UNT Libraries Government Documents Department - 23 Matching Results

Search Results

7-GeV Advanced Photon Source Instrumentation Initiative. Conceptual Design Report

Description: In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the next century. This new initiative will also include four user laboratory modules and a special laboratory designed to meet the x-ray imaging research needs of the users. The Conceptual Design Report (CDR) for the APS Instrumentation Initiative describes the scope of all the above technical and conventional construction and provides a detailed cost and schedule for these activities. According to these plans, this new initiative begins in FY 1994 and ends in FY 1998. The document also describes the preconstruction R & D plans for the Instrumentation Initiative activities and provides the cost estimates for the required R & D.
Date: October 1992
Creator: Argonne National Laboratory

Analytical Electron Microscopy Characterization of Uranium-Contaminated Soils from the Fernald Site, FY1993 Report

Description: A combination of optical microscopy, scanning electron microscopy with backscattered electron detection (SEM/BSE), and analytical electron microscopy (AEM) is being used to determine the nature of uranium in soils from the Fernald Environmental Management Project. The information gained from these studies is being used to develop and test remediation technologies. Investigations using SEM have shown that uranium is contained within particles that are typically 1 to 100 micrometers in diameter. Further analysis with AEM has shown that these uranium-rich regions are made up of discrete uranium-bearing phases. The distribution of these uranium phases was found to be inhomogeneous at the microscopic level.
Date: October 1994
Creator: Buck, E. C.; Cunnane, J. C.; Brown, N. R. & Dietz, N. L.

Comparison of Cast-in-Place Concrete Versus Precast Concrete Stay-in-Place Forming Systems for Lock Wall Rehabilitation

Description: "The objectives of this report are as follows: (a) To present the design and details utilized on the precast concrete panel rehabilitation at Troy Lock. (b) To compare the results of precast concrete panel rehabilitation with previous cast-in-place repairs, with respect to quality, cost, and schedule. (c) To recommend refinements in the details and methods of fabrication and erection of the precast panels, based on lessons learned from work performed at Troy Lock." (p. 2).
Date: October 1993
Creator: Miles, William R.

An Evaluation of Oocyte Size in Multiple Regressions Predicting Gonad Weight from Body Weight: a Test Using Hawaiian Ehu, Etelis carbunculus

Description: The following report is meant to evaluate whether the information on oocyte size improves ability to predict ovary weight from body weight, and we evaluate the cost-effectiveness of different sample sizes for characterizing egg size.
Date: October 1994
Creator: Lau, Boulderson B. & DeMartini, Edward E.

Fishery Interaction Between the Tuna Lonline and Other Pelagic Fisheries in Hawaii

Description: Abstract: The Hawaii pelagic surface fisheries and more recently the longline fisheries have grown dramatically. As a result, competition between fisheries on the fishing grounds and in the marketplace has also increased. Physical conflicts between vessels and claims of decreased fishing success by surface (troll and handline) fishermen led to the enactment of Federal regulations limiting the number of domestic longline vessels and the areas in which they can operate. The scientific evidence of biological or economic fishery interaction between longline and small-vessel fishermen is limited but suggests that intense longline fishing near the Hawaiian Islands has the potential to affect catch rates in other Hawaii fisheries. Better data collection and more research are needed to document fishery interaction and to improve fishery management.
Date: October 1993
Creator: Skillman, Robert A.; Boggs, Christofer H. & Pooley, Samuel G.

The Hawaiian Monk Seal on Laysan Island, 1987 and 1989

Description: This report is based on the findings from an observational study on the Hawaiian monk seal on Laysan Island in the Northwestern Hawaiian Islands during April 8 to July 20 1987 and March 30 to July 16 1989. The data collected focuses on haul-out, behavior, and reproductive patterns; population structure; and factors affecting survival.
Date: October 1994
Creator: Becker, Brenda L.; Ching, Patrick A.; Hiruki, Lisa M. & Zur, Steven A.

