UNT Libraries Government Documents Department - 37 Matching Results

Search Results

Aerodynamic characteristics of a large number of airfoils tested in the variable-density wind tunnel

Description: From Summary: "The aerodynamic characteristics of a large number of miscellaneous airfoils tested in the variable-density tunnel have been reduced to a comparable form and are published in this report for convenient reference. Plots of the standard characteristics are given in tabular form. Included is a tabulation of important characteristics for the related airfoils reported in NACA report 460. This report, in conjunction with NACA report 610, makes available in comparable and convenient form the aerodynamic data for airfoils tested in the variable-density tunnel since January 1, 1931."
Date: 1938
Creator: Pinkerton, Robert M & Greenberg, Harry

The aerodynamic characteristics of four full-scale propellers having different plan forms

Description: From Introduction: "Its main purpose is to present propeller data for four full-scale propellers of Navy design, three of which have somewhat unusual plan forms and the other one has a normal (usual present-day type) plan form. These data may give some clue as to what may be expected from fundamental changes in blade plan form."
Date: 1938~
Creator: Hartman, Edwin P & Biermann, David

The aerodynamic characteristics of full-scale propellers having 2, 3, and 4 blades of Clark y and R.A.F. 6 airfoil sections

Description: Aerodynamic tests were made of seven full-scale 10-foot-diameter propellers of recent design comprising three groups. The first group was composed of three propellers having Clark y airfoil sections and the second group was composed of three propellers having R.A.F. 6 airfoil sections, the propellers of each group having 2, 3, and 4 blades. The third group was composed of two propellers, the 2-blade propeller taken from the second group and another propeller having the same airfoil section and number of blades but with the width and thickness 50 percent greater. The tests of these propellers reveal the effect of changes in solidity resulting either from increasing the number of blades or from increasing the blade width propeller design charts and methods of computing propeller thrust are included.
Date: 1938
Creator: Hartman, Edwin P & Biermann, David

Air flow in the boundary layer of an elliptic cylinder

Description: From Introduction: "The present investigation was carried out for the purpose of supplementing the earlier work with information on the boundary layer under such conditions of air speed and turbulence that transition occurs and the layer is partly laminar and partly turbulent. In the work reported in reference 1, the air speed was about 12 feet per second, and it was assumed that the boundary layer remained in the laminar condition until after separation because the separation point remained fixed and the pressure distribution about the cylinder was unaffected until an air speed of 15 feet per second was reached."
Date: August 6, 1938
Creator: Schubauer, G B

Airfoil section characteristics as applied to the prediction of air forces and their distribution on wings

Description: From Introduction: "The system presented herein yields, within the limitations of our present knowledge of aerodynamics, a general solution of the resultant wing forces and moments and their distribution. For the sake of completeness and facility in use, the report contains a table of the important section parameters for many commonly used sections and all other necessary data required to solve the most practical design problems coming within the scope of the system."
Date: 1938
Creator: Jacobs, Eastman N. & Rhode, R. V.

Approximate stress analysis of multistringer beams with shear deformation of the flanges

Description: The problem of the skin-stringer combinations used as axially loaded panels or as covers for box beams is considered from the point of view of the practical stress analyst. By a simple substitution the problem is reduced to the problem of the single-stringer structure, which has been treated in NACA Report no. 608. The method of making this substitution is essentially empirical; in order to justify it, comparisons are shown between calculations and strain-gage tests of three beams tested by the author and of one compression panel and three beams tested and reported elsewhere.
Date: January 1, 1938
Creator: Kuhn, Paul

Calculation of the chordwise load distribution over airfoil sections with plain, split, or serially hinged trailing-edge flaps

Description: A method is presented for the rapid calculation of the incremental chordwise normal-force distribution over an airfoil section due to the deflection of a plain flap or tab, a split flap, or a serially hinged flap. This report is intended as a supplement to NACA Report no. 631, wherein a method is presented for the calculation of the chordwise normal-force distribution over an airfoil without a flap or, as it may be considered, an airfoil with flap (or flaps) neutral. The method enables the determination of the form and magnitude of the incremental normal-force distribution to be made for an airfoil-flap combination for which the section characteristics have been determined. A method is included for the calculation of the flap normal-force and hinge-moment coefficients without necessitating a determination of the normal-force distribution.
Date: January 1, 1938
Creator: Allen, H Julian

