UNT Libraries Government Documents Department - 11 Matching Results

Search Results

Application of Integrated Reservoir Management and Reservoir Characterization to Optimize Infill Drilling.

Description: A total of 18 wells, 14 producers and 4 injection wells, were drilled and completed during the Field Demonstration portion of the project. These 18 wells are all currently in service, with the producing wells going on-line between May and September 1996, and the injection wells going into service between August and December 1996. Current Unit production is approximately 3,100 BOPD, of which approximately 800 BOPD is being contributed from the 14 Project 10-acre producing wells (Figure 1). A revision in the Statement of Work was approved to allow for the drilling of additional 10-acre infill wells or injection well conversions as budget constraints allow.
Date: January 15, 1998

[Calibration methods for neutron diagnostics at Omega]. DOE/NLUF final report

Description: The investigation of Calibration Methods for Neutron Diagnostics at Omega is still underway. The data shown here is a compilation of measurements taken at Omega during the time of the grant. The data set has been updated with additional information taken this year. The neutron yield from an ICF event was determined by measuring the activity of an aluminum sample activated by target-produced DT neutrons. The radioactive nuclei {sup 24}Na and {sup 27}Mg, which were produced via the {sup 27}Al(n,{alpha}){sup 24}Na and {sup 27}Al(n,p){sup 27}Mg direct reactions, beta decay to excited states of {sup 24}Mg and {sup 27}Al respectively. These excited states then emitted gamma rays as the nuclei de-excite to their respective ground states. The gamma rays are detected and counted. From their numbers the neutron yield is determined.
Date: January 15, 1998
Creator: Padalino, S.

Development & Testing of Industrial Scale, Coal Fired Combustion System, Phase 3

Description: In the third quarter of calendar year 1997, 10 days of tests on the 20 MMBtu/hr combustor-boiler facility were performed. The total test days on the Philadelphia facility to the end of September 1997 was 93, of which 19 tests were implemented as part of another DOE project. This exceeds the planned 63 test days for this project. Key project objectives have been exceeded, including NO emissions as low as 0.07 lb/MMBtu and SO emissions as low as 0.2 x 2 lb/MMBtu. The tests in the present quarter focussed on further optimizing post-combustion sorbent injection for SO2 and NOx control processes. The results were in the same range as in previous tests. In addition, initial tests of Coal Tech�s post-combustion NOx control process were implemented on a 100 MW and a 37 MW utility boiler, and NOx reductions as high as 40% were measured in the latter boiler.
Date: January 15, 1998
Creator: Zauderer, Bert

Dual Axis Radiographic Hydrodynamic Test Facility mitigation action plan. Annual report for 1997

Description: This Mitigation Action Plan Annual Report (MAPAR) has been prepared by the US Department of Energy (DOE) as part of implementing the Dual Axis Radiographic Hydrodynamic Test Facility (DARHT) Mitigation Action Plan (MAP). This MAPAR provides a status on specific DARHT facility design- and construction-related mitigation actions that have been initiated in order to fulfill DOE`s commitments under the DARHT MAP. The functions of the DARHT MAP are to (1) document potentially adverse environmental impacts of the Phased Containment Option delineated in the Final EIS, (2) identify commitments made in the Final EIS and ROD to mitigate those potential impacts, and (3) establish Action Plans to carry out each commitment (DOE 1996). The DARHT MAP is divided into eight sections. Sections 1--5 provide background information regarding the NEPA review of the DARHT project and an introduction to the associated MAP. Section 6 references the Mitigation Action Summary Table which summaries the potential impacts and mitigation measures; indicates whether the mitigation is design-, construction-, or operational-related; the organization responsible for the mitigation measure; and the projected or actual completion data for each mitigation measure. Sections 7 and 8 discuss the Mitigation Action Plan Annual Report and Tracking System commitment and the Potential Impacts, Commitments, and Action Plans respectively. Under Section 8, potential impacts are categorized into five areas of concern: General Environment, including impacts to air and water; Soils, especially impacts affecting soil loss and contamination; Biotic Resources, especially impacts affecting threatened and endangered species; Cultural/Paleontological Resources, especially impacts affecting the archeological site known as Nake`muu; and Human Health and Safety, especially impacts pertaining to noise and radiation. Each potential impact includes a brief statement of the nature of the impact and its cause(s). The commitment made to mitigate the potential impact is identified and the Action Plan for each commitment ...
Date: January 15, 1998
Creator: Haagenstad, H.T.

