UNT Libraries Government Documents Department - 25,095 Matching Results

Search Results

D-0 South End Cap Calorimeter Cold Test Results

Description: The South endcap calorimeter vessel was moved into Lab A on Sept. 18, 1990. A cooldown of the pressure vessel with liquid nitrogen was performed on Sept. 26 to check the vessel's integrity. With the pressure vessel cold, the insulating vacuum was monitored for leaks. Through out the testing, the insulating vacuum remained good and the vessel passed the test. The cold test was carried out per the procedures of D-Zero engineering note 3740.220-EN-250. The test was very similar to the cold test performed on the Central Calorimeter in October of 1987. The test of the ECS was performed in the same manner using the same equipment as the ECN cold test. Reference D-Zero engineering notes 3740.210-EN-122, 3740.000-EN-I07, and 3740.210-EN-II0 for information about the CC cold test. Reference EN-260 for the results of the ECN cold test. The insulating vacuum space was pumped on while equipment was being connected to the pressure vessel. Two hours after starting to pump with the blower the vacuum space pressure was at about 40 microns. The pumping continued overnight (another 16 hours). In the morning the pressure was 11.5 microns. A rate of rise test was performed. With the pump valved off, the pressure rose to 14 microns within 5 minutes and then rose to 16 microns in 6 hours (0.33 microns/hour). After all connections were made to the pressure vessel, a vacuum pump with an estimated effective pumping speed of about 70 scfm was valved on. After 18 hours, the pressure vessel was down to 270 microns. An additional day of pumping took the pressure down to only 250 microns. A leak was then found and fixed around the seal of the rupture disc. The pump was put on line again. The pressure vessel with pump on line was 27 microns after 16.5 ...
Date: November 26, 1990
Creator: Rucinski, R.

1.1-meter bore, 8-Tesla test facility

Description: The design and fabrication of a 1.1-m bore superconducting coil for an 8- T facility at Lawrence Livermore Laboratory are discussed. This facility will provide the backing field required for testing large multifilamentary Nb$sub 3$Sn coils as part of the superconductor development program at Livermore. The magnet measures 1.85 m o.d., is 1.5 m in length, and is solenoid wound in four separate modules. Total cold weight of the assembly is 18,000 Kg. A NbTi superconductor is used throughout with a gradation of current density within the magnet to provide complete cryostatic stability. The preliminary design of a large 3500-A multifilamentary Nb$sub 3$Sn insert magnet is also included. Together, the backing coil and insert magnets are designed to produce a 12-T central field in a 0.4m bore. The ''equal area'' theory of cryostatic stability is applied in the design of both magnet systems and is discussed in detail. A large open-mouth cryostat is used and measures 2 m in diameter and 3.7 m in length. Details of Dewar design and the refrigeration requirements are included. (auth)
Date: November 19, 1975
Creator: Nelson, R.; Cornish, D.; Zbasnik, J.; Sackett, S. & Taylor, C.

1.5 megawatt dc chopper power supplies for plasma shape control on Doublet III

Description: The Doublet III device is designed to study noncircular plasmas, including doublet and dee-shaped cross-sections. The plasma shape is determined by a system of 24 field-shaping coils which surround the vacuum vessel. Control of the magnetic flux linking these coils allows the plasma shape to be varied and controlled. This paper describes the high-speed dc chopper which is a major component of the field-shaping coil power system. The high-speed dc choppers, with a frequency response of up to 5 kHz and a switching power capability of 1.5 megawatts are used for fine tuning and feedback control of the plasma position and shape. The design and operation of two 1.5 megawatt, 3 kHz choppers used on closed loop plasma control experiments will be presented.
Date: November 1979
Creator: Rock, P. J. & Wesley, J. C.

1-Dimensional simulation of thermal annealing in a commercial nuclear power plant reactor pressure vessel wall section