Column strength of tubes elastically restrained against rotation at the ends

Description: Report presents the results of a study made of the effects of known end restraint on commercially available round and streamline tubing of chromium-molybdenum steel, duralumin, stainless steel, and heat-treated chromium-molybdenum steel; and a more accurate method than any previously available, but still a practical method, was developed for designing compression members in riveted or welded structures, particularly aircraft. Two hundred specimens were tested as short, medium-length, and long columns with freely supported ends or elastically restrained ends. Tensile and compressive tests were made on each piece of original tubing from which column specimens were cut.
Date: January 1, 1938
Creator: Osgood, William R

Comparative flight and full-scale wind-tunnel measurements of the maximum lift of an airplane

Description: Determinations of the power-off maximum lift of a Fairchild 22 airplane were made in the NACA full-scale wind tunnel and in flight. The results from the two types of test were in satisfactory agreement. It was found that, when the airplane was rotated positively in pitch through the angle of stall at rates of the order of 0.1 degree per second, the maximum lift coefficient was considerably higher than that obtained in the standard tests, in which the forces are measured with the angles of attack fixed. Scale effect on the maximum lift coefficient was also investigated.
Date: January 1, 1938
Creator: Silverstein, Abe; Katzoff, S & Hootman, James A

Compressible flow about symmetrical Joukowski profiles

Description: The method of Poggi is employed for the determination of the effects of compressibility upon the flow past an obstacle. A general expression for the velocity increment due to compressibility is obtained. The general result holds whatever the shape of the obstacle; but, in order to obtain the complete solution, it is necessary to know a certain Fourier expansion of the square of the velocity of flow past the obstacle. An application is made to the case flow of a symmetrical Joukowski profile with a sharp trailing edge, fixed in a stream of an arbitrary angle of attack and with the circulation determined by the Kutta condition. The results are obtained in a closed form and are exact insofar as the second approximation to the compressible flow is concerned, the first approximation being the result for the corresponding incompressible flow. Formulas for lift and moment analogous to the Blasius formulas in incompressible flow are developed and are applied to thin symmetrical Joukowski profiles for small angles of attack.
Date: January 1, 1938
Creator: Kaplan, Carl

The crinkling strength and the bending strength of round aircraft tubing

Description: The upper limit of the column strength of structural members composed of thin material is the maximum axial stress such members can carry when short enough to fail locally, by crinkling. This stress is a function of the mechanical properties of the material and of the geometrical shape of the cross section. The bending strength, as measured by the modulus of rupture, of structural members is also a function of these same variables. Tests were made of round tubes of chromium-molybdenum steel and of duralumin to determine the crinkling strengths and the bending strengths in terms of the specified yield strength and the ratio of diameter to thickness. Empirical formulas are given relating these quantities.
Date: January 1, 1938
Creator: Osgood, William R

Determination of boundary-layer transition on three symmetrical airfoils in the NACA full-scale wind tunnel

Description: For the purpose of studying the transition from laminar to turbulent flow, boundary-layer measurements were made in the NACA full-scale wind tunnel on three symmetrical airfoils of NACA 0009, 0012, and 0018 sections. The effects of variations in lift coefficient, Reynolds number, and airfoil thickness on transition were investigated. Air speed in the boundary layer was measured by total-head tubes and by hot wires; a comparison of transition as indicated by the two techniques was obtained. The results indicate no unique value of Reynolds number for the transition, whether the Reynolds number is based upon the distance along the chord or upon the thickness of the boundary layer at the transition point. In general, the transition is not abrupt and occurs in a region that varies in length as a function of the test conditions.
Date: January 1, 1938
Creator: Silverstein, Abe & Becker, John V

A discussion of certain problems connected with the design of hulls of flying boats and the use of general test data

Description: Report presents the results of a survey of problems encountered in applying general test data to the design of flying-boat hulls. It is shown how basic design features may be readily determined from special plots of test data. A study of the effect of the size of a flying boat on the probable limits to be covered by the general test data is included and recommendations for special tests and new methods of presenting test data for direct use in design are given.
Date: January 1, 1938
Creator: Diehl, Walter S

