UNT Libraries Government Documents Department - Browse

ABOUT BROWSE FEED

Abnormal grain growth in M-252 and S-816 alloys

Description: Report discussing an experimental investigation was carried out on air- and vacuum-melted M-252 and S-816 alloys to find conditions of heating and hot-working which resulted in abnormal grain growth. The experiments were mainly limited to normal conditions of heating for hot-working and heat treatment and normal temperatures of solution treatment were used to allow grain growth after susceptibility to abnormal grain growth was developed by various experimental conditions. Results indicated that small reductions of essentially strain-free metal were the basic cause of such grain growth.
Date: November 1957
Creator: Decker, R F; Rush, A I; Dano, A G & Freeman, J W

Abnormal grain growth in nickel-base heat-resistant alloys

Description: From Introduction: "The data included in this report for Nimonic 80A alloy, for instance, represent experiments carried out to help clarify a production problem of grain-size control in an alloy which has been extensively used. The general procedure of the investigation was to carry out controlled laboratory experiments on samples of bar stock to find conditions of heating and hot-working which resulted in abnormal grain growth."
Date: December 1957
Creator: Decker, R F; Rush, A I; Dano, A G & Freeman, A G

Abnormal grain growth in S-816 alloy

Description: From Introduction: "This report presents the results obtained to date of an investigation to establish the fundamental causes of abnormal growth in S-816 alloy under conditions encountered during the forging of blades for the gas turbine of jet engines."
Date: April 1952
Creator: Rush, A I; Freeman, J W & White, A E

Accelerations in transport-airplane crashes

Description: From Introduction: "A study of crash-impact survival in light airplanes is reported in references 1 and 2. A similar study for fighter airplanes is reported in reference 3. This report discusses crash-impact survival in transport airplanes."
Date: February 1958
Creator: Preston, G Merritt & Pesman, Gerard J

Acoustic analysis of ram-jet buzz

Description: From Introduction: "The surging of a system containing a centrifugal- or axial-flow compressor (e.g., refs. 1 to 4) is an example of self-sustained oscillation. Inlets designed for supersonic jet engines also have been observed to induce oscillations (e.g., refs. 5 to 11) which are usually referred to as "buzz." The origin of buzz in ram-jet engines is the subject of the present report."
Date: November 1955
Creator: Mirels, Harold

Acoustic radiation from two-dimensional rectangular cutouts in aerodynamic surfaces

Description: From Introduction: "The experiments in high-speed flow showed that an intense, high-frequency acoustic radiation is an essential feature of the problem. Consequently, a study of the acoustic field (involving schlieren observations and frequency and intensity measurements) was undertaken. This report presents the salient features of the study, which was mainly exploratory."
Date: August 1955
Creator: Krishnamurty, K

Acoustic, thrust, and drag characteristics of several full-scale noise suppressors for turbojet engines

Description: From Introduction: " Considerable analytical and experimental research has been done to find means of reducing the noise levels of the turbojet transports. Noise levels can be decreased by engine redesign to reduce the jet-exit velocity (ref. 1), proper flight-climb techniques (ref. 2), and the use of noise-suppression exhaust nozzles (refs. 3 to 5). The present report is concerned with the last method."
Date: April 1958
Creator: Ciepluch, Carl C; North, Warren J; Coles, Willard D & Antl, Robert J

Additional static and fatigue tests of high-strength aluminum-alloy bolted joints

Description: From Introduction: "Early in 1951 the National Advisory Committee for Aeronautics published, as Technical Note 2276 (ref. 1), a report by the Aluminum Research Laboratories of the Aluminum Company of America on the results of static and fatigue tests of high-strength aluminum alloy monobloc specimens and bolted joints. In view of special interest shown by several aircraft companies, certain expansions of the test program were undertaken by the Aluminum Research Laboratories and are reported herein."
Date: July 1954
Creator: Hartmann, E C; Holt, Marshall & Eaton, I D

Aerodynamic characteristics and flying qualities of a tailless triangular-wing airplane configuration as obtained from flights of rocket-propelled models at transonic and supersonic speeds

Description: Report discussing a flight investigation of rocket-powered models of a tailless triangular-wing airplane configuration was made through the transonic and low supersonic speed range at the Langley Pilotless Aircraft Research Station at Wallops Island, Va. An analysis of the aerodynamic coefficients, stability derivatives, and flying qualities based on the results obtained from the successful flight tests of three models is presented.
Date: November 1956
Creator: Mitcham, Grady L; Stevens, Joseph E & Norris, Harry P

Aerodynamic characteristics of a circular cylinder at Mach number 6.86 and angles of attack up to 90 degrees

Description: Pressure-distribution and force tests of a circular cylinder have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.88, a Reynolds number of 129,000, and angles of attack up to 90 degrees. The results are compared with the hypersonic approximation of Grimminger, Williams, and Young and a simple modification of the Newtonian flow theory. An evaluation of the crossflow theory is made through comparison of present results with available crossflow Mach number drag coefficients.
Date: January 1957
Creator: Penland, Jim A

Aerodynamic characteristics of a refined deep-step planing-tail flying-boat hull with various forebody and afterbody shapes

Description: An investigation was made in the Langley 300-mph 7- by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes and, for comparison, a streamline body simulating the fuselage of a modern transport airplane. The results of the tests indicated that the configurations incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the configurations incorporating a forebody with length-beam ratio of 5. The lowest minimum drag coefficients, which were considerably less than that of a conventional hull and slightly less than that of a streamline body, were obtained on the length-beam-ratio-7 forebody, alone and with round center boom. Drag coefficients and longitudinal- and lateral-stability parameters presented include the interference of a 21-percent-thick support wing.
Date: June 1952
Creator: Riebe, John M & Naeseth, Rodger L

Aerodynamic characteristics of a two-blade NACA 10-(3)(062)-045 propeller and of a two-blade NACA 10-(3)(08)-045 propeller

Description: Characteristics are given for the two-blade NACA 10-(3)(062)-045 propeller and for the two-blade NACA 10-(3)(08)-045 propeller over a range of advance ratio from 0.5 to 3.8, through a blade-angle range from 20 degrees to 55 degrees measured at the 0.75 radius. Maximum efficiencies of the order of 91.5 to 92 percent were obtained for the propellers. The propeller with the thinner airfoil sections over the outboard portion of the blades, the NACA 10-(3)(062)-045 propeller, had lower losses at high tip speeds, the difference amounting to about 5 percent at a helical tip Mach number of 1.10.
Date: January 1953
Creator: Solomon, William