UNT Libraries Government Documents Department - 7 Matching Results

Search Results

Results: 1 - 7
open access

Effect of Fillers and of Mixing Procedure on the Strength of Plastic Materials

Description: Note presenting a study to prepare a series of molding powders with the use of a given plastic and given fillers in varying proportions and to determine the effect of the differences in composition of the molding powders on certain physical properties of standard test pieces molded from them.
Date: January 1943
Creator: Kynoch, William & Patronsky, L. A.
Item Type: Refine your search to only Report
open access

Large-Deflection Theory for End Compression of Long Rectangular Plates Rigidly Clamped Along Two Edges

Description: "The von Karman equations for flat plates are solved beyond the buckling load up to edge strains equal to eight time the buckling strain, for the extreme case of rigid clamping along the edges parallel to the load. Deflections, bending stresses, and membrane stresses are given as a function of end compressive load. The theoretical values of effective width are compared with the values derived for simple support along the edges parallel to the load" (p. 1).
Date: January 1943
Creator: Levy, Samuel & Krupen, Philip
Item Type: Refine your search to only Report
open access

Tests of Aluminum-Alloy Stiffened-Sheet Specimens Cut From an Airplane Wing

Description: "The specimens used in the present tests were cut from an actual airplane wing of the stressed-skin type. The specimens thus obtained were not representative of the usual type of laboratory specimens because the stiffeners were not exactly parallel nor evenly spaced and, in one case, the skin consisted of pieces of sheet of different thicknesses. The test data obtained indicate that the buckling strain of stiffened curved sheet can be computed with reasonable accuracy by the equation given by W… more
Date: January 1943
Creator: Holt, Marshall
Item Type: Refine your search to only Report
open access

Tests of flat panels with four types of stiffeners

Description: Report presenting testing of fifty-one aluminum-alloy panels as flat-end columns. The test specimens included all possible combinations of two lengths, four stiffener spacings, and four stiffener designs, and were mostly in duplicate pairs. Results regarding the panel bending tests, panel compression tests, and column tests of individual stiffeners are provided.
Date: January 1943
Creator: Niles, Alfred S.
Item Type: Refine your search to only Report
open access

Torsion tests of 24S-T aluminum-alloy noncircular bar and tubing

Description: From Summary: "Tests of 24S-T aluminum alloy have been made to determine the yield and ultimate strengths in torsion of noncircular bar and tubing. An approximate basis for predicting these torsional strength characteristics has been indicated. The results show that the torsional stiffness and maximum shearing stresses within the elastic range may be computed quite closely by means of existing formulas based on mathematical analysis and the membrane analogy."
Date: January 1943
Creator: Moore, R. L. & Paul, D. A.
Item Type: Refine your search to only Report
open access

Torsional Elastic Properties of 18:8 Chromium-Nickel Steel as Affected by Plastic Deformation and by Heat Treatment

Description: Note presenting a study made of the relationship between torsional stress, strain, and permanent set for 18:8 chromium-nickel steel in the annealed, half-hard, and hard conditions. The influence of plastic extension, plastic torsion, and annealing temperature on the torsional elastic properties is discussed.
Date: January 1943
Creator: Mebs, R. W. & McAdam, D. J., Jr.
Item Type: Refine your search to only Report
open access

Torsional strength of aluminum-alloy round tubing

Description: Report presenting an analysis of existing data on aluminum-alloy tubing with a wide range of plastic properties in order to establish a useful empirical relationship between tensile yield and ultimate strengths, diameter-thickness ratios, and torsional strengths within the range of plastic buckling.
Date: January 1943
Creator: Moore, R. L.
Item Type: Refine your search to only Report
Back to Top of Screen