UNT Libraries Government Documents Department - 650 Matching Results

Search Results

D-0 North End Cap Calorimeter Cold Test Results

Description: The North endcap calorimeter vessel was recieved on July 1, 1990. A cooldown of the pressure vessel with liquid nitrogen was performed on July 10-11 to check the vessel's integrity. With the pressure vessel cold, the insulating vacuum was monitored for leaks. Through out the testing, the insulating vacuum remained good and the vessel passed the test. The cold test was carried out per the procedures of D-Zero engineering note 3740.220-EN-250. The test was very similar to the cold test performed on the Central Calorimeter in October of 1987. Reference D-Zero engineering notes 3740.210-EN-122, 3740.000-EN107, and 3740.210-EN-110 for information about the CC cold test. The insulating vacuum space was pumped on while equipment was being connected to the pressure vessel. Two hours after starting to pump with the blower the vacuum space pressure was at about 210 microns. Pumping on the vacuum space for the next 15 hours showed no progress and a leak detector was connected to the pumping line. A leak check showed a leak in a thermocouple feedthru on the vacuum space relief plate. After fixing the leak, the pressure dropped to 16 microns in less than one hour. A rate of rise test was performed starting at a pressure of 13 microns. The pressure rose to 39 microns within 8 minutes and then only rose to 43 microns in 2.5 hours (1.6 microns/hour). After all connections were made to the pressure vessel, a vacuum pump with an estimated effective pumping speed of about 70 scfm was valved on. The lowest pressure achieved after 2 days of pumping was 80 microns. Valving out the pump for 30 minutes resulted in a 5 micron per minute rate of rise. The rate of rise was considered acceptable since there were known leak paths through the bolts of the signal ...
Date: August 2, 1990
Creator: Michael, J.

D-0 South End Cap Calorimeter Cold Test Results

Description: The South endcap calorimeter vessel was moved into Lab A on Sept. 18, 1990. A cooldown of the pressure vessel with liquid nitrogen was performed on Sept. 26 to check the vessel's integrity. With the pressure vessel cold, the insulating vacuum was monitored for leaks. Through out the testing, the insulating vacuum remained good and the vessel passed the test. The cold test was carried out per the procedures of D-Zero engineering note 3740.220-EN-250. The test was very similar to the cold test performed on the Central Calorimeter in October of 1987. The test of the ECS was performed in the same manner using the same equipment as the ECN cold test. Reference D-Zero engineering notes 3740.210-EN-122, 3740.000-EN-I07, and 3740.210-EN-II0 for information about the CC cold test. Reference EN-260 for the results of the ECN cold test. The insulating vacuum space was pumped on while equipment was being connected to the pressure vessel. Two hours after starting to pump with the blower the vacuum space pressure was at about 40 microns. The pumping continued overnight (another 16 hours). In the morning the pressure was 11.5 microns. A rate of rise test was performed. With the pump valved off, the pressure rose to 14 microns within 5 minutes and then rose to 16 microns in 6 hours (0.33 microns/hour). After all connections were made to the pressure vessel, a vacuum pump with an estimated effective pumping speed of about 70 scfm was valved on. After 18 hours, the pressure vessel was down to 270 microns. An additional day of pumping took the pressure down to only 250 microns. A leak was then found and fixed around the seal of the rupture disc. The pump was put on line again. The pressure vessel with pump on line was 27 microns after 16.5 ...
Date: November 26, 1990
Creator: Rucinski, R.

3-D computer simulations of EM fields in the APS vacuum chamber: Part 1, Frequency-domain analysis