The Kewalo Research Facility: on the Forefront for More than 40 Years

Description: The following report provides extensive information on the Kewalo Research Facility of Oahu Island. The Kewalo Research Facility sits on Kewalo Basin and is the center for ongoing research programs designed to examine the most important environmental parameters on the behavior and physiology of tunas. Along with tuna the Kewalo Research facility is also a primary location to stage research activities associated with the studies and preservation of the Hawaiian monk seals, it also provides an important laboratory where research on and resuscitation of several threatened and endangered species of sea turtles found in the Pacific Ocean can be carried out.
Date: October 1999
Creator: Brill, Richard W.

Local Interfacial Area Concentration Measurement in Bubbly Flow

Description: The interfacial area concentration is one of the most important parameters in a thermal-hydraulic analysis of two-phase flow systems based on the two-fluid model. A theoretical foundation of the measurement method for the time averaged local interfacial area using a double sensor probe is presented. Based on this theory, the double sensor resistivity probe was employed for the measurement of local properties of two-phase flow such as the interfacial velocity, local interfacial area concentration and void fraction in vertical air-water bubbly flow. Experimental data are presented on the radial profiles of the void fraction, bubble velocity, bubble chord length and interfacial area concentration at various gas flow rates. In addition to these, some statistical information on turbulent motions of bubbles are presented. Each of the double sensors are checked against the global void measurement using a differential pressure. The result is very satisfactory. Furthermore, the area averaged void fraction, and the interfacial area concentration obtained from the double sensor probe measurement compared very well with the photographic measurements. The results show that the double sensor probe method is accurate and reliable for the local measurements of interfacial area and void fraction in bubbly two-phase flow. Results of the measurement of interfacial area concentration with the double sensor probe in forced flow loop are presented for bubbly flow at different liquid flow rates. The data indicate that the radial profiles of the interfacial area concentration show similar dependence on the liquid and gas flow rate like radial profiles of void fraction in the bubbly flow regime.
Date: October 1990
Creator: Ishii, M. & Revankar, Shripad T.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1990

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes technical progress of research and development efforts aimed at producing superconducting components based on the Y-Ba--Cu, Bi-Sr-Ca-Cu, Bi-Pb-Sr-Ca-Cu, and TI-Ba-Ca-Cu oxide systems including: synthesis and heat treatment of high-Ta superconductors, formation of monolithic and composite wires and tapes, superconductor/metal connectors, characterization of structures and superconducting and mechanical properties, and fabrication and properties of thin films.
Date: October 1990
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1991

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes technical progress of research and development efforts aimed at producing superconducting components based on the Y-Ba-Cu, BI-Sr-Ca-Cu, Bi-Pb-Sr-Ca-Cu, and TI-Ba-Ca-Cu oxide systems including: synthesis and heat treatment of high-Te superconductors, formation of monolithic and composite wires and tapes, superconductor/metal connectors, characterization of structures and superconducting and mechanical properties, and fabrication and properties of thin films.
Date: October 1991
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1992

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes the technical progress of research and development efforts aimed at producing superconducting components that are based on the Y-Ba-Cu, Bi-Sr-Ca-Cu, Bi-Pb-Sr-Ca-Cu, and (Tl,Pb)-(Ba,Sr)-Ca-Cu oxide systems including: synthesis and heat treatment of high-Ta superconductors, formation of monolithic and composite wires and tapes, superconductor/metal connectors, characterization of structures and superconducting and mechanical properties, fabrication and properties of thin films, and development of prototype components.
Date: October 1992
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1993

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes technical progress of research and development efforts aimed at producing superconducting components in the Y-Ba-Cu, (B1,Pb)-Sr-Ca-Cu, (Tl,Pb,BI)-(Ba,Sr)-Ca-Cu, and Hg-Ba-Ca-Cu-O oxide systems including: synthesis and heat treatment of high-Ta superconductors; formation of monolithic and composite wires, tapes, and coils; characterization of structures and superconducting and mechanical properties; fabrication and properties of films; and development of prototype components.
Date: October 1993
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1994