Drag of cylinders of simple shapes

Description: In order to determine the effect of shape, compressibility, and Reynolds number on the drag and critical speed for simple forms, the drag forces on models of various simple geometric cross sections were measured in the NACA 11-inch high-speed wind tunnel. The models were circular, semitubular, elliptical, square, and triangular (isosceles) cylinders. They were tested over a speed range from 5 percent of the speed of sound to a value in excess of the critical speed, corresponding, for each model, approximately to a tenfold Reynolds number range, which extended from a minimum of 840 for the smallest model to a maximum of 310,000 for the largest model.
Date: January 1, 1938
Creator: Lindsey, W F

The effect of compressibility on eight full-scale propellers operating in the take-off and climbing range

Description: Tests were made of eight full-scale propellers of different shape at various tip speeds up to about 1,000 feet per second. The range of blade-angle settings investigated was from 10 degrees to 30 degrees at the 0.75 radius. The results indicate that a loss in propulsive efficiency occurred at tip speeds from 0.5 to 0.7 the velocity of sound for the take-off and climbing conditions. As the tip speed increased beyond these critical values, the loss rapidly increased and amounted, in some instances, to more than 20 percent of the thrust power for tip-speed values of 0.8 the speed of sound. In general, as the blade-angle setting was increased, the loss started to occur at lower tip speeds. The maximum loss for a given tip speed occurred at a blade-angle setting of about 20 degrees for the take-off and 25 degrees for the climbing condition. A simplified method for correcting propellers for the effect of compressibility is given in an appendix.
Date: January 1, 1938
Creator: Biermann, David & Hartman, Edwin P

The experimental and calculated characteristics of 22 tapered wings

Description: The experimental and calculated aerodynamic characteristics of 22 tapered wings are compared, using tests made in the variable-density wind tunnel. The wings had aspect ratios from 6 to 12 and taper ratios from 1:6:1 and 5:1. The compared characteristics are the pitching moment, the aerodynamic-center position, the lift-curve slope, the maximum lift coefficient, and the curves of drag. The method of obtaining the calculated values is based on the use of wing theory and experimentally determined airfoil section data. In general, the experimental and calculated characteristics are in sufficiently good agreement that the method may be applied to many problems of airplane design.
Date: January 1, 1938
Creator: Anderson, Raymond F

A flight comparison of conventional ailerons on a rectangular wing and of conventional and floating wing-tip ailerons on a tapered wing

Description: Report presents the results of flight tests comparing the relative effectiveness of conventional ailerons of the same size on wings of rectangular and tapered plan forms made with a Fairchild 22 airplane. Information is included comparing conventional and floating wing-tip ailerons on a tapered wing. The results showed that the conventional ailerons were somewhat more effective on the tapered than on the rectangular wing. The difference, however, was so small as to be imperceptible to the pilots. The floating wing-tip ailerons were only half as effective as the conventional ailerons and, for this reason, were considered unsatisfactory.
Date: January 1, 1938
Creator: Soule, H A & Gracey, W

Heat-transfer processes in air-cooled engine cylinders

Description: From a consideration of heat-transfer theory, semi-empirical expressions are set up for the transfer of heat from the combustion gases to the cylinder of an air-cooled engine and from the cylinder to the cooling air. Simple equations for the average head and barrel temperatures as functions of the important engine and cooling variables are obtained from these expressions. The expressions involve a few empirical constants, which may be readily determined from engine tests. Numerical values for these constants were obtained from single-cylinder engine tests for cylinders of the Pratt & Whitney 1535 and 1340-h engines. The equations provide a means of calculating the effect of the various engine and cooling variables on the cylinder temperatures and also of correlating the results of engine cooling tests. An example is given of the application of the equations to the correlation of cooling-test data obtained in flight.
Date: January 1, 1938
Creator: Pinkel, Benjamin