Description: The vacuum chamber proposed for the storage ring of the 7-GeV Advanced Photon Source (APS) basically consists of two parts: the beam chamber and the antechamber, connected to each other by a narrow gap. A sector of 1-meter-long chamber with dosed end plates, to which are attached the 1-inch-diameter beampipes centered at the beam chamber, has been built for experimental purposes. The 3-D code MAFIA has been used to simulate the frequency-domain behaviors of EM fields in this setup. The results are summarized in this note and are compared with that previously obtained from 2-D simulations and that from network analyzer measurements. They are in general agreement. A parallel analysis in the time-domain is reported in a separate note. The method of our simulations can be briefly described as follows. The 1-inch diameter beampipes are terminated by conducting walls at a length of 2 cm. The whole geometry can thus be considered as a cavity. The lowest RF modes of this geometry are computed using MAFIA. The eigenfrequencies of these modes are a direct output of the eigenvalue solver E3, whereas the type of each mode is determined by employing the postprocessor P3. The mesh sizes are chosen such that they are small enough for computations in the frequency region in which we are interested (the sampling theorem), while the total number of mesh points is still well within the range that our computer system can cope with.
Date: September 4, 1990
Creator: Chou, W. & Bridges, J.

1989 OCRWM [Office of Civilian Radioactive Waste Management] Bulletin compilation and index

Description: The OCRWM Bulletin is published by the Department of Energy, Office of Civilian Radioactive Waste Management to provide current information about the national program for managing spent fuel and high-level radioactive waste. This document is a compilation of issues from the 1989 calendar year. A table of contents and one index have been provided to assist in finding information contained in this year`s Bulletins. The pages have been numbered consecutively at the bottom for easy reference. 7 figs.
Date: February 1990

1990 Fischer Standard study

Description: The purpose of this work is to develop a set of Titanium areal density standards for calibration and maintenance of the Fischer`s X-ray Fluorescence measurement system characterization curve program. The electron microprobe was calibrated for Titanium films on ceramic substrates using an existing set of laboratory standards (Quantity: 6 Range: 0.310 to 1.605). Fourteen source assemblies were measured and assigned values. These values are based on a mean calculation, of five separate readings, from best curve fit equations developed form the plot of the laboratory standards areal density (Source Measure) versus electron microprobe measurement (reading). The best fit equations were determined using the SAS General Linear Modeling (GLM) procedure. Four separate best fit equations were evaluated (Linear, Quadratic, Cubic and Exponential). Areal density values for the Fischer Standards appear here ordered by best fit equation based on maximum R{sup 2}.
Date: September 12, 1990
Creator: Roubik, G.J.

31st Annual Report

Description: The ACIR Library is composed of publications that study the interactions between different levels of government. This document is an annual report.
Date: January 1990
Creator: United States. Advisory Commission on Intergovernmental Relations.

Acceleration of compact toruses and fusion applications

Description: The Compact Torus (Spheromak-type) is a near ideal plasma confinement configuration for acceleration. The fields are mostly generated by internal plasma currents, plasma confinement is toroidal, and the compact torus exhibits resiliency and stability in virtue of the ``rugged`` helicity invariant. Based on these considerations we are developing a coaxial rail-gun type Compact Torus Accelerator (CTA). In the CTA, the CT ring is formed between coaxial electrodes using a magnetized Marshall gun, it is quasistatically ``precompressed`` in a conical electrode section for inductive energy storage, it is accelerated in a straight-coaxial electrode section as in a conventional rail-gun, and it is focused to small size and high energy and power density in a final ``focus`` cone section. The dynamics of slow precompression and acceleration have been demonstrated experimentally in the RACE device with results in good agreement with 2-D MHD code calculations. CT plasma rings with 100 {micro}gms mass have been accelerated to 40 Kj kinetic energy at 20% efficiency with final velocity = 1 X 10{sup 8} cm/s (= 5 KeV/H{sup +}). Preliminary focus tests exhibi dynamics of radius compression, deceleration, and bouncing. Compression ratios of 2-3 have been achieved. A scaled-up 10-100 MJ CTA is predicted to achieve a focus radius of several cm to deliver = 30 MJ ring kinetic energy in 5-10 nsec. This is sufficient energy, power, and power density to enable the CTA to act as a high efficiency, low cost ICF driver. Alternatively, the focused CT can form the basis for an magnetically insulated, inertial confinement fusion (MICF) system. Preliminary calculations of these fusion systems will be discussed.
Date: October 11, 1990
Creator: Hartman, C.W.; Eddleman, J.L.; Hammer, J.H.; Logan, B.G.; McLean, H.S. & Molvik, A.W.