Description: The objective of this work was to provide experimental heat transfer boundary condition and reactor pressure vessel (RPV) section thermal response data that can be used to benchmark computer codes that simulate thermal annealing of RPVS. This specific protect was designed to provide the Electric Power Research Institute (EPRI) with experimental data that could be used to support the development of a thermal annealing model. A secondary benefit is to provide additional experimental data (e.g., thermal response of concrete reactor cavity wall) that could be of use in an annealing demonstration project. The setup comprised a heater assembly, a 1.2 in {times} 1.2 m {times} 17.1 cm thick [4 ft {times} 4 ft {times} 6.75 in] section of an RPV (A533B ferritic steel with stainless steel cladding), a mockup of the {open_quotes}mirror{close_quotes} insulation between the RPV and the concrete reactor cavity wall, and a 25.4 cm [10 in] thick concrete wall, 2.1 in {times} 2.1 in [10 ft {times} 10 ft] square. Experiments were performed at temperature heat-up/cooldown rates of 7, 14, and 28{degrees}C/hr [12.5, 25, and 50{degrees}F/hr] as measured on the heated face. A peak temperature of 454{degrees}C [850{degrees}F] was maintained on the heated face until the concrete wall temperature reached equilibrium. Results are most representative of those RPV locations where the heat transfer would be 1-dimensional. Temperature was measured at multiple locations on the heated and unheated faces of the RPV section and the concrete wall. Incident heat flux was measured on the heated face, and absorbed heat flux estimates were generated from temperature measurements and an inverse heat conduction code. Through-wall temperature differences, concrete wall temperature response, heat flux absorbed into the RPV surface and incident on the surface are presented. All of these data are useful to modelers developing codes to simulate RPV annealing.
Date: November 1, 1994
Creator: Nakos, J. T.; Rosinski, S. T. & Acton, R. U.

A-01 metals in stormwater runoff evaluation

Description: As a part of the A-01 investigation required by the NPDES permit, an investigation was performed to ascertain the concentrations of metals specifically copper (Cu), lead (Pb), and zinc (Zn) in stormwater being discharged through the outfall. This information would indicate whether all water being discharged would have to be treated or if only a portion of the discharged stormwater would have to be treated. A study was designed to accomplish this. The first goal was to determine if the metal concentrations increased, decreased, or remained the same as flow increased during a rain event. The second goal was to determine if the concentrations in the storm water were due to dissolved. The third goal was to obtain background data to ascertain if effluent credits could be gained due to naturally occurring metals.Samples from this study were analyzed and indicate that the copper and lead values increase as the flow increases while the zinc values remain essentially the same regardless of the flow rate. Analyses of samples for total metals, dissolved metals, TSS, and metals in solids was complicated because in all cases metals contamination was found in the filters themselves. Some conclusions can be derived if this problem is taken into account when analyzing the data. Copper concentrations in the total and dissolved fractions as well as the TSS concentrations followed the hydrograph at this outfall but the copper in solids concentration appeared to peak in the first flush and decline to nondetectable rapidly over the course of the storm event. Lead was present in the total analysis but not present in the dissolved fraction or the solids fraction of the samples. The data for zinc was interesting in that the dissolved fractions were higher than the total fraction in three out of four samples. This is probably due ...
Date: November 6, 1997
Creator: Eldridge, L. L.

1: Redox chemistry of bimetallic fulvalene complexes; 2: Oligocyclopentadienyl complexes

Description: The electrochemistry of the heterobimetallic complexes (fulvalene)WFe(CO){sub 5} (30) and (fulvalene)WRu(CO){sub 5} (31) has been investigated. Compound 30 is reduced in two one-electron processes, and this behavior was exploited synthetically to prepare a tetranuclear dimer by selective metal reduction. Complex 31 displayed a distinction between the metals upon reoxidation of the dianion, allowing the formation of a dimer by selective metal anion oxidation. The redox behavior of 30 led to an investigation of the use of electrocatalysis to effect metal-specific ligand substitution. It was found that reduction of 30 with a catalytic amount of CpFe(C{sub 6}Me{sub 6}) (97) in the presence of excess P(OMe){sub 3} or PMe{sub 3} led to the formation of the zwitterions (fulvalene)[W(CO){sub 3}{sup {minus}}][Fe(CO)PR{sub 3}{sup +}] (107, R = P(OMe){sub 3}; 108, R = PMe{sub 3}). Compound 31 also displayed unique behavior with different reducing agents, as the monosubstituted zwitterion (fulvalene)[W(CO){sub 3}{sup {minus}}][Ru(CO){sub 2}(PMe{sub 3}){sup +}] was obtained when 97 was used while the disubstituted complex (fulvalene) [W(CO){sub 3}{sup {minus}}] [Ru(CO)(PMe{sub 3}){sub 2}{sup +}] was produced when Cp*Fe(C{sub 6}Me{sub 6}) was the catalyst. Potential synthetic routes to quatercyclopentadienyl complexes were also explored. Various attempts to couple heterobimetallic fulvalene compounds proved to be unsuccessful. 138 refs.
Date: November 1, 1993
Creator: Brown, D. S.

