UNT Libraries Government Documents Department - 190 Matching Results

Search Results

Results: 1 - 24 next
open access

Aerodynamic characteristics at high speeds of full-scale propellers having Clark Y blade sections

Description: From Introduction: "The single purpose of this paper is to make available the data obtained from tests of these two Clark Y section propellers as quickly as possible with no attempt being made to analyze the results or to compare them with other high-speed-propeller test results."
Date: October 26, 1948
Creator: Johnson, Peter J.
Item Type: Refine your search to only Report
open access

Aerodynamic characteristics of various configurations of a model of a 45 degree swept-wing airplane at a Mach number of 2.01

Description: An investigation has been conducted at the Langley 4- by 4-foot supersonic pressure tunnel at a Mach nmber of 2.01 to determine the aerodynamic characteristics of several configurations of a model of a 45 deg swept-wing airplane. The basic configuratin had a wing with 45 deg sweepback at the quarter-chord line, aspect ration 3.2, taper ration 0.468, NACA 65A005.5 sections just outboard of the inlet and NACA 65A003.7 sections at the tip. The wing was mounted slightly above the body center line a… more
Date: May 26, 1955
Creator: Spearman, M. Leroy; Driver, Cornelius & Robinson, Ross B.
Item Type: Refine your search to only Report
open access

Aerodynamic heat transfer and zero-lift of a flat windshield canopy on the NACA RM-10 research vehicle at high Reynolds numbers for a flight Mach number range from 1.5 to 3.0

Description: Report presenting the aerodynamic heat-transfer properties and zero-lift drag of a typical pilot's canopy as determined by a rocket-model flight test through a range of Mach and Reynolds numbers. The canopy had a 63 degree sweptback flat windshield, circular cross section, and an equivalent body fineness ratio of 7.0. Results regarding the canopy temperature distribution, canopy pressure distribution, heat-transfer coefficient, and drag are provided.
Date: September 26, 1956
Creator: Hoffman, Sherwood & Chauvin, Leo T.
Item Type: Refine your search to only Report
open access

Aerodynamic study of a wing-fuselage combination employing a wing swept back 63 degrees: Characteristics at a Mach number of 1.53 including effect of small variations of sweep

Description: Measured values of lift, drag, and pitching moment at a Mach number of 1.53 and Reynolds numbers of 0.31, 0.62, and 0.84 million are presented for a wing-fuselage combination having a wing leading-edge sweep angle of 63 degrees, an aspect ratio of 3.42, a taper ratio of 0.25, and an NACA 64A006 section in the stream direction. Data are also presented for sweep angles of 57.0 degrees, 60.4 degrees, 67.0 degrees, and 69.9 degrees. The experimentally determined characteristics were less favorable … more
Date: January 26, 1949
Creator: Madden, Robert T.
Item Type: Refine your search to only Report
open access

Air-flow characteristics of brazed and rolled wire filter cloth for transpiration-cooled afterburners

Description: From Introduction: "Because of variation in the static-pressure drop across the porous material and in the cooling air required along the length of afterburner combustion chambers, a prescribed distribution of permeability is usually necessary. However, as a preliminary investigation, this report is concerned only with the attainment of uniform permeability. The results of an experimental investigation, conducted at the NACA Lewis laboratory, to determine the permeabilities of five thick meshes… more
Date: October 26, 1953
Creator: Koffel, William K.
Item Type: Refine your search to only Report
open access

Altitude-Chamber Performance of British Rolls-Royce Nene II Engine 2: 18.41-Inch-Diameter Jet Nozzle

Description: Report presenting an altitude-chamber investigation to determine the altitude performance characteristics of the British Rolls-Royce Nene II turbojet engine with an 18.41-inch-diameter jet nozzles. Testing occurred at a range of simulated altitudes and ram-pressure ratios. Results regarding the simulated flight performance, generalized performance, and effect of jet-nozzle area on performance are provided.
Date: October 26, 1949
Creator: Armstrong, J. C.; Wilsted, H. D. & Vincent, K. R.
Item Type: Refine your search to only Report
open access