Activities and Operations of the Advanced Computing Research Facility : January 1989-January 1990

Description: This report reviews the activities and operations of the Advanced Computing Research Facility (ACRF) for the period January 1, 1989, through January 31, 1990. The ACRF is operated by the Mathematics and Computer Science Division at Argonne National Laboratory. The facility's principal objective is to foster research in parallel computing. Toward this objective, the ACRF continues to operate experimental advanced computers and to sponsor new technology transfer efforts and new research projects.
Date: February 1990
Creator: Pieper, Gail W.

The Advanced Light Source at the Lawrence Berkeley Laboratory (ALS, LBL)

Description: The Advanced Light Source (ALS), a national facility currently under construction at the Lawrence Berkeley Laboratory (LBL), is a third-generation synchrotron light source designed to produce extremely bright beams of synchrotron radiation, in the energy range from a few eV to 10 keV. The design is based on a 1-1.9 GeV electron storage ring (optimized at 1.5 GeV), and utilizes special magnets, known as undulators and wigglers (collectively referred to as insertion devices), to generate the radiation. In this paper we describe the main accelerator components of the ALS, the variety of insertion devices, the radiation spectra expected from these devices, and the complement of experiments that have been approved for initial operation, starting in April 1993.
Date: August 1, 1990
Creator: Jackson, A.

Affordable Spacecraft: Design and Launch Alternatives

Description: This background paper examines several proposals for reducing the costs of spacecraft and other payloads and describes launch systems for implementing them. It is one of a series of products of a broad assessment of space transportation technologies undertaken by OTA at the request of the Senate Committee on Commerce, Science, and Transportation, and the House Committee on Science, Space, and Technology.
Date: January 1990
Creator: United States. Congress. Office of Technology Assessment.

Agricultural Research and Technology Transfer Policies for the 1990s: a special report of OTA's assessment on emerging agricultural technology: issues for the 1990s

Description: This report addresses the central issues in the debate of the 1990 Farm Bill. It was requested as part of a larger study examining emerging agricultural technologies and related issues for the 1990s by the Senate Committee on Agriculture, Nutrition, and Forestry and the House Committee on Agriculture.
Date: March 1990
Creator: United States. Congress. Office of Technology Assessment.

Los Alamos National Laboratory corregated metal pipe saw facility preliminary safety analysis report. Volume I

Description: This Preliminary Safety Analysis Report addresses site assessment, facility design and construction, and design operation of the processing systems in the Corrugated Metal Pipe Saw Facility with respect to normal and abnormal conditions. Potential hazards are identified, credible accidents relative to the operation of the facility and the process systems are analyzed, and the consequences of postulated accidents are presented. The risk associated with normal operations, abnormal operations, and natural phenomena are analyzed. The accident analysis presented shows that the impact of the facility will be acceptable for all foreseeable normal and abnormal conditions of operation. Specifically, under normal conditions the facility will have impacts within the limits posted by applicable DOE guidelines, and in accident conditions the facility will similarly meet or exceed the requirements of all applicable standards. 16 figs., 6 tabs.
Date: September 19, 1990

Alaskan Water for California?: The Subsea Pipeline Option

Description: This background paper focuses on one technological option for increasing the supply of fresh water to the Southwest-that of building a freshwater subsea pipeline to transport water from Alaska to California. Originally a suggestion by Governor Walter Hickel of Alaska, the proposal has recently attracted attention in southern California.
Date: January 1990
Creator: United States. Congress. Office of Technology Assessment.

