UNT Libraries Government Documents Department - 1,263 Matching Results

Search Results

Tests of a heated low-drag airfoil

Description: Report discusses the results of an experimental investigation into the NACA 65,2-016 heated wing. Information about the effect of heating on the drag coefficients, Reynolds numbers, and stability of the laminar boundary layer.
Date: December 1942
Creator: Frick, Charles W., Jr. & McCullough, George B.

Shear tests on DuPont explosive rivets with the countersunk head milled flush after expansion

Description: Report discusses the results of shear testing in which the heads of Du Pont explosive countersunk rivets were allowed to protrude above the skin surface before expansion and the protruding portions were removed after expansion. As the height of the rivet head above the skin increases, the tightness of the rivet was found to increase. The report concludes that it may be desirable to investigating filling an entire shank with an explosive charge in order to permit greater tolerances in the drilled hole diameter and still have consistently tight rivets.
Date: May 1943
Creator: Gottieb, Robert & Bartone, Leonard M.

The Porpoising Characteristics of a Planing Surface Representing the Forebody of a Flying-Boat Hull

Description: Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.
Date: May 1, 1942
Creator: Benson, James M.

Some systematic model experiments of the bow-spray characteristics of flying-boat hulls operating at low speeds in waves

Description: Report discusses the results of testing on several models of flying boats, the XPB2M-1, the XPBB-1, the JRM-1, and 11 other models to determine the effect of bow form on the amount of spray thrown onto the windshield of a flying boat in rough water. Several recommendations for reducing the height and volume of spray are provided. Any change in the hull form that softens the impact between the hull and waves seems to reduce the spray.
Date: December 1943
Creator: Locke, F. W. S., Jr

An Investigation of Hydrofoils in the NACA Tank I : Effect of Dihedral and Depth of Submersion

Description: Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.
Date: September 1, 1942
Creator: Land, Norman S. & Benson, James M.

Tests of hydraulically expanded rivets

Description: Report discusses the results of an investigation into the tightness, shear strength, tensile strength, and life under pulsating loads of hollow, hydraulically expanded rivets made of 17S-T aluminum alloy. The countersunk-head rivets with inserts had a much higher maximum load in shear than the modified-roundhead rivets, which did not have inserts.
Date: March 1944
Creator: Mandel, Merven W.; Crate, Harold & Schuette, Evan H.

Tensile Tests of NACA and Conventional Machine- Countersunk Flush Rivets

Description: An investigation was conducted to determine and compare the tensile strength of NACA and conventional machine-countersunk flush rivets of several rivet-head angles and varying countersunk depth. The results of the investigation are presented in the form of curves that show the variation of the tensile strength of the rivet with the ratio of the sheet thickness to the rivet diameter. For the same rivet-head angle and for a given angle of c/d, the NACA rivets developed higher tensile strength than the conventional rivets.
Date: October 1, 1944
Creator: Bartone, Leonard M. & Mandel, Merven W.

A preliminary study of machine-countersunk flush rivets subjected to a combined static and alternating shear load

Description: Report discusses the results of an investigation to study the effect of the height of a rivet head on the number of cycles required to cause failure of a machine-countersunk flush-riveted joint under a combined static and alternating shear load. A tight joint and a loose joint were tested and the number of cycles to failure and location of fatigue failure were compared.
Date: December 1943
Creator: Crate, Harold

Comparative tests of the strength and tightness of commercial flush rivets of one type and NACA flush rivets in machine-countersunk and counterpunched joints

Description: Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.
Date: February 1, 1944
Creator: Mandel, Merven W.

Flight measurements by various methods of the drag characteristics of the XP-51 airplane

Description: Report discussing measurements of the overall drag coefficient of the XP-51 in dives using three different methods. The three instruments used to measure drag variation are compared for accuracy. A comparison of the drag results obtained from this test are also compared to the results obtained from previous wind tunnel testing.
Date: June 1946
Creator: Pearson, Henry A. & Beadle, Dorothy E.