2-D Axisymmetric Line Transport

Description: The methods used in the ALTAIR code for computing the transfer of spectral line radiation in two-dimensional axially-symmetric geometry are described. ALTAIR uses a variable-Eddington-tensor approach, in which the transfer equation of non-coherent line scattering is written in moment form, and the moments are closed with an assumed tensor relating the monochromatic pressure tensor and energy density; this Eddington tensor is obtained self-consistently using an accurate angle-dependent solution of the transfer equation. The finite element method for solving the moment system, and the discontinuous finite element method for solving the S{sub n} equation of transfer are described. Two applications of the method are discussed: line formation in uniform cylinders with different length-diameter ratios, and monochromatic transfer on an irregular x-y mesh (the Mordant test problem). 13 refs., 2 figs.
Date: November 20, 1990
Creator: Castor, John I.; Dykema, Pieter G & Klein, Richard I.

2-D electric fields and drifts near the magnetic separatrix in divertor tokamaks

Description: A 2-D calculation is presented for the transport of plasma in the edge region of a divertor tokamak solving continuity, momentum, and energy balance fluid equations. The model uses anomalous radial diffusion, including perpendicular ion momentum, and classical cross-field drifts transport. Parallel and perpendicular currents yield a self-consistent electrostatic potential on both sides of the magnetic separatrix. Outside the separatrix, the simulation extends to material divertor plates where the incident plasma is recycled as neutral gas and where the plate sheath and parallel currents dominate the potential structure. Inside the separatrix, various radial current terms - from viscosity, charge-exchange and poloidal damping, inertia, and {triangledown}B - contribute to the determining the potential. The model rigorously enforces cancellation of gyro-viscous and magnetization terms from the transport equations. The results emphasize the importance of E x B particle flow under the X-point which depends on the sign of the toroidal magnetic field. Radial electric field (E{sub y}) profiles at the outer midplane are small with weak shear when high L-mode diffusion coefficients are used and are large with strong shear when smaller H-mode diffusion coefficients are used. The magnitude and shear of the electric field (E{sub y}) is larger both when the core toroidal rotation is co-moving with the inductive plasma current and when the ion {triangledown}B-drift is towards the single-null X-point.
Date: November 15, 1998
Creator: Mattor, N.; Porter, G. D.; Rognlien, T. D. & Ryutov, D. D.

2-D linear motion system. Innovative technology summary report

Description: The US Department of Energy's (DOE's) nuclear facility decontamination and decommissioning (D and D) program requires buildings to be decontaminated, decommissioned, and surveyed for radiological contamination in an expeditious and cost-effective manner. Simultaneously, the health and safety of personnel involved in the D and D activities is of primary concern. D and D workers must perform duties high off the ground, requiring the use of manlifts or scaffolding, often, in radiologically or chemically contaminated areas or in areas with limited access. Survey and decontamination instruments that are used are sometimes heavy or awkward to use, particularly when the worker is operating from a manlift or scaffolding. Finding alternative methods of performing such work on manlifts or scaffolding is important. The 2-D Linear Motion System (2-D LMS), also known as the Wall Walker{trademark}, is designed to remotely position tools and instruments on walls for use in such activities as radiation surveys, decontamination, and painting. Traditional (baseline) methods for operating equipment for these tasks require workers to perform duties on elevated platforms, sometimes several meters above the ground surface and near potential sources of contamination. The Wall Walker 2-D LMS significantly improves health and safety conditions by facilitating remote operation of equipment. The Wall Walker 2-D LMS performed well in a demonstration of its precision, accuracy, maneuverability, payload capacity, and ease of use. Thus, this innovative technology is demonstrated to be a viable alternative to standard methods of performing work on large, high walls, especially those that have potential contamination concerns. The Wall Walker was used to perform a final release radiological survey on over 167 m{sup 2} of walls. In this application, surveying using a traditional (baseline) method that employs an aerial lift for manual access was 64% of the total cost of the improved technology. However, for areas over approximately ...
Date: November 1, 1998

2 meg-ampere prototype levitated coil for multipole fusion

Description: The coils major diameter is 1.0 meter and it occupies a cross-section which is about 0.2 meter minor in diameter. The prototype coil will carry four times the current of the largest such magnet built to date. As a result, the peak induction in the coil is about 8 T and the stored magnetic energy will be around 3 MJ. The paper describes the proposed Nb/sub 3/SN superconductor, the quench protection system which is based on the LBL shorted secondary concept, the isochroic refrigeration storage system which stores about 5 kJ of refrigeration between 4.5/sup 0/K and 7/sup 0/K, and the persistent switch.
Date: November 1, 1979
Creator: Green, M.A. & Glueck, R.

