UNT Libraries Government Documents Department - Browse
Showing: 1 - 24 of 790 Results.
Results as a List of Thumbnails and Descriptive Information Results as a Grid of Images Print This Result Page Keep up to Date with an RSS feed of results matching your query.
Description: From Summary: "These properties compare favorably with those of the strongest similar alloys previously investigated. However, compared with a 60Cr-25Fe-15Mo alloy, the three cobalt-chronium-nickel cast alloys are inferior. A correlation of NACA and OSRD (Project NRC-8) data is presented, showing the variation of rupture strengths with temperature in the range of 1350^o to 2000^o for alloys."
Date: November 1947
Creator: Reynolds, E E; Freeman, J W & White, A E
Description: Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.
Date: July 24, 1947
Creator: Bidwell, Jerold M & King, Douglas A
Description: Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump. The vacuum-operated accelerating pump of the hydraulic-metering carburetor was modified to produce satisfactory accelerations by supplementing the standard air chamber with an additional 75-cubic spring. The throttle-actuated accelerating pump of the direct-metering carburetor was modified to produce satisfactory accelerations by replacing the standard 0.028-inch-diameter bleed in the load-compensator balance line with a smaller bleed of 0.0225-inch diameter. The results of this investigation indicated that both carburetors can be easily modified to produce satisfactory acceleration characteristics of the engine and no definite choice between the types of carburetor and accelerating pump can be made. Use of the direct-metering carburetor, however, probably resulted in better fuel distribution to the cylinders during the acceleration period and reduced the backfire hazard because all the fuel is introduced through the injection impeller.
Date: January 8, 1947
Creator: Hickel, Robert O. & Snider, William E.
Acceleration Measurements During Landing in Rough Water of a 1/7-Scale Dynamic Model of Grumman XJR2F-1 Amphibian - Langley Tank Model 212, TED No. NACA 2378
Description: Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size). Maximum normal accelerations of about 6.5g were obtained in 4.4 inch waves and 8.5g were obtained in 8.0 inch waves. A maximum angular acceleration corresponding to 16 radians per second per second, full size, was obtained in the higher waves. The data indicate that the airplane will experience its greatest accelerations when landing in waves of about 20 feet (140 ft, full size) in length.
Date: May 6, 1947
Creator: Land, Norman S. & Zeck, Howard
Acceleration Measurements During Landings of a 1/5.5-Size Dynamic Model of the Columbia XJL-1 Amphibian in Smooth Water and in Waves: Langley Tank Model 208M, TED No. NACA 2336
Description: A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g. During landings in rough water the greatest vertical acceleration measured was 15.4g, for a landing in 6.4-foot by 165-foot waves. The impact accelerations increased with increase in wave height and, in general, decreased with increase in wave length. During the landings in waves the model bounced into the air at stalled attitudes at speeds below flying speed. The model trimmed up to the mechanical trim stop (20 deg) during landings in waves of heights greater than 2.0 feet. Solid water came over the bow and damaged the propeller during one landing in 6.4-foot waves. The vertical acceleration coefficients at first impact from the tank tests of a 1/5.5-size model were in fair agreement with data obtained at the Langley impact basin during tests of a 1/2-size model of the hull.
Date: September 25, 1947
Creator: Clement, Eugene P. & Havens, Robert F.
Description: Tests of two 10-foot-diameter two-blade propellers which differed only in shank design have been made in the Langley 16-foot high-speed tunnel. The propellers are designated by their blade design numbers, NACA 10-(5)(08)-03, which had aerodynamically efficient airfoil shank sections, and NACA l0-(5)(08)-03R which had thick cylindrical shank sections typical of conventiona1 blades, The propellers mere tested on a 2000-horsepower dynamometer through a range of blade-angles from 20deg to 55deg at various rotational speeds and at airspeeds up to 496 miles per hour. The resultant tip speeds obtained simulate actual flight conditions, and the variation of air-stream Mach number with advance ratio is within the range of full-scale constant-speed propeller operation. Both propellers were very efficient, the maximum envelope efficiency being approximately 0,95 for the NACA 10-(5)(08)-03 propeller and about 5 percent less for the NACA 10-(5)(08)-03R propeller. Based on constant power and rotational speed, the efficiency of the NACA 10-(05)(08)-03 propeller was from 2.8 to 12 percent higher than that of the NACA 10-(5)(08)-03R propeller over a range of airspeeds from 225 to 450 miles per hour. The loss in maximum efficiency at the design blade angle for the NACA 10-(5)(08)-03 and 10-(5)(08)-03R propellers vas about 22 and 25 percent, respectively, for an increase in helical tip Mach number from 0.70 to 1.14.