Altitude performance investigation of a high-temperature afterburner

Description: From Introduction: "In response to the ever-increasing need for high thrust augmentation, an investigation was conducted that had as its primary objective the attainment of maximum exhaust-gas temperature and thrust (ref. 1). The investigation reported herein was therefore conducted to ascertain the operational limits of the most promising high-temperature afterburner design of reference 1 and to determine its performance over a wind range of flight conditions."
Date: June 26, 1953
Creator: Huntley, S. C.; Auble, Carmon M. & Useller, James W.
Item Type: Refine your search to only Report
open access

Altitude Wind Tunnel Investigation of High-Temperature Afterburners

Description: From Introduction: "During previous investigations of afterburning conducted at the NACA Lewis laboratory (references 1 to 4, for example), the objective of obtaining high exhaust-gas temperatures and, consequently, maximum thrust augmentation was compromised to some extent in order to alleviate the problem of afterburner shell cooling. The primary objective of the investigation reported herein was therefore the attainment of maximum exhaust-gas temperature imposed by the cooling techniques pre… more
Date: June 26, 1952
Creator: Conrad, E. William & Campbell, Carl E.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loading 2 - Curtiss 838-1C2-18R1 Four-Blade Propeller

Description: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the performance of a Curtiss propeller with four 838-1C2-1SR1 blades on a YP-47M airplane at high blade loadings and engine powers. The study was made for a range of power coefficients between 0.30 and 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio, inasmuch as … more
Date: November 26, 1946
Creator: Wallner, Lewis E. & Sorin, Solomon M.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings 4 - Curtiss 732-1C2-0 Four-Blade Propeller

Description: "An altitude-wind-tunnel investigation has been made to determine the performance of a Curtiss 732-1C2-0 four-blade propeller on a YP-47M airplane at high blade loadings and engine power. Propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and .50" (p. 1).
Date: November 26, 1946
Creator: Saari, Martin J. & Sorin, Solomon M.
Item Type: Refine your search to only Report
open access

Analysis of pressure data obtained at transonic speeds on a thin low-aspect-ratio cambered delta wing-body combination

Description: From Introduction: "Wind-tunnel and flight tests have shown that conical leading-edge camber on a thin low-aspect-ratio delta wing results in increasing the lift-drag ratio at transonic and low supersonic speeds (refs. 1 and 2). References 3 and 4 present the results of two previous investigations of this general program. A more detailed analysis of the pressure distributions of reference 5 is presented herein in terms of total section loads and overall wing-body characteristics."
Date: September 26, 1958
Creator: Mugler, John P., Jr.
Item Type: Refine your search to only Report
open access

Analysis of some parameters used in correlating blowing-type boundary-layer control data

Description: Report presenting an examination of the limitations of the use of jet momentum coefficient as a correlating factor in comparing tests of blowing-type boundary-layer control. Theoretical and experimental data indicate that it should be an acceptable parameter where the duct pressures are large.
Date: September 26, 1956
Creator: Kelly, Mark W.
Item Type: Refine your search to only Report
open access

Analysis of the turbojet engine for propulsion of supersonic fighter airplanes

Description: An analytical investigation was made of two supersonic interceptor type airplanes to determine the most desirable turbojet engine characteristics for this application The airplanes were designed differently primarily because of the amount of subsonic flight incorporated in the flight plan--one flight having none and the other, a cruise radius of 400 nautical miles. Several power plant design variables were varied independently to determine the effect of changes in each parameter on airplane per… more
Date: October 26, 1953
Creator: Gabriel, David S.; Krebs, Richard P.; Wilcox, E. Clinton & Koutz, Stanley L.
Item Type: Refine your search to only Report
open access

Analytical Investigation of Fuel-Cooled Turbine Blades With Return-Flow Type of Finned Coolant Passages

Description: Memorandum presenting an investigation of coolant-flow rates for a turbine rotor blade with return-flow type of coolant-passage configuration formed by fins within a capped blade shell with both hydrogen and methane fuels as coolants. Results regarding spanwise blade and coolant temperature distributions, effects of coolant inlet temperature on hydrogen-coolant-flow requirements, comparison of return-flow-blade coolant requirements, effect of fin thickness and fin height, comparison of hydrogen… more
Date: June 26, 1957
Creator: Nachtigall, Alfred J. & Slone, Henry O.
Item Type: Refine your search to only Report
open access