2-MV electrostatic quadrupole injector for heavy-ion fusion

Description: High current and low emittance are principal requirements for heavy-ion injection into a linac driver for inertial fusion energy. An electrostatic quadrupole (ESQ) injector is capable of providing these high charge density and low emittance beams. We have modified the existing 2-MV Injector to reduce beam emittance and to double the pulse length. We characterize the beam delivered by the modified injector to the High Current Transport Experiment (HCX) and the effects of finite rise time of the extraction voltage pulse in the diode on the beam head. We demonstrate techniques for mitigating aberrations and reducing beam emittance growth in the injector.
Date: November 10, 2004
Creator: Bieniosek, F.M.; Celata, C.M.; Henestroza, E.; Kwan, J.W.; Prost, L. & Seidl, P.A.

3-D Computations and Measurements of Accelerator Magnets for the APS

Description: The Advanced Photon Source (APS), now under construction at Argonne National Laboratory (ANL), requires dipole, quadrupole, sextupole, and corrector magnets for each of its circular accelerator systems. Three-dimensional (3-D) field computations are needed to eliminate unwanted multipole fields from the ends of long quadrupole and dipole magnets and to guarantee that the flux levels in the poles of short magnets will not cause saturation. Measurements of the magnets show good agreement with the computations.
Date: 1993-11~
Creator: Turner, L. R.; Kim, S. H. & Kim, K.

3-D Measurement of Deformation Microstructure of Al(0.2%)Mg Using Submicron Resolution White X-Ray Microbeams

Description: We have used submicron-resolution white x-ray microbeams on the MHATT-CAT beamline 7-ID at the Advanced Photon Source to develop techniques for three-dimensional investigation of the deformation microstructure in a 20% plane strain compressed Al(0.2%)Mg tri-crystal. Kirkpatrick-Baez mirrors were used to focus white radiation from an undulator to a 0.7 x 0.7 {micro}m{sup 2} beam that was scanned over bi- and tri-crystal regions near the triple-junction of the tri-crystal. Depth resolution along the x-ray microbeam of less than 5 microns was achieved by triangulation to the diffractibn source point using images taken at a series of CCD distances from the microbeam. Computer indexing of the deformation cell structure in the bi-crystal region provided orientations of individual subgrains to {approximately}0.01 degrees, making possible detailed measurements of the rotation axes between individual cells.
Date: November 29, 1999
Creator: Larson, B. C.; tamura, N.; Chung, J.-S.; Ice, G. E.; Budai, J. D.; Tischler, J. Z. et al.

3-D Reservoir and Stochastic Fracture Network Modeling for Enhanced Oil Recovery, Circle Ridge Phosphoria/Tensleep Reservoir, Wind River Reservation, Arapaho and Shoshone Tribes, Wyoming

Description: This report describes the results made in fulfillment of contract DE-FG26-00BC15190, ''3-D Reservoir and Stochastic Fracture Network Modeling for Enhanced Oil Recovery, Circle Ridge Phosphoria/Tensleep Reservoir, Wind River Reservation, Arapaho and Shoshone Tribes, Wyoming''. The goal of this project is to improve the recovery of oil from the Tensleep and Phosphoria Formations in Circle Ridge Oilfield, located on the Wind River Reservation in Wyoming, through an innovative integration of matrix characterization, structural reconstruction, and the characterization of the fracturing in the reservoir through the use of discrete fracture network models. Fields in which natural fractures dominate reservoir permeability, such as the Circle Ridge Field, often experience sub-optimal recovery when recovery processes are designed and implemented that do not take advantage of the fracture systems. For example, a conventional waterflood in a main structural block of the Field was implemented and later suspended due to unattractive results. It is estimated that somewhere less than 20% of the OOIP in the Circle Ridge Field have been recovered after more than 50 years' production. Marathon Oil Company identified the Circle Ridge Field as an attractive candidate for several advanced IOR processes that explicitly take advantage of the natural fracture system. These processes require knowledge of the distribution of matrix porosity, permeability and oil saturations; and understanding of where fracturing is likely to be well-developed or poorly developed; how the fracturing may compartmentalize the reservoir; and how smaller, relatively untested subthrust fault blocks may be connected to the main overthrust block. For this reason, the project focused on improving knowledge of the matrix properties, the fault block architecture and to develop a model that could be used to predict fracture intensity, orientation and fluid flow/connectivity properties. Knowledge of matrix properties was greatly extended by calibrating wireline logs from 113 wells with incomplete or older-vintage ...
Date: November 18, 2002
Creator: La Pointe, Paul; Hermanson, Jan; Parney, Robert; Eiben, Thorsten; Dunleavy, Mike; Steele, Ken et al.