Date: February 13, 1947
Creator: Maynard, Julian D.
Aerodynamic characteristics at subcritical and supercritical Mach numbers of two airfoil sections having sharp leading edges and extreme rearward positions of maximum thickness
Description: From Introduction: "A 12-percent-chord-thick wedge section and a reversed NACA 0012 section were chosen for these tests as they are representative of sections having no boat tailing and appreciable boat tailing (i.e., blunt and rounded trailing edges, respectively), and the results of this investigation are compared with those obtained from a previous investigation of the NACA 0012 section. Conclusions are drawn regarding the relative merits of the two unconventional sections and the conventional section in transonic speed range."
Date: November 6, 1947
Creator: Eggers, A J , Jr
Aerodynamic characteristics of a 42 degree swept-back wing with aspect ratio 4 and NACA 64(sub 1)-112 airfoil sections at Reynolds numbers from 1,700,000 to 9,500,000
Description: No Description Available.
Date: May 23, 1947
Creator: Neely, Robert H & Conner, D William
Aerodynamic characteristics of a 45 degree swept-back wing with aspect ratio of 3.5 and NACA 2S-50(05)-50(05) airfoil sections
Description: From Introduction: "The present paper presents the scale effect on the longitudinal aerodynamic characteristics, the aerodynamic characteristics in yaw, and the tuft studies for 0^o and 3.7^o yaw. The results of the effect of leading-edge and trailing-edge flaps on the aerodynamic characteristics of the wing will be presented in later reports."
Date: August 4, 1947
Creator: Proterra, Anthony J
Description: Theoretical pressure distributions and measured lift, drag, and pitching moment characteristics at three values of Reynolds number are presented for a group of NACA four-digit-series airfoil sections modified for high-speed applications. The effectiveness of flaps applied to these airfoils and the effect of standard leading-edge roughness were also investigated at one value of Reynolds number. Results are also presented of tests of three conventional NACA four-digit-series airfoil sections.
Date: November 14, 1947
Creator: Loftin, Laurence K., Jr. & Cohen, Kenneth G.
Aerodynamic Characteristics of a Portion of the Horizontal Tail from a Douglas C-74 Airplane with Fabric-Covered Elevators
Description: A Douglas C-74 airplane, during a test dive at about 0.525 Mach number, experienced uncontrollable longitudinal oscillations sufficient to cause shedding of the outer wing panels and the subsequent crash of the airplane. Tests of a section of the horizontal tail plane from a C-74 airplane were conducted in the Ames 16-foot high-speed wind tunnel to investigate the possibility of the tail as a contributing factor to the accident. The results of the investigations of fabric-covered elevators in various conditions of surface deformation are presented in this report.
Date: May 6, 1947
Creator: Perone, Angelo & Berthold, Cecil L.
Description: An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of three deep-stepped planing-tail flying-boat hulls differing only in the amount of step fairing. The hulls were derived by increasing the unfaired step depth of a planing-tail hull of a previous aerodynamic investigation to a depth about 92 percent of the hull beam. Tests were also made on a transverse-stepped hull with an extended afterbody for the purpose of comparison and in order to extend and verify the results of a previous investigation. The investigation indicated that the extended afterbody hull had a minimum drag coefficient about the same as a conventional hull, 0.0066, and an angle-of-attack range for minimum drag coefficient of 0.0057 which was 14 percent less than the transverse stepped hull with extended afterbody; the hulls with step fairing had up to 44 percent less minimum drag coefficient than the transverse-stepped hull, or slightly more drag than a streamlined body having approximately the same length and volume. Longitudinal and lateral instability varied little with step fairing and was about the same as a conventional hull.
Date: March 13, 1947
Creator: Riebe, John M. & Naeseth, Rodger L.
Description: No Description Available.
Date: March 11, 1947
Creator: Loving, Donald L
Air-flow behavior over the wing of an XP-51 airplane as indicated by wing-surface tufts at subcritical and supercritical speeds
Description: No Description Available.