Energy and waste reduction in the wood fiber and fuel industry utilizing a long wave length catalytic infrared drying system. Progress report Number 3

Description: Following the testing of the Cat-Tec handling system, detail design work commenced both at the Catalytic Industrial Systems (CIS) Kansas facility and at the Cat-Tec offices in Minneapolis for the mating of the heating and handling system elements of the catalytic infrared particulate dryer. A used equipment looped handling system designed to feed and recirculate the test material was procured and shipped to CIS in anticipation of the on-site testing. Evaluation of the findings of the test results led the joint CIS-Cat-Tec design team to conclude that the unit to be provided to Lignetics for testing needed to have approximately 120 square feet of agitation bed and approximately 100 feet of infrared generation surfaces. The overall size was thus increased approximately 50% from the initial test unit.
Date: January 15, 1998
Creator: Davis, R.

Environmental-performance research priorities: Wood products. Final report

Description: This report describes a research plan to establish environmental, energy, and economic performance measures for renewable building materials, and to identify management and technology alternatives to improve environmental performance in a cost-effective manner. The research plan is designed to: (1) collect environmental and economic data on all life-cycle stages of the materials, (2) ensure that the data follows consistent definitions and collection procedures, and (3) develop analytical procedures for life-cycle analysis to address environmental performance questions. The research will be subdivided into a number of individual project modules. The five processing stages of wood used to organize the research plan are: (1) resource management and harvesting; (2) processing; (3) design and construction of structures; (4) use, maintenance, and disposal; and (5) waste recycling. Individual research module descriptions are provided in the report, as well as assessment techniques, research standards and protocol, and research management. 13 refs., 5 figs., 3 tabs.
Date: January 15, 1998

Enzyme catalysts for a biotechnology-based chemical industry. Quarterly progress report, September 29--December 28, 1997

Description: The goal of this research is to engineer enzymes to be efficient and economically attractive catalysts for the chemical industry. The author is attempting to demonstrate generally-applicable approaches to enzyme improvement as well as develop specific catalysts for potential industrial application. In this report attention is focused on random mutagenesis of pNB esterase -- improved activity and stability. The most thermostable esterases obtained by sequential random mutagenesis (6H7) and random mutagenesis plus recombination (6sF9) each contain 9 amino acid mutations and a number of silent mutations, relative to the wild-type sequence. Eight of the mutations are present in both genes, for a total of ten potentially adaptive mutations. Because several of these mutations occurred in the same generation, it is difficult to identify the mutations responsible for the increases in activity and stability. In order to aid in this identification, the thermostable genes were recombined with the wild-type gene, in hopes of removing neutral mutations. The gene from the first-generation variant, with five amino acid substitutions was also recombined with wild-type.
Date: January 15, 1998
Creator: Arnold, F.H.

Evaluation of Reservoir Wettability and its Effect on Oil Recovery.

Description: We report on the first year of the project, `Evaluation of Reservoir Wettability and its Effect on Oil Recovery.` The objectives of this five-year project are (1) to achieve improved understanding of the surface and interfacial properties of crude oils and their interactions with mineral surfaces, (2) to apply the results of surface studies to improve predictions of oil production from laboratory measurements, and (3) to use the results of this research to recommend ways to improve oil recovery by waterflooding. During the first year of this project we have focused on understanding the interactions between crude oils and mineral surfaces that establish wetting in porous media. As background, mixed-wetting and our current understanding of the influence of stable and unstable brine films are reviewed. The components that are likely to adsorb and alter wetting are divided into two groups: those containing polar heteroatoms, especially organic acids and bases; and the asphaltenes, large molecules that aggregate in solution and precipitate upon addition of n-pentane and similar agents. Finally, the test procedures used to assess the extent of wetting alteration-tests of adhesion and adsorption on smooth surfaces and spontaneous imbibition into porous media are introduced. In Part 1, we report on studies aimed at characterizing both the acid/base and asphaltene components. Standard acid and base number procedures were modified and 22 crude oil samples were tested. Our approach to characterizing the asphaltenes is to focus on their solvent environment. We quantify solvent properties by refractive index measurements and report the onset of asphaltene precipitation at ambient conditions for nine oil samples. Four distinct categories of interaction mechanisms have been identified that can be demonstrated to occur when crude oils contact solid surfaces: polar interactions can occur on dry surfaces, surface precipitation is important if the oil is a poor solvent for ...
Date: January 15, 1998
Creator: Buckley, J.S.

