UNT Libraries Government Documents Department - 356 Matching Results

Search Results

Results: 1 - 24 next
open access

Aerodynamic Characteristics of Four NACA Airfoil Sections Designed for Helicopter Rotor Blades

Description: "The purpose of the present work is to extend the previous investigation and to derive additional airfoil sections designed to minimize the undesirable characteristics of the previously tested airfoils. The tests of these additional airfoils were made in the Langley two-dimensional low-turbulence tunnel (LTT)" (p. 2).
Date: February 1946
Creator: Stivers, Louis S., Jr. & Rice, Fred J., Jr.
Item Type: Refine your search to only Report
open access

Aerodynamic Characteristics of Several Modifications of a 0.45-Scale Model of the Vertical Tail of the Curtiss XP-62 Airplane

Description: "In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane" (p. 1).
Date: July 1946
Creator: Lowry, John G.; Turner, Thomas R. & Liddell, Robert B.
Item Type: Refine your search to only Report
open access

Aerodynamic Data for a Wing Section of the Republic XF-12 Airplane Equipped With a Double Slotted Flap

Description: Report presenting an investigation in the two-dimensional low-turbulence tunnels for the purpose of developing an optimum flap configuration for maximum lift on an airfoil section for the Republic XF-12 airplane equipped with a double slotted flap. Lift and flap loads were obtained at several flap deflections for two flap paths. Results regarding lift, drag, and flap loads are provided.
Date: January 1946
Creator: Cahill, Jones F.
Item Type: Refine your search to only Report
open access

Aerodynamics of the carburetor air scoop and the engine cowling of a single-engine torpedo-bomber-type airplane

Description: From Introduction: "An investigation of the power-plant installation of a single-engine torpedo-bomber-type airplane has been conducted in the NACA Cleveland altitude wind tunnel at the request of the Bureau of Aeronautics, Navy Department. A similar investigation was previously conducted on a three-tenths scale mock-up of the forward portion of the fuselage of this airplane in the Langley 20-foot tunnel. (See reference 1)."
Date: June 1946
Creator: Palter, Herman
Item Type: Refine your search to only Report
open access

Air-Flow and Performance Characteristics of Engine-Stage Supercharger of a Double-Row Radial Aircraft Engine 2: Effect of Design Variables

Description: Report presenting an investigation to determine the effect of the location of the diffuser vanes with respect to the supercharger outlets and the effect of flow conditions at the impeller inlet on the air-flow distribution in the outlets of the engine-stage supercharger of an 18-cylinder double-row radial aircraft engine. The effect of flow conditions at the impeller inlet was investigated by distorting the flow at the inlet and noting the effect in the supercharger outlets. Results regarding t… more
Date: August 1946
Creator: Baas, Edmund J. & Dugan, Paul D.
Item Type: Refine your search to only Report
open access

Airscrew Gyroscopic Moments

Description: "When flying in a turn or pulling out of a dive, the airscrew exerts a gyroscopic moment on the aircraft, In the case of airscrews with three or more blades, arranged symmetrically, the value of the gyroscopic moment is J(sub x) omega(sub x) omega(sub y), where J(sub x) denotes the axial moment of inertia about the axis of rotation of the airscrew, omega(sub x) the angular upeed of the airscrew about its axis, and omega (sub Y) the rotary speed of the whole aircraft about an axis parallel to th… more
Date: September 1946
Creator: Bock, G.
Item Type: Refine your search to only Report
open access

Altitude cooling investigation of the R-2800-21 engine in the P-47G airplane 2: investigation of the engine & airplane variables affecting the cylinder temperature distribution

Description: "The data obtained from cooling tests of an R-2800-21 engine installed in a P-47G airplane were studied to determine which engine and airplane operation variables were mainly responsible for the extremely uneven temperature distribution among the 18 engine cylinders obtained at the medium and high engine-power conditions. The tests consisted of flights at altitudes from 5000 to 35,000 feet for the normal range of engine and airplane operation. The results of the study showed that a flow conditi… more
Date: October 9, 1946
Creator: Pesman, Gerard J. & Kaufman, Samuel J.
Item Type: Refine your search to only Report
open access

