UNT Libraries Government Documents Department - Browse

ABOUT BROWSE FEED

The 1350 F stress-rupture properties of two wrought alloys and three cast alloys

Description: From Summary: "These properties compare favorably with those of the strongest similar alloys previously investigated. However, compared with a 60Cr-25Fe-15Mo alloy, the three cobalt-chronium-nickel cast alloys are inferior. A correlation of NACA and OSRD (Project NRC-8) data is presented, showing the variation of rupture strengths with temperature in the range of 1350^o to 2000^o for alloys."
Date: November 1947
Creator: Reynolds, E E; Freeman, J W & White, A E

Abstracts pertaining to seaplanes

Description: Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.
Date: July 24, 1947
Creator: Bidwell, Jerold M & King, Douglas A

Acceleration Characteristics of R-3350 Engine Equipped with NACA Injection Impeller

Description: Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump. The vacuum-operated accelerating pump of the hydraulic-metering carburetor was modified to produce satisfactory accelerations by supplementing the standard air chamber with an additional 75-cubic spring. The throttle-actuated accelerating pump of the direct-metering carburetor was modified to produce satisfactory accelerations by replacing the standard 0.028-inch-diameter bleed in the load-compensator balance line with a smaller bleed of 0.0225-inch diameter. The results of this investigation indicated that both carburetors can be easily modified to produce satisfactory acceleration characteristics of the engine and no definite choice between the types of carburetor and accelerating pump can be made. Use of the direct-metering carburetor, however, probably resulted in better fuel distribution to the cylinders during the acceleration period and reduced the backfire hazard because all the fuel is introduced through the injection impeller.
Date: January 8, 1947
Creator: Hickel, Robert O. & Snider, William E.

Acceleration Measurements During Landing in Rough Water of a 1/7-Scale Dynamic Model of Grumman XJR2F-1 Amphibian - Langley Tank Model 212, TED No. NACA 2378

Description: Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size). Maximum normal accelerations of about 6.5g were obtained in 4.4 inch waves and 8.5g were obtained in 8.0 inch waves. A maximum angular acceleration corresponding to 16 radians per second per second, full size, was obtained in the higher waves. The data indicate that the airplane will experience its greatest accelerations when landing in waves of about 20 feet (140 ft, full size) in length.
Date: May 6, 1947
Creator: Land, Norman S. & Zeck, Howard

Acceleration Measurements During Landings of a 1/5.5-Size Dynamic Model of the Columbia XJL-1 Amphibian in Smooth Water and in Waves: Langley Tank Model 208M, TED No. NACA 2336

Description: A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g. During landings in rough water the greatest vertical acceleration measured was 15.4g, for a landing in 6.4-foot by 165-foot waves. The impact accelerations increased with increase in wave height and, in general, decreased with increase in wave length. During the landings in waves the model bounced into the air at stalled attitudes at speeds below flying speed. The model trimmed up to the mechanical trim stop (20 deg) during landings in waves of heights greater than 2.0 feet. Solid water came over the bow and damaged the propeller during one landing in 6.4-foot waves. The vertical acceleration coefficients at first impact from the tank tests of a 1/5.5-size model were in fair agreement with data obtained at the Langley impact basin during tests of a 1/2-size model of the hull.
Date: September 25, 1947
Creator: Clement, Eugene P. & Havens, Robert F.

Accuracy of airspeed measurements and flight calibration procedures

Description: From Summary: "The sources of error that may enter into the measurement of airspeed by pitot-static methods are reviewed in detail together with methods of flight calibration of airspeed installations. Special attention is given to the problem of accurate measurements of airspeed under conditions of high speed and maneuverability required of military airplanes." (author).
Date: 1948
Creator: Huston, Wilber B

Adaptor for measuring principal strains with Tuckerman strain gage

Description: Report discussing an adapter which uses three Tuckerman optical strain gages to measure the displacement of the three vortices of an equilateral triangle along lines 120 degrees apart. These displacements are substituted in well-known equations in order to compute the magnitude and direction of the principal strains. Tests of the adaptor indicate that principal strains over a gage length of 1.42 inch may be measured with a systematic error not exceeding 4 percent and a mean observational error of the order of + or minus 0.000006. The maximum observed error in strain was of the order of 0.00006. The directions of principal strains for unidirectional stress were measured with the adaptor with an average error of the order of 1 degree.
Date: June 1943
Creator: Mcpherson, A E