Description: This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). We have developed a method for solving the neutral-particle transport equation on 3-D unstructured hexahedral meshes using a S{sub n} discretization in angle in conjunction with a discontinuous finite-element discretization in space and a multigroup discretization in energy. Previous methods for solving this equation in 3-D have been limited to rectangular meshes. The unstructured-mesh method that we have developed is far more efficient for solving problems with complex 3-D geometric features than rectangular-mesh methods. In spite of having to make several compromises in our spatial discretization technique and our iterative solution technique, our method has been found to be both accurate and efficient for a broad class of problems.
Date: November 1, 2000
Creator: Morel, J. & McGhee, J.

3-Dimensional Flow Modeling of a Proposed Hanford Waste Treatment Plant Ion-Exchange Column Design

Description: Historically, it has been assumed that the inlet and outlet low activity waste plenums would be designed such that a nearly uniform velocity profile would be maintained at every axial cross-section (i.e., providing nearly 100 percent use of the resin bed). With this proposed design, we see a LAW outlet distributor that results in significant non-axial velocity gradients in the bottom regions of the bed with the potential to reduce the effectiveness'' of the overall resin bed. The magnitude of this efficiency reduction depends upon how far up-gradient of the LAW outlet these non-axial velocities persist and to what extent a ''dead-zone'' is established beneath the LAW outlet. This can impact loading and elution performance of the ion-exchange facility. Currently, no experimental studies are planned. The primary objective of this work was, through modeling, to assess the fluid dynamic impact on ''effective'' resin volume of the full-scale column based on its normal operation using a recently proposed LAW outlet distributor. The analysis effort was limited to 3-D flow only analyses (i.e., no follow on transport analyses) with 3-D particle tracking to approximate the impact that a nonaxial velocity profile would have on bed ''effectiveness''. Additional analyses were performed to estimate under nominal operating conditions the thermal temperature rise across a loaded resin bed and within its particles. Hydrogen bubble formation is not considered in the heat transfer analysis or in the determination of minimum flowrate. All modeling objectives were met.
Date: November 2002
Creator: Aleman, Sebastian

3 Dimensional radiation transport in dispersive media

Description: In plasmas the collective motion of free electrons affects the propagation of radiation by bending the light ray trajectory. The closer the light wave frequency is to the electron plasma frequency in value, the more pronounced the effect. We will present the results of radiation transport calculations in 3 spatial dimensions in the refractive plasma environment and compare the calculation to one done where the ray bending has been neglected (straight line ray paths). We also present the numerical method used for the refractive transport. 4 refs., 5 figs.
Date: November 1, 1990
Creator: Mayle, R.W.

3 mm Anisotropy Measurement: On the Quadrupole Component in theCosmic Background Radiation

Description: We have mapped the large-scale anisotropy in the cosmic background radiation at 3 mm wavelength using a liquid-helium-cooled balloon-borne radiometer sensitive enough to detect the dipole in one gondola rotation (1 minute). Statistical errors on the dipole and quadrupole components are below 0.1 mK with less than 0.1 m K galactic contribution. We find a dipole consistent with previous measurements but disagree with recent quadrupole reports. The measurement is also useful in searching for spectral distortions.
Date: November 1, 1982
Creator: Lubin, Philip M.; Epstein, Gerald L. & Smoot, George F.

5 MeV Mott polarimeter for rapid precise electron beam polarization measurements

Description: Low energy (E{sub k} = 100 keV) Mott scattering polarimeters are ill-suited to support operations foreseen for the polarized electron injector at Jefferson Lab. One solution is to measure the polarization at 5 MeV where multiple and plural scattering are unimportant and precision beam monitoring is straightforward. The higher injector beam current offsets the lower cross-sections; measured rates scale to 1 kHz/{mu}A with a 1 {mu}m thick gold target foil.
Date: November 1, 1997
Creator: Price, J.S.; Poelker, B.M. & Sinclair, C.K.

6.70 EV Resonance in U²³⁸

Description: "Using the Brookhaven fast chopper, transmission curves were obtained for the 6.70 +/- .06 ev resonance in U238 using four different thicknesses of natural uranium metal." The measurements for the transmission curves are summarized in the table provided.
Date: November 9, 1953
Creator: Levin, Jules S.