Altitude cooling investigation of the R-2800-21 engine in the P-47g airplane 3: individual-cylinder temperature reduction by means of intake-pipe throttle and by coolant injection

Description: "Flight tests were conducted on a R-2800-21 engine in the P-47G airplane to determine the effect on the wall temperatures of cylinder 10 of throttling the charge in the intake pipe and of injecting a water-ethanol coolant into the intake pipe. Cylinder 10 was chosen for this investigation because it runs abnormally hot (head temperatures of the order of 45 F higher than those of the next hottest cylinder) at the medium and high-power conditions. Tests with interchanged cylinders showed that the… more
Date: October 9, 1946
Creator: Bell, E. Barton; Valerino, Michael F. & Manganiello, Eugene J.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Oil-System Performance of XR-4360-8 Engine in XTB2D-1 Airplane

Description: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the aerodynamic characteristics and the oil delivery critical altitude of the oil-cooler installation of an XTB2D-1 airplane. The investigation was made with the propeller removed end with the engine operating at 1800 brake horsepower, an altitude of 15,000 feet (except for tests of oil-delivery critical altitude), oil-cooler flap deflections from -20 degrees to 20 degrees and inclinations of the thrust axis of 0… more
Date: October 11, 1946
Creator: Conrad, E. William
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loading, 1, Aeroproducts H20C-162-X11M2 Four-Blade Propeller

Description: "An investigation was made in the Cleveland Altitude wind tunnel to determine the performance of an Aeroproducts H20C-162-X11M2 four-blade propeller on a YP-47M airplane at high blade loadings and high engine powers. The propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements are indicative only of trends in propeller efficiency with changes in power coefficient and advance-di… more
Date: October 11, 1946
Creator: Saari, Martin J. & Wallner, Lewis E.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loading 2 - Curtiss 838-1C2-18R1 Four-Blade Propeller

Description: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the performance of a Curtiss propeller with four 838-1C2-1SR1 blades on a YP-47M airplane at high blade loadings and engine powers. The study was made for a range of power coefficients between 0.30 and 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio, inasmuch as … more
Date: November 26, 1946
Creator: Wallner, Lewis E. & Sorin, Solomon M.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings 4 - Curtiss 732-1C2-0 Four-Blade Propeller

Description: "An altitude-wind-tunnel investigation has been made to determine the performance of a Curtiss 732-1C2-0 four-blade propeller on a YP-47M airplane at high blade loadings and engine power. Propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and .50" (p. 1).
Date: November 26, 1946
Creator: Saari, Martin J. & Sorin, Solomon M.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings 5 - Curtiss 836-14C2-18R1 Four-Blade Propeller

Description: An investigation of the performance of several propellers on the YP-47M airplane at high blade loadings has been conducted in the Cleveland altitude wind tunnel at the request of the Air Materiel Command, Army Air Forces. As part of the program, a study was made of a Curtiss 836-14C2-18R1 four-blade propeller. The investigation was made for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.30, 0.40, and 0.50 for density altitudes from 10,000 to 45,000 feet, engine… more
Date: December 2, 1946
Creator: Saari, Martin J. & Wallner, Lewis E.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings 6 - Hamilton Standard 6507A-2 Four- and Three-Blade Propellers

Description: "An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-st… more
Date: December 19, 1946
Creator: Saari, Martin J. & Sorin, Solomon M.
Item Type: Refine your search to only Report
open access

Altitude-wind-tunnel tests of power-plant installation in jet-propelled fighter

Description: From Introduction: "The research program included clean-up tests (unpublished data) and stability and control tests (reference 1) made in the NACA Langley full-scale tunnel. An investigation of the aerodynamic characteristics of the power-plant installation in the Cleveland altitude wind tunnel is discussed in this report."
Date: February 1946
Creator: Preston, G. Merritt; Black, Fred O., Jr. & Jagger, James M.
Item Type: Refine your search to only Report
open access

