015 airfoil

Description: Report presenting force-test measurements in two-dimensional flow in the 4- by 6-foot vertical tunnel to determine the characteristics of an NACA 0015 airfoil equipped with a straight-contour plain flap with a chord 30 percent of the airfoil chord. Results regarding the lift, hinge moment of flap, pitching moment, and drag are provided.
Date: September 1942
Creator: Hoggard, H. Page, Jr.
Item Type: Refine your search to only Report
open access

Wind-tunnel investigation of control-surface characteristics 6: a 30-percent-chord plain flap on the NACA 0015 airfoil

Description: Report presenting force-test measurements in two-dimensional flow in the 4- by 6-foot vertical tunnel of the characteristics of an NACA 0015 airfoil equipped with a plain flap with a chord 30 percent of the airfoil chord and a plain tab with a chord 20 percent of the flap chord. Results regarding lift, hinge moment of flap, pitching moment, drag, and tab characteristics are provided.
Date: June 1942
Creator: Sears, Richard I. & Liddell, Robert B.
Item Type: Refine your search to only Report
open access

Wind-Tunnel Investigation of Control-Surface Characteristics: [Part] 7 - A Medium Aerodynamic Balance of Two Nose Shapes Used With a 30-Percent-Chord Flap on an NACA 0015 Airfoil

Description: Report presenting force-test measurements in two-dimensional flow made in the 4- by 6-foot vertical tunnel of the characteristics of an NACA 0015 airfoil with a balanced flap with a chord 30 percent of the airfoil chord and a flap-nose overhang 35 percent of the flap chord. Results regarding lift, hinge moment of flap, pitching moment, drag, and tab characteristics are provided.
Date: July 1942
Creator: Sears, Richard I. & Hoggard, H. Page, Jr.
Item Type: Refine your search to only Report
open access

Wind-Tunnel Investigation of an NACA 23012 Airfoil with a Handley Page Slat and Two Flap Arrangements

Description: Report presenting an investigation in the 7- by 10-foot wind tunnel of an NACA 23012 airfoil equipped with a Handley Page slat and a slotted and a split flap. The purpose of the investigation was to determine the aerodynamic section characteristics of the airfoil with and without flaps as affected by the location of the Handley Page slat. A range of slat-nose locations was investigated both with and without flaps at a constant slat gap.
Date: February 1942
Creator: Schuldenfrei, Marvin J.
Item Type: Refine your search to only Report
open access

Wind tunnel investigation of a plain aileron with various trailing-edge modifications on a tapered wing 2: ailerons with thickened and beveled trailing edges

Description: Report presenting an investigation in the 7- by 10-foot tunnel of various modifications to the trailing edge of a 0.155-chord plain aileron on a semispan model of the tapered wing of a fighter airplane. The stick forces and rates of roll were estimated for a fighter airplane with the plain and modified ailerons.
Date: October 1942
Creator: Rogallo, F. M. & Purser, Paul E.
Item Type: Refine your search to only Report
open access

Characteristics of plain and balanced elevators on a typical pursuit fuselage at attitudes simulating normal-flight and spin conditions

Description: Report presenting lift and elevator hinge-moment characteristics of a horizontal tail with various plain and balanced elevators and mounted on a typical pursuit fuselage as measured in the 7- by 10-foot wind tunnel at attitudes simulating normal-flight and spin conditions. The lift effectiveness of the elevator was practically independent of the size of the aerodynamic balance. Results regarding the fuselage alone and fuselage interference, lift characteristics of fuselage-tail combinations, li… more
Date: March 1942
Creator: Sears, Richard I. & Hoggard, H. Page, Jr.
Item Type: Refine your search to only Report
open access

Characteristics of beveled-trailing-edge elevators on a typical pursuit fuselage at altitudes simulating-normal flight and spin conditions

Description: Report presenting lift and elevator hinge-moment characteristics were measured on horizontal tail provided with elevators having three different beveled trailing edges. Results regarding fuselage alone and fuselage interference, lift characteristics of fuselage-tail combination, elevator hinge-moment characteristics, drag, and comparison with data from two-dimensional-flow tests are provided.
Date: December 1942
Creator: Gillis, Clarence L.
Item Type: Refine your search to only Report
open access

Application of Balancing Tabs to Ailerons

Description: Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effe… more
Date: June 1942
Creator: Sears, Richard I.
Item Type: Refine your search to only Report
open access

Wind-tunnel investigation of control-surface characteristics 8: a large aerodynamic balance of two nose shapes used with a 30-percent-chord flap on an NACA 0015 airfoil

Description: Report presenting force tests in two-dimensional flow in the 4- by 6-foot vertical tunnel of the characteristics of an NACA 0015 airfoil with a balanced flap having a chord of 30 percent of the airfoil chord, a flap-nose overhang 50 percent of the flap chord, and a tab having a chord 20 percent of the flap chord. Results regarding the precision and presentation of data, lift, hinge moment of flap, pitching moments, drag, tab characteristics, and balancing effectiveness of various overhangs are … more
Date: July 1942
Creator: Sears, Richard I. & Gillis, Clarence L.
Item Type: Refine your search to only Report
open access

The Effect of Various Surface Conditions on Press Fits of Steel Bushings and 17S-T Aluminum-Alloy Fittings

Description: Report presenting testing of specimens of 17S-T aluminum-alloy fittings with pressed-in steel bushings for various surface conditions. The surface conditions tested included bare surfaces, aonidcal coating and steel cadmium-plate, and one surface treated and the other bare, both without lubrication and with Gredag No. 83 as a lubricant. The calculated coefficients of friction for the various press fits for the investigation ranged from 0.33 for the unlubricated contact of bare steel and aluminu… more
Date: December 1942
Creator: Hartmann, E. C. & Reedy, J. F.
Item Type: Refine your search to only Report
open access

Progress Summary Number 1: Mechanical Properties of Flush-Riveted Joints Submitted by Five Airplane Manufacturers

Description: Summary presenting information on flush-riveted joints for aircraft construction, including the strength, occurrence of defects, and effect of the angle of rivet head. The current tests covers specimens from 15 manufacturers of which 5 series have been completed and are described in this report.
Date: February 1942
Creator: Brueggeman, William Charles
Item Type: Refine your search to only Report
open access

The Porpoising Characteristics of a Planing Surface Representing the Forebody of a Flying-Boat Hull

Description: Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.
Date: May 1942
Creator: Benson, James M.
Item Type: Refine your search to only Report
open access

An Investigation of Hydrofoils in the NACA Tank 1: Effect of Dihedral and Depth of Submersion

Description: Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.
Date: September 1942
Creator: Benson, James M. & Land, Norman S.
Item Type: Refine your search to only Report
open access

The effect of dead rise upon the low-angle type of porpoising

Description: Report presenting data pertaining to forces and moments developed by V-bottom planing surfaces of different angles of dead rise in order to compute the effect of dead rise on the lower trim limit of stability on a seaplane. Increase of angle of dead rise in the range of 10 degrees to 30 degrees causes an important increase in the lower limit of stability.
Date: October 1942
Creator: Benson, James M. & Lina, Lindsay J.
Item Type: Refine your search to only Report
Back to Top of Screen