Date: April 24, 1947
Creator: Beeler, De E
Air-Stream Surveys in the Vicinity of the Tail of a 1/8.33-Scale Powered Model of the Republic XF-12 Airplane
Description: The XF-12 airplane was designed by Republic Aviation Corporation to provide the Army Air Forces with a high performance, photo reconnaissance aircraft. A series of air-stream surveys were made n the vicinity of the empennage of a 1/8.33-scale powered model of the XF-12 airplane in the Langley 19-foot pressure tunnel. Surveys of the vortical-tail region were made through a range of yaw angles of plus or minus 20 degrees at a high and low angle of attack. The horizontal-tail surveys were made over a fairly wide range of angles of attack at zero degrees yaw. Several power and flap conditions were investigated. The results are presented in the form a dynamic pressure ratios, sidewash angles, and downwash angles plotted against vertical distance from the fuselage center line. The results of the investigation indicate that a vertical tail located in a conventional position would be in a field of flow where the dynamic pressure ratios at the horizontal tail to be increased; for equal lift coefficients, the effect of power or flap deflection on the direction of flow at any particular point in the region of the horizontal tail is small.
Date: April 8, 1947
Creator: Foster, Gerald V.
Description: The forces and moments on a two-dimensional airfoil executing harmonic motions in a pulsating stream are derived on the basis of non-stationary incompressible potential flow theory, with the inclusion of the effect of the continuous sheet of vortices shed from the trailing edge. An assumption as to the form of the wake is made with a certain degree of approximation. A comparison with previous work applicable only to the special case of a stationary airfoil is made by means of a numerical example, and the excellent agreement obtained shows that the wake approximation is quite sufficient. The results obtained are expected to be useful in considerations of forced vibrations and flutter of rotary wing aircraft.
Date: June 1, 1947
Creator: Greenberg, J Mayo
Altitude Cooling Investigation of the R-2800-21 Engine in the P-47G Airplane. IV - Engine Cooling-Air Pressure Distribution
Description: A study of the data obtained in a flight investigation of an R-2800-21 engine in a P-47G airplane was made to determine the effect of the flight variables on the engine cooling-air pressure distribution. The investigation consisted of level flights at altitudes from 5000 to 35,000 feet for the normal range of engine and airplane operation. The data showed that the average engine front pressures ranged from 0.73 to 0.82 of the impact pressure (velocity head). The average engine rear pressures ranged from 0.50 to 0.55 of the impact pressure for closed cowl flaps and from 0.10 to 0.20 for full-open cowl flaps. In general, the highest front pressures were obtained at the bottom of the engine. The rear pressures for the rear-row cylinders were .lower and the pressure drops correspondingly higher than for the front-row cylinders. The rear-pressure distribution was materially affected by cowl-flap position in that the differences between the rear pressures of the front-row and rear-row cylinders markedly increased as the cowl flaps were opened. For full-open cowl flaps, the pressure drops across the rear-row cylinders were in the order of 0.2 of the impact pressure greater than across the front-row cylinders. Propeller speed and altitude had little effect on the -coolingair pressure distribution, Increase in angle of inclination of the thrust axis decreased the front ?pressures for the cylinders at the top of the engine and increased them for the cylinders at the bottom of the engine. As more auxiliary air was taken from the engine cowling, the front pressures and, to a lesser extent, the rear pressures for the cylinders at the bottom of the engine decreased. No correlation existed between the cooling-air pressure-drop distribution and the cylinder-temperature distribution.
Date: January 7, 1947
Creator: Kaufman, Samuel J.; Staudt, Robert C. & Valerino, Michael F.
Altitude-Wind-Tunnel Investigation of R-4360-18 Power-Plant Installation for XR60 Airplane, 3, Performance of Induction and Exhaust Systems
Description: A study has been made of the performance of the induction and the exhaust systems on the XR60 power-plant installation as part of an investigation conducted in the Cleveland altitude wind tunnel. Altitude flight conditions from 5000 to 30,000 feet were simulated for a range of engine powers from 750 to 3000 brake horsepower. Slipstream rotation prevented normal pressure recoveries in the right side of the main duct in the region of the right intercooler cooling-air duct inlet. Total-pressure losses in the charge-air flow between the turbosupercharger and the intercoolers were as high as 2.1 inches of mercury. The total-pressure distribution of the charge air at the intercooler inlets was irregular and varied as much as 1.0 inch of mercury from the average value at extreme conditions, Total-pressure surveys at the carburetor top deck showed a variation from the average value of 0.3 inch of mercury at take-off power and 0.05 inch of mercury at maximum cruising power, The carburetor preheater system increased the temperature of the engine charge air a maximum of about 82 F at an average cowl-inlet air temperature of 9 F, a pressure altitude of 5000 feet, and a brake horsepower of 1240.