Analytical investigation of fuel-cooled turbine blades with return-flow type of finned coolant passages

Description: From Introduction: "The purpose of this report was to investigate the possible use of engine fuels (hydrogen and methane) as coolants for turbine rotor blades and to determine the pressure-drop characteristics of these coolants for a turbine blade with a more effective coolant-passage configuration than that considered in reference 5 but for the same engine and flight conditions."
Date: June 26, 1957
Creator: Nachtigall, Alfred J. & Slone, Henry O.
Item Type: Refine your search to only Report
open access

Application of Theodorsen's Theory to Propeller Design

Description: "A theoretical analysis is presented for obtaining by use of Theodorsen's propeller theory the load distribution along a propeller radius to give the optimum propeller efficiency for any design condition. Examples are included to illustrate the method of obtaining the optimum load distributions for both single-rotating and dual-rotating propellers" (p. 1).
Date: July 26, 1948
Creator: Crigler, John L.
Item Type: Refine your search to only Report
open access

Arrangements of jet engine and airframe for increased range

Description: Report presenting an evaluation of a number of factors affecting engine-airframe arrangements in terms of range. Appropriate equations are developed and evaluated for a range of Mach numbers, ramjet and turbojet engines at several cycle temperatures, and two airplane lift-drag ratios. Some of the factors explored include inlet locations, jet cant for lift, engine moments for trim, a combination of the three factors, and the use of boundary layer in the engine.
Date: July 26, 1957
Creator: Luidens, Roger W.
Item Type: Refine your search to only Report
open access

Base pressures measured on several parabolic-arc bodies of revolution in free flight at Mach numbers from 0.8 to 1.4 and at large Reynolds numbers

Description: Report presenting base pressures measured on several fin-stabilized bodies of parabolic-arc profile in free flight at a range of Mach and Reynolds numbers. The bodies varied in length but had the same afterbody ratios. Results regarding base pressure coefficients, side pressure coefficients, effect of afterbody length, and drag are provided.
Date: October 26, 1951
Creator: Katz, Ellis & Stoney, William E., Jr.
Item Type: Refine your search to only Report
open access

Calculated Performance of a Mercury-Compressor-Jet Powered Airplane Using a Nuclear Reactor as an Energy Source

Description: Memorandum presenting an analysis of a system consisting of a mercury turbine-driven air compressor a mercury condenser wherein heat was added to the compressed air. The heat addition to the mercury is accomplished in an intermediate heat exchanger (mercury boiler) which has a liquid metal, other than mercury, circulating through the opposite side and through a nuclear reactor. Results regarding the turbine-exhaust pressure, turbine-inlet pressure, condenser-inlet Mach number, effect of nacelle… more
Date: September 26, 1951
Creator: Doyle, R. B.
Item Type: Refine your search to only Report
open access

Cascade investigation of a related series of 6-percent-thick guide-vane profiles and design charts

Description: Report presenting a new blade series designed to operate at near choking inlet Mach numbers and to have near maximum critical Mach numbers by employing high aerodynamic loading of the profiles in the leading-edge region and relatively straight trailing edges. Results regarding the aerodynamic characteristics and prediction of high-speed performance are provided.
Date: November 26, 1954
Creator: Dunavant, James C.
Item Type: Refine your search to only Report
open access

Combustion performance of two experimental turbojet annular combustors at conditions simulating high-altitude supersonic flight

Description: Report presenting an investigation of the performance of two experimental annular turbojet combustors at operating conditions typical of high-altitude supersonic flight. Results regarding combustion efficiency, combustor-outlet temperature profile, combustor pressure losses, and carbon and durability are provided.
Date: March 26, 1954
Creator: Zettle, Eugene V.; Norgren, Carl T. & Mark, Herman
Item Type: Refine your search to only Report
open access

Comparison between flight-measured and calculated span load distribution at high Mach numbers

Description: Report presenting an analysis of the spanwise loading using two different methods on the wing of an airplane for which pressure-distribution measurements were available from flight tests up to a Mach number of 0.866. A comparison between measured and calculated distributions was made on the basis of equal wing-panel normal-force coefficients.
Date: November 26, 1947
Creator: Rolls, L. Stewart
Item Type: Refine your search to only Report
Back to Top of Screen