Addition of heat to a compressible fluid in motion

Description: From Introduction: "The purpose of this report is to summarize, without extended proofs, the results of a study of a simplified model of nonadiabiatic, compressible fluid flow, both subsonic and supersonic, and to state these results in a form that will make them immediately useful in providing a theoretical background for current technical problems of high-speed combustion.
Date: February 1945
Creator: Hicks, Bruce L

Additional abstracts pertaining to seaplanes

Description: From Summary: "About 500 additional references pertaining to hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings:GENERAL INFORMATION, HYDROSTATICS, HYDRODYNAMICS, AERODYNAMICS, OPERATION, and RESEARCH. The compilation is an extension of NACA RM No. L6I13, entitled "Abstracts Pertaining to Seaplanes," by Jerold M. Bidwell and Douglas A. King. An author index and a subject index are included."
Date: March 9, 1948
Creator: Bidwell, J. M. & King, D. A.

Additional free-flight tests of the rolling effectiveness of several wing-spoiler arrangements at high subsonic, transonic, and supersonic speeds

Description: From Introduction: "The purpose of the present paper is to present results obtained recently relating to the characteristics of a full-span sharp-edge spoiler with an 0.02-chord projection above the wing surface at several chordwise positions and also to the relative effectiveness of the sharp-edge spoiler and a wedge-type spoiler located at the 80-percent-chord line."
Date: November 24, 1948
Creator: Strass, H Kurt

The additional-mass effect of plates as determined by experiments

Description: From Introduction: "The apparent increase in the inertia properties of a body moving in a fluid medium has been called the additional-mass effect. This report presents a resume of test procedures and results of experimental determinations of the additional-mass effect of flat plates. In addition to data obtained from various foreign sources and from a NACA investigation in 1933, the results of tests recently conducted by the National Advisory Committee for Aeronautics are included."
Date: 1941
Creator: Gracey, William

Aerodynamic and hydrodynamic tests of a family of models of flying hulls derived from a streamline body -- NACA model 84 series

Description: Report discussing a series of related forms of flying-boat hulls representing various degrees of compromise between aerodynamic and hydrodynamic requirements was tested in Langley Tank No. 1 and in the Langley 8-foot high-speed tunnel. The purpose of the investigation was to provide information regarding the penalties in water performance resulting from further aerodynamic refinement and, as a corollary, to provide information regarding the penalties in range or payload resulting from the retention of certain desirable hydrodynamic characteristics. The information should form a basis for over-all improvements in hull form.
Date: 1943?
Creator: Parkinson, John B; Olson, Roland E; Draley, Eugene C & Luoma, Arvo A

Aerodynamic characteristics and flap loads of the brake-flap installation on the 0.40-scale model of the F4F-3 left wing panel

Description: From Introduction: "The data are presented in coefficient form and include lift, drag, and pitching-moment coefficients of the airfoil-flap comoinations and the normal-force, chord-force, and hinge-moment coefficients of the upper (perforated split) flap and lower (slotted) flap."
Date: October 1942
Creator: Liddell, Robert B

Aerodynamic characteristics at high speeds of a two-blade NACA 10-(3)(062)-045 propeller and of a two-blade NACA 10-(3)(08)-045 propeller

Description: From Introduction: "The aerodynamic characteristics of a series of 10-foot-diameter propellers are being investigated in the Langley 16-foot high-speed tunnel in a comprehensive propeller research program. Using high-critical-speed NACA 16-series airfoil sections (reference 1), these propellers are designed to have Betz minimum induced-energy loss loading (reference 2) for a blade angle of 45^o at the 0.7 radius, when used as a four-blade propeller operating at an advance ratio of approximately 2.1 The ultimate purpose of the program is to determine the influence upon propeller design factors and of compressiblity; the propeller tests reported herein form part of the investigation of the effects of blade-section thickness ratio."
Date: October 1, 1948
Creator: Solomon, William