Heat transfer to fuel sprays injected into heated gases

Description: This report presents the results of a study made of the influence of several variables on the pressure decrease accompanying injection of a relatively cool liquid into a heated compressed gas. Indirectly, this pressure decrease and the time rate of change of it are indicative of the total heat transferred as well as the rate of heat transfer between the gas and the injected liquid. Air, nitrogen, and carbon dioxide were used as ambient gases; diesel fuel and benzene were the injected liquids. The gas densities and gas-fuel ratios covered approximately the range used in compression-ignition engines. The gas temperatures ranged from 150 degrees c. to 350 degrees c.
Date: January 1, 1938
Creator: Selden, Robert F & Spencer, Robert C

The influence of lateral stability on disturbed motions of an airplane with special reference to the motions produced by gusts

Description: Distributed lateral motions have been calculated for a hypothetical small airplane with various modifications of fin area and dihedral setting. Special combinations of disturbing factors to simulate gusts are considered and the influence of lateral stability on the motions is discussed. Fin area and wing dihedral were found to be of primary importance in side gusts. It was found that the rolling action of the wing with as much as 5 degrees dihedral was distinctly unfavorable, especially when the weathercock stability was small. It is pointed out that the greatest susceptibility to lateral disturbances lies in the inherent damping and coupling moments developed by the wing.
Date: January 1, 1938
Creator: Jones, Robert T

Interrelation of exhaust-gas constituents

Description: This report presents the results of an investigation conducted to determine the interrelation of the constituents of the exhaust gases of internal-combustion engines and the effect of engine performance on these relations. Six single-cylinder, liquid-cooled tests engines and one 9-cylinder radial air-cooled engine were tested. Various types of combustion chambers were used and the engines were operated at compression ratios from 5.1 to 7.0 using spark ignition and from 13.5 to 15.6 using compression ignition. The investigation covered a range of engine speeds from 1,500 to 2,100 r.p.m. The fuels used were two grades of aviation gasoline, auto diesel fuel, and laboratory diesel fuel. Power, friction, and fuel-consumption data were obtained from the single-cylinder engines at the same time that the exhaust-gas samples were collected.
Date: January 1, 1938
Creator: Gerrish, Harold C & Voss, Fred

The negative thrust and torque of several full-scale propellers and their application to various flight problems

Description: Negative thrust and torque data for 2, 3, and 4-blade metal propellers having Clark y and R.A.F. 6 airfoil sections were obtained from tests in the NACA 20-foot tunnel. The propellers were mounted in front of a radial engine nacelle and the blade-angle settings covered in the tests ranged from l5 degrees to 90 degrees. One propeller was also tested at blade-angle settings of 0 degree, 5 degrees, and 10 degrees. A considerable portion of the report deals with the various applications of the negative thrust and torque to flight problems. A controllable propeller is shown to have a number of interesting, and perhaps valuable, uses within the negative thrust and torque range of operation. A small amount of engine-friction data is included to facilitate the application of the propeller data.
Date: January 1, 1938
Creator: Hartman, Edwin P & Biermann, David

On some reciprocal relations in the theory of nonstationary flows

Description: In the theory of nonstationary flows about airfoils, the "indicial lift" function ksub1(s) of Wagner and the "alternating lift" function c(k) of Theodorsen have fundamental significance. This paper reports on some interesting relations of the nature of Fourier transforms that exist between these functions. General problems in transient flows about airfoils may be given a unified broad treatment when these functions are employed. Certain approximate results also are reported which are of notable simplicity, and an analogy with transient electrical flows is drawn.
Date: January 1, 1938
Creator: Garrick, I E

A photographic study of combustion and knock in a spark-ignition engine

Description: Report presents the results of a photographic study of the combustion in a spark-ignition engine using both Schlieren and flame photographs taken at high rates of speed. Although shock waves are present after knock occurs, there was no evidence of any type of sonic or supersonic compression waves existing in the combustion gases prior to the occurrence of knock. Artificially induced shock waves in the engine did not in themselves cause knock. The photographs also indicate that, although auto-ignition ahead of the flame front may occur in conjunction with knock, it is not necessary for the occurrence of knock. There is also evidence that the reaction is not completed in the flame front but continues for some time after the flame front has passed through the charge.
Date: January 1, 1938
Creator: Rothrock, A. M. & Spencer, R. C.