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes technical progress of research and development efforts aimed at producing superconducting components in the Y-Ba-Cu, (Bi,Pb)-Sr-Ca-Cu, (Tl,Pb,Bi)-(Ba,Sr)-Ca-Cu, and Hg-Ba-Ca-Cu-O oxide systems including: synthesis and heat treatment of high-Ta superconductors, formation of monolithic and composite conductors, characterization of structures and superconducting and mechanical properties, and fabrication and testing of prototype components.
Date: October 1994
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Practical Superconductor Development for Electrical Power Applications, Annual Report: 1995

Description: Annual report for the superconductor program at Argonne National Laboratory discussing the group's activities and research. This report describes the technical progress of research and development efforts aimed at producing superconducting components in the (Bi,Pb)-Sr-Ca-Cu, (T,Pb,Bi,V)- (Ba,Sr)-Ca-Cu, and Y-Ba-Cu oxide systems including: synthesis and heat treatment of high-Te superconductors, formation of monolithic and composite conductors, characterization of structures and superconducting and mechanical properties, and fabrication and testing of prototype components.
Date: October 1995
Creator: Argonne National Laboratory. Materials and Components Technology Division.

Programming in Fortran M Revision 1

Description: Fortran M is a small set of extensions to Fortran that supports a modular approach to the construction of sequential and parallel programs. Fortran M programs use channels to plug together processes which may be written in Fortran M or Fortran 77. Processes communicate by sending and receiving messages on channels. Channels and processes can be created dynamically, but programs remain deterministic unless specialized nondeterministic constructs are used. Fortran M programs can execute on a range of sequential, parallel, and networked computers. This report incorporates both a tutorial introduction to Fortran M and a users guide for the Fortran M compiler developed at Argonne National Laboratory. The Fortran M compiler, supporting software, and documentation are made available free of charge by Argonne National Laboratory, but are protected by a copyright which places certain restrictions on how they may be redistributed. See the software for details. The latest version of both the compiler and this manual can be obtained by anonymous ftp from Argonne National Laboratory in the directory pub/fortran-m at info.mcs.anl.gov.
Date: October 1993
Creator: Foster, Ian; Olson, Robert & Tuecke, Steven

Radiolytic and Radiolytically Induced Generation of Gases from Synthetic Wastes : Final Report

Description: To better understand the processes leading to the generation and release of gases from waste tanks, the authors studied the radiolytic and thermal generation of H2, N2O, N2, O2, and NH3 in nonradioactive waste simulant solutions and slurries. The radiolytic sources for H2 are e(sub aq)⁻ and its predecessors and H atoms. Radiolysis of the water generates some H2 and an additional amount comes from the hydrogen abstraction reaction H + RH(yields) H2+R(center_dot). Nitrate scavenges e(sub aq)(sup (minus) and its predecessors whereas nitrite is the major H-atom scavenger. Computer modeling shows that if [NO3⁻] is above 0.5 M, and [NO2⁻] is above 2M, the addition of other scavengers will have little effect on the yield of H2. In the presence of organic molecules O2 is efficiently destroyed. Small yields of ammonia were measured and the yields increase linearly with dose. The nitrogen in NH3 comes from organic chelators. The yields of gases in solution depend only weakly on temperature. The rate of thermal generation of gases increases upon preirradiation, reaches a maximum, and then declines. The known radiolytic degradation products of chelators, NTA, IDA, glycolate, glyoxylate, formaldehyde, formate, oxalate, and hydroxylainine were examined for their roles in the thermal generation of H2 and N2O at 60 C. In solution or slurry only radiolytically produced Pd intermediate strongly retains H2. Radiolytic yields of N2O are strongly reduced by Cr(III). In irradiated slurry, loose and tight gas were found. The loose gas could be removed by bubbling from the slurry, but the tight gas could be released only by dissolution of the slurry.
Date: October 1993
Creator: Meisel, Dan; Jonah, Charles D.; Kapoor, S.; Matheson, Max S. & Sauer, M. C.