Feasibility analysis report for hybrid non-thermal plasma reactors

Description: The purpose of the Strategic Environmental Research and Development Program (SERDP) project CP-1038 is to evaluate and develop non-thermal plasma (NTP) reactor technology for Department of Defense (DoD) air emissions control applications. The primary focus is on oxides of nitrogen (NO{sub x}) and a secondary focus on hazardous air pollutants (HAPs), especially volatile organic compounds (VOCs). Examples of NO{sub x} sources are jet engine test cells (JETCs) and diesel-engine powered electrical generators. Examples of VOCs are organic solvents used in painting, paint-stripping, and parts cleaning. Because pollutant-containing air-emission streams within the Department of Defense (DoD) frequently span a broad range of pollutant concentrations, flow rates, and gas conditions (e.g., temperature, humidity), a single type of NTP reactor is not expected to fit all types of emissions streams. Additionally, stand-alone NTP reactors may provide neither an adequate means of pollutant removal nor an acceptable economic solution. Therefore, hybrid systems (combinations of different NTP reactor types or architectures), which employ adsorbents and/or catalytic media are being examined by researchers in this field. This report is intended to provide a preliminary summary analysis of a few representative hybrid systems as a means of introducing the hybrid or staged-system concept.
Date: January 15, 1998
Creator: Rosocha, L.A.

Investigation of properties and performance of ceramic composite components: Final report on Phases 3 and 4

Description: The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for longer-term fossil energy applications as well as for generic needs of various fossil fuel technologies. The research program of the Materials Response Group at Virginia Tech addresses the need for reliable and durable structural ceramic composites to perform in high temperature environments. The research effort provides an experimental and analytical basis for the transition from properties of materials to performance of actual component structures. Phases 1 and 2 of the present program focused on the development of test capabilities, initial studies of component mechanical response under various conditions and the development of a life prediction methodology. These efforts have been described in previous reports. This report summarizes the major tasks completed under Phases 3 and 4 of the project. Overall, the authors have made significant progress in a broad spectrum of tasks in this program. Their efforts have encompassed component evaluation, assessment of new SiC-based composites with improved high-temperature potential, development of oxide coating materials for SiC, and the extension and development of new models for predicting the durability of composite components under specific operating conditions for various CMC applications. Each of these areas of work is an important area for achieving the ultimate goal of usable SiC-based composites in high-temperature corrosive environments typical of fossil energy applications.
Date: January 15, 1998
Creator: Curtin, W.A.; Halverson, H.; Carter, R.H.; Miraj, N. & Reifsnider, K.L.

Southeast geysers effluent pipeline project. Final report

Description: The project concept originated in 1990 with the convergence of two problems: (1) a need for augmented injection to mitigate declining reservoir productivity at the Geysers; and (2) a need for a new method of wastewater disposal for Lake County communities near the The Geysers. A public/private partnership of Geysers operators and the Lake County Sanitation District (LACOSAN) was formed in 1991 to conduct a series of engineering, environmental, and financing studies of transporting treated wastewater effluent from the communities to the southeast portion of The Geysers via a 29-mile pipeline. By 1994, these evaluations concluded that the concept was feasible and the stakeholders proceeded to formally develop the project, including pipeline and associated facilities design; preparation of an environmental impact statement; negotiation of construction and operating agreements; and assembly of $45 million in construction funding from the stakeholders, and from state and federal agencies with related program goals. The project development process culminated in the system`s dedication on October 16, 1997. As of this writing, all project components have been constructed or installed, successfully tested in compliance with design specifications, and are operating satisfactorily.
Date: January 15, 1998
Creator: Dellinger, M.