Analysis of Available Data on the Effects of Tabs on Control-Surface Hinge Moments

Description: From Introduction: "A collection balanced-aileron test data is given in reference 1. Reference 2 presents a collection of data applicable to the design of tail surfaces. The results of analyses of data for control surfaces with internal balances, plain-overhang and Frise balances, beveled trailing edges, and unshielded horn balances have already been published in references 3 to 6."
Date: May 1946
Creator: Crandall, Stewart M. & Murray, Harry E.
Item Type: Refine your search to only Report
open access

Analysis of cooling limitations and effect of engine-cooling improvements on level-flight cruising performance of four-engine heavy bomber

Description: From Introduction: "The difficulties experienced in cooling the exhaust-valve seats of the rear-row cylinders have been overcome to a considerable extent by improving the mixture distribution through application of the injection impeller (reference 1) and by augmenting the flow of cooling air to the critical baffles (reference 2). Flight tests of this airplane (reference 3) indicated that the temperatures of exhaust-valve seats on rear-row cylinders were markedly lowered by these modifications … more
Date: March 14, 1946
Creator: Marble, Frank E.; Miller, Marlon A. & Bell, E. Barton
Item Type: Refine your search to only Report
open access

Analysis of Deep Rectangular Shear Web Above Buckling Load

Description: From Introduction: "An analysis of a square web above the buckling load was presented in reference 1. The analysis of reference 1 therefore was repeated for a shear web with depth/width = 2.5. Comparison of the results with those for the square web then would indicate the effect in the depth-width ratio."
Date: March 1946
Creator: Levy, Samuel; Woolley, Ruth M. & Corrick, Josephine N.
Item Type: Refine your search to only Report
open access

Analysis of Effect of Rolling Pull-Outs on Wing and Aileron Loads of a Fighter Airplane

Description: An analysis was made to determine the effect of rolling pull-out maneuvers on the wing and aileron loads of a typical fighter airplane, the P-47B. The results obtained indicate that higher loads are imposed upon wings and ailerons because of the rolling pull-out maneuver, than would be obtained by application of the loading requirements to which the airplane was designed. An increase of 102 lb or 15 percent of wing weight would be required if the wing were designed for rolling pull-out maneuver… more
Date: March 1946
Creator: Pearson, Henry A. & Aiken, William S., Jr.
Item Type: Refine your search to only Report
open access

Analysis of Jet-Propulsion-Engine Combustion-Chamber Pressure Losses

Description: From Summary: "The development and the use of a chart for estimating the pressure losses in jet-engine combustion chambers are described. By means of the chart, the pressure losses due to fluid friction and to momentum changes in the air flow accompanying combustion can be separately evaluated. The over-all pressure losses computed from the pressure-loss chart are within 7 percent of the experimental values for the three types of combustion chambers considered herein."
Date: July 31, 1946
Creator: Pinkel, I. Irving & Shames, Harold
Item Type: Refine your search to only Report
open access

Analysis of propeller efficiency losses associated with heated-air thermal de-icing

Description: From Introduction: "The results of the tests made with unheated internal flow are reported in reference 1. It is the purpose of this paper to attempt to express simply the efficiency loss as a function of the parameters which govern propeller operation and the internal air flow. The derived equations are correlated with the data presented in reference 1."
Date: July 1946
Creator: Corson, Blake W. & Maynard, Julian D.
Item Type: Refine your search to only Report
open access

Analysis of spark-ignition engine knock as seen in photographs taken at 200,000 frames per second

Description: Report discussing a motion picture of the development of knock in a spark-ignition engine, which consists of 20 photographs taken at intervals of 5 microseconds, or at a rate of 200,000 photographs per second, with an equivalent wide-open exposure time of 6.4 microseconds for each photograph.
Date: 1946~
Creator: Miller, Cearcy D.; Olsen, H. Lowell; Logan, Walter O., Jr. & Osterstrom, Gordon E.
Item Type: Refine your search to only Report
Back to Top of Screen