Alternative configurations for the waste-handling building at the Yucca Mountain Repository

Description: Two alternative configurations of the waste-handling building have been developed for the proposed nuclear waste repository in tuff at Yucca Mountain, Nevada. One configuration is based on criteria and assumptions used in Case 2 (no monitored retrievable storage facility, no consolidation), and the other configuration is based on criteria and assumptions used in Case 5 (consolidation at the monitored retrievable storage facility) of the Monitored Retrievable Storage System Study for the Repository. Desirable waste-handling design concepts have been selected and are included in these configurations. For each configuration, general arrangement drawings, plot plans, block flow diagrams, and timeline diagrams are prepared.
Date: August 1990

Analysis of a third-order sum resonance

Description: It is worth considering an experiment on a sum resonance. I will give an analytic treatment of a third-order sum resonance. The treatment parallels that in LS-132 for the Walkinshaw difference resonance. Although the algebra is essentially the same as for the difference resonance, the sum resonance appears to have a richer structure.
Date: June 28, 1990
Creator: Symon, K.

Analysis of heat and mass transport processes near an emplaced nuclear waste canister; Final report

Description: A review has been performed of the models and experimental plans for evaluation of the spent fuel canister environment in a nuclear repository, e.g., the planned Yucca Mountain facilities. Special emphasis was placed on the relevance of the models and experiments to the 100 to 10,000 year prediction. The question was addressed whether one could justify testing in materials other than Yucca Mountain rock and obtain results in a relatively short time which would be relevant to the long time in Yucca Mountain. The paper discusses steam evolution in calculations and experiments, fracture models, possible measurements of relative permeability, and long time scale effects. 5 figs. (MB)
Date: May 22, 1990
Creator: Keller, C.

An analysis of repository waste-handling operations

Description: This report has been prepared to document the operational analysis of waste-handling facilities at a geologic repository for high-level nuclear waste. The site currently under investigation for the geologic repository is located at Yucca Mountain, Nye County, Nevada. The repository waste-handling operations have been identified and analyzed for the year 2011, a steady-state year during which the repository receives spent nuclear fuel containing the equivalent of 3000 metric tons of uranium (MTU) and defense high-level waste containing the equivalent of 400 MTU. As a result of this analysis, it has been determined that the waste-handling facilities are adequate to receive, prepare, store, and emplace the projected quantity of waste on an annual basis. In addition, several areas have been identified where additional work is required. The recommendations for future work have been divided into three categories: items that affect the total waste management system, operations within the repository boundary, and the methodology used to perform operational analyses for repository designs. 7 refs., 48 figs., 11 tabs.
Date: September 1, 1990
Creator: Dennis, A.W.

Analysis of solute transport in an intermediate-scale unsaturated flow experiment

Description: Radioactive waste disposal in the unsaturated zone and its subsequent migration and decay calls for prediction with the aid of transport models. Usually, such models consist of a system of partial differential equations for the concentration C (function of space and time) that has to be solved with appropriate initial and boundary conditions. These equations are based on physical first principles, but contain a number of parameters that have to be determined experimentally. Hence, experiments are crucial for validating the equations and their solution and for determining parameter values. The Los Alamos National Laboratory (LANL) has initiated and performed a series of experiments at an intermediate scale, in caissons much larger than laboratory columns, of depth comparable with natural soil, but of limited horizontal extent. These experiments were conducted with both nonreactive and reactive solutes, and are described in a series of reports. Their main advantage is in expanding the scale on one hand, while permitting careful control and measurements on the other. 8 refs., 2 figs.
Date: October 1, 1990
Creator: Dagan, G.; Springer, E. & Nguyen, V.

Annual Technical Report

Description: Highlights of the Chemical Technology (CMT) Division's activities during 1989 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including high-performance batteries (mainly lithium/iron sulfide and sodium/metal chloride), aqueous batteries (lead-acid and nickel/iron), and advanced fuel cells with molten carbonate and solid oxide electrolytes; (2) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (3) method, for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing 99Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor (the Integral Fast Reactor), and waste management; and (5) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems.
Date: March 1990
Creator: Argonne National Laboratory. Chemical Technology Division.

Anthracite R&D needs - CRADA 89-001. Final report

Description: The purpose of this research is to foster the development of one or more high performance, anthracite-fired boiler systems suitable for meeting space heating and hot water requirements of large buildings. The boiler system research would include fuel handling, combustion and heat transfer, ash handling, and control systems.
Date: September 1, 1990
Creator: Bartis, J.T. & Inberman, A.K.