Radiolytic and Thermal Generation of Gases from Hanford Grout Samples : Interim Report

Description: Gamma irradiation of WHC-supplied samples of grouted Tank 102-AP simulated nonradioactive waste has been carried out at three dose rates, 0.25, 0.63, and 130 krad/hr. The low dose rate corresponds to that in the actual grout vaults; with the high dose rate, doses equivalent to more than 40 years in the grout vault were achieved. An average G(H2) = 0.047 molecules/100 eV was found, independent of dose rate. The rate of H2 production decreases above 80 Mrad. For other gases, G(N2) = 0.12, G(O2) = 0.026, G(N2O) = 0.011 and G(CO) = 0.0042 at 130 krad/hr were determined. At lower dose rates, N2 and O2 could not be measured because of interference by trapped air. The value of G(H2) is higher than expected, suggesting segregation of water from nitrate and nitrite salts in the grout. The total pressure generated by the radiolysis at 130 krad/h has been independently measured, and total amounts of gases generated were calculated from this measurement. Good agreement between this measurement and the sum of all the gases that were independently determined was obtained. Therefore, the individual gas measurements account for most of the major components that are generated by the radiolysis. At 90 C, H2, N2, and N2O were generated at a rate that could be described by exponential formation of each of the gases. Gases measured at the lower temperatures were probably residual trapped gases. An as yet unknown product interfered with oxygen determinations at temperatures above ambient. The thermal results do not affect the radiolytic findings.
Date: October 1993
Creator: Meisel, Dan; Jonah, Charles D.; Kapoor, S.; Matheson, Max S. & Mulac, W. A.

Research in Mathematics and Computer Science: March 1, 1991 - September 30, 1992

Description: This report discusses the following topics in mathematics and computer science at Argonne National Laboratory: Harnessing the Power; Modeling Piezoelectric Crystals; A Two-Way Street; The Challenge Is On; A True Molecular Engineering Capability; CHAMMPions Attack Climate Issues; Studying Vortex Dynamics; Studying Vortex Structure; Providing Reliable and Fast Derivatives; Automating Reasoning for Scientific Problem Solving; Optimization and Mathematical Programming; Scalable Algorithms for Linear Algebra; Reliable Core Software; Computing Phylogenetic Trees; Managing Life-Critical Systems; Interacting with Data through Visualization; New Tools for New Technologies.
Date: October 1992
Creator: Pieper, Gail W.

Test and Evaluation of the Argonne BPAC10 Series Air Chamber Calorimeter Designed for 20 Minute Measurements

Description: This paper is the final report on DOE-OSS Task ANLE88002 Fast Air Chamber Calorimetry.'' The task objective was to design, construct, and test an isothermal air chamber calorimeter for plutonium assay of bulk samples that would meet the following requirements for sample power measurement: average sample measurement time less than 20 minutes. Measurement of samples with power output up to 10 W. Precision of better than 1% RSD for sample power greater than 1 W. Precision better than 0.010 watt SD, for sample power less than 1 W. This report gives a description of the calorimeter hardware and software and discusses the test results. The instrument operating procedure, included as an appendix, gives examples of typical input/output and explains the menu driven software.
Date: October 1990
Creator: Perry, Ronald B.; Fiarman, Sidney; Jung, Erwin A. & Cremers, Teresa

VARIANT: VARIational Anisotropic Nodal Transport for Multidimensional Cartesian and Hexagonal Geometry Calculation

Description: The theoretical basis, implementation information and numerical results are presented for VARIANT (VARIational Anisotropic Neutron Transport), a FORTRAN module of the DIF3D code system at Argonne National Laboratory. VARIANT employs the variational nodal method to solve multigroup steady-state neutron diffusion and transport problems. The variational nodal method is a hybrid finite element method that guarantees nodal balance and permits spatial refinement through the use of hierarchical complete polynomial trial functions. Angular variables are expanded with complete or simplified P₁, P₃ or P₅5 spherical harmonics approximations with full anisotropic scattering capability. Nodal response matrices are obtained, and the within-group equations are solved by red-black or four-color iteration, accelerated by a partitioned matrix algorithm. Fission source and upscatter iterations strategies follow those of DIF3D. Two- and three-dimensional Cartesian and hexagonal geometries are implemented. Forward and adjoint eigenvalue, fixed source, gamma heating, and criticality (concentration) search problems may be performed.
Date: October 1995
Creator: Palmiotti, G.; Lewis, E. E. & Carrico, C. B.