Date: March 26, 1947
Creator: Dupree, David T. & Hawkins, W. Kent
Altitude-Wind-Tunnel Investigation of the 19B-2, 19B-8 and 19XB-1 Jet- Propulsion Engines, 4, Analysis of Compressor Performance
Description: Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers. At each simulated flight condition the engine was run over its full operable range of speeds. Performance characteristics of the 19B-8 and 19XB-1 compressors for the range of operation obtainable in the turboJet-engine installation are presented. Compressor characteristics are presented as functions of air flow corrected to sea-level conditions, compressor Mach number, and compressor load coefficient. For the range of compressor operation investigated, changes in Reynolds number had no measurable effect on the relations among compressor Mach number, corrected air flow, compressor load coefficient, compressor pressure ratio, and compressor efficiency. The operating lines for the 19B-8 compressor lay on the low-air-flow side of the region of maximum compressor efficiency; the 19B-8 compressor operated at higher average pressure coefficients per stage and produced a lower over-all pressure ratio than did the 19XB-1 compressor.
Date: April 4, 1947
Creator: Dietz, Robert O. & Kuenzig, John K.
Filter: CollectionsThis dialog allows you to filter your current search. Each of the Collections listed note their name and the number of records that will be limited down to if you choose that option.
Filter: Serial/Series TitlesThis dialog allows you to filter your current search. Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option. The list can be sorted by name or the count.
Having trouble finding an option within the list of Serial/Series Titles? Start typing and we'll update the list to show only those items that match your needs. Try limiting with other filters first or use this comprehensive list of titles as an alternative starting point.
NACA Research Memorandums 323 323 NACA Technical Notes 304 304 NACA Technical Memorandums 79 79 NACA Technical Reports 29 29 Atomic Energy Commission Reports 25 25 United States Bureau of Mines Reports 21 21 Report of investigations (United States. Bureau of Mines) 14 14 Information circular (United States. Bureau of Mines) 3 3 North American Fauna 2 2 Technical note (United States. National Advisory Committee for Aeronautics) 2 2 Technical paper (United States. Bureau of Mines) 2 2 United States Fish and Wildlife Service Reports 2 2 Annual Report of Research and Technologic Work on Coal 1 1 Brookhaven National Laboratory Reports 1 1 Bulletin (Geological Survey (U.S.)) 1 1 Coast and Geodetic Survey Reports 1 1 Geologic Investigations in the American Republics 1 1 MDDC (Series) 1 1 Miscellaneous publications (United States. Bureau of Standards) 1 1 NACA Advanced Restricted Reports 1 1 NACA Wartime Reports 1 1 NBS special publication 1 1 National Bureau of Standards Reports 1 1 National Motor-Gasoline Survey 1 1 Report (U.S. Atomic Energy Commission) 1 1 Report of the National Conference on Weights and Measures 1 1 U.S. Waterways Experiment Station Reports 1 1 United States Earthquakes 1 1 United States Geological Survey Reports 1 1
Filter: U.S. StatesThis dialog allows you to filter your current search. Each of the U.S. States listed note their name and the number of records that will be limited down to if you choose that option. The list can be sorted by name or the count.
Having trouble finding an option within the list of U.S. States? Start typing and we'll update the list to show only those items that match your needs.
Filter: CountiesThis dialog allows you to filter your current search. Each of the Counties listed note their name and the number of records that will be limited down to if you choose that option. The list can be sorted by name or the count.
Filter: MonthsThis dialog allows you to filter your current search. Each of the Months listed note their name and the number of records that will be limited down to if you choose that option. The list can be sorted by name or the count.
Filter: DaysThis dialog allows you to filter your current search. Each of the Days listed note their name and the number of records that will be limited down to if you choose that option. The list can be sorted by name or the count.
Having trouble finding an option within the list of Days? Start typing and we'll update the list to show only those items that match your needs.
1st 428 428 2nd 4 4 3rd 10 10 4th 12 12 5th 9 9 6th 15 15 7th 9 9 8th 9 9 9th 10 10 10th 18 18 11th 19 19 12th 10 10 13th 14 14 14th 12 12 15th 8 8 16th 9 9 17th 8 8 18th 9 9 19th 10 10 20th 11 11 21st 8 8 22nd 12 12 23rd 6 6 24th 12 12 25th 11 11 26th 9 9 27th 5 5 28th 10 10 29th 12 12 30th 7 7 31st 4 4