UNT Libraries Government Documents Department - 13,806 Matching Results

Search Results

The 5- by 7-meter wind tunnel of the DVL

Description: The report contains a description of the DVL wind tunnel. According to the cones fixed, an elliptical stream with axes 5 by 7 meters and length 9 meters, or a stream 6 by 8 meters in cross section and 11 meters in length is available. The top speed with the smaller cone is 65 meters per second. The testing equipment consists of an automatic six-component balance and a test rig for propellers and engines up to 650 horsepower.
Date: October 3, 1936
Creator: Kramer, M

The 6-foot-4-inch wind tunnel at the Washington Navy Yard

Description: Report discussing the 6-foot-4-inch wind tunnel and its auxiliary equipment has proven itself capable of continuous and reliable output of data. The real value of the tunnel will increase as experience is gained in checking the observed tunnel performance against full-scale performance. Such has been the case of the 8- by 8-foot tunnel, and for that reason the comparison in the calibration tests have been presented.
Date: August 1935
Creator: Desmond, G L & Mccrary, J A

The 7 by 10 foot wind tunnel of the National Advisory Committee for Aeronautics

Description: This report presents a description of the 7 by 10 foot wind tunnel and associated apparatus of the National Advisory Committee for Aeronautics. Included also are calibration test results and characteristic test data of both static force tests and autorotation tests made in the tunnel.
Date: 1933
Creator: Harris, Thomas A

The 300 H.P. Benz Aircraft Engine

Description: This report provides a description of the Benz 300 H.P. aircraft engine containing 12 cylinders placed at a 60° angle. It includes a detailed description of the development of the constructional points, particularly the cylinders, pistons, and connecting rods, as well as the engine fitting, lubrication, oil pumps, bearings, oil tank, fuel pump, carburetors, and cooling system. There are seven pages of illustrative figures at the end of the report.
Date: January 1921
Creator: Heller, A.

The 1350 F stress-rupture properties of two wrought alloys and three cast alloys

Description: From Summary: "These properties compare favorably with those of the strongest similar alloys previously investigated. However, compared with a 60Cr-25Fe-15Mo alloy, the three cobalt-chronium-nickel cast alloys are inferior. A correlation of NACA and OSRD (Project NRC-8) data is presented, showing the variation of rupture strengths with temperature in the range of 1350^o to 2000^o for alloys."
Date: November 1947
Creator: Reynolds, E E; Freeman, J W & White, A E

The 1926 German seaplane contest

Description: The report discusses the problem of rating the various seaplane designs from the 1926 seaplane contest. The whole process of rating consists in measuring the climbing speed, flying weight and carrying capacity of a seaplane and then using these data as the basis of a construction problem.
Date: March 1928
Creator: Seewald, F; Blenk, H & Liebers, F

The 1929 Rhon soaring-flight contest

Description: The limitation of the 1929 contest to performance gliders necessitated the establishment of a formula which would make it possible to distinguish between performance gliders and school and training gliders. The sinking speed was therefore adopted as the basis for such a distinction, and the requirement was made that the sinking speed of a performance glider should not exceed 0.8 m/s. The rest of the report details the different entries with regard to design and performance.
Date: April 1930
Creator: Lippisch, Alexander

N.A.C.A. control position recorder

Description: Report discussing a new instrument is described which is capable of simultaneously recording the position of the three controls of an airplane. The records are taken photographically on a standard N.A.C.A. film drum and the instrument can be quickly installed in any airplane.
Date: May 1922
Creator: Norton, F. H.

N.A.C.A. Langley field wind tunnel apparatusthe tilting manometer

Description: A description is given of a tilting manometer designed to meet the requirements of a manometer for use in the wind tunnel at the Langley Memorial Aeronautical Laboratory. This gauge was designed to meet the requirements of a manometer in use in connection with a static pressure plate to indicate the wind speed in the tunnel. The requirements are noted. The sensitivity of the gauge must be made inversely proportional to the pressure to be measured. The gauge must be accurately and quickly set for any desired pressure. When set at the desired pressure, the extent of variation between the existing and the desired pressures may be readily estimated. In fact, this manometer is quick to adjust, is easy to read, always has the meniscus in the same position, and accurately indicates a large range of air speeds on what is a comparatively compact instrument.
Date: January 1921
Creator: Norton, F. H. & Bacon, D. L.

N.A.C.A. recording air speed meter

Description: A new type of air speed meter is described which was designed by the technical staff of the National Advisory Committee for Aeronautics. The instrument consists essentially of a tight metal diaphragm of high natural period which is acted upon by the pressure difference of a pitot-static head. The resulting deflection of this diaphragm is recorded optically on a moving film.
Date: October 1921
Creator: Norton, F. H.

N.A.C.A. Stall-Warning Device

Description: With some airplanes the approach to the stall is accompanied by changes in the behavior, such as tail buffeting or changes in the control characteristics of the airplane so that the pilot obtains a warning of the impending stall. Vith other airplanes it is possible to approach the stall without any perceptible warning other than the reading of the air-speed meter, in which case the danger of inadvertent stalling is considerably greater. Although it is not within the scope of this paper to discuss stalling characteristics, it is desired to point out that in general the danger of inadvertent stalling is greatest with those airplanes that behave worse when the stalling occurs; that is, with airplanes in which the stall starts at the wing tips. A warning of the impending stall is desirable in any case, but is particularly desirable with airplanes of the latter type.
Date: February 1938
Creator: Thompson, F. L.

The A.N.E.C. IV "Missel Thrush" light airplane

Description: A product of the Air Navigation Engineering Co., the Missel Thrush is a light airplane suitable for private ownership. It is a two seat tractor fuselage biplane with single I interplane struts designed by J. Bewsher.
Date: November 1926

The Aachen wind-tunnel balance

Description: Report discussing a description of the balance in the Aachen wind-tunnel.
Date: November 1934
Creator: Wieselsberger, C

Abacus giving the variation of the mean pressure of an aviation engine as a function of its speed of rotation

Description: Comparing the results of the calculations for computing the mean pressure of an aviation engine for any number of revolutions, with those of experiment, the writer, by numerous examples, shows the perfect agreement between them. This report will show that, by means of a special abacus, an engineer can instantly plot the characteristics of an engine.
Date: March 1921
Creator: Margoulis, W

Abnormal grain growth in M-252 and S-816 alloys

Description: Report discussing an experimental investigation was carried out on air- and vacuum-melted M-252 and S-816 alloys to find conditions of heating and hot-working which resulted in abnormal grain growth. The experiments were mainly limited to normal conditions of heating for hot-working and heat treatment and normal temperatures of solution treatment were used to allow grain growth after susceptibility to abnormal grain growth was developed by various experimental conditions. Results indicated that small reductions of essentially strain-free metal were the basic cause of such grain growth.
Date: November 1957
Creator: Decker, R F; Rush, A I; Dano, A G & Freeman, J W

Abnormal grain growth in nickel-base heat-resistant alloys

Description: From Introduction: "The data included in this report for Nimonic 80A alloy, for instance, represent experiments carried out to help clarify a production problem of grain-size control in an alloy which has been extensively used. The general procedure of the investigation was to carry out controlled laboratory experiments on samples of bar stock to find conditions of heating and hot-working which resulted in abnormal grain growth."
Date: December 1957
Creator: Decker, R F; Rush, A I; Dano, A G & Freeman, A G