UNT Libraries - 47 Matching Results

Search Results

Results: 1 - 24 next
open access

Characterization of Boron Nitride Thin Films on Silicon (100) Wafer.

Description: Cubic boron nitride (cBN) thin films offer attractive mechanical and electrical properties. The synthesis of cBN films have been deposited using both physical and chemical vapor deposition methods, which generate internal residual, stresses that result in delamination of the film from substrates. Boron nitride films were deposited using electron beam evaporation without bias voltage and nitrogen bombardment (to reduce stresses) were characterize using FTIR, XRD, SEM, EDS, TEM, and AFM technique… more
Date: August 2007
Creator: Maranon, Walter
Item Type: Refine your search to only Thesis or Dissertation
open access

A Computer-Based Process Control System for a Target Station in a LINAC Facility

Description: An event-driven, sequential, process control system was designed for International Isotopes, Inc., to automate and remotely control a target station at the company's linear accelerator facility. The designed system consisted of two major sections: a software program (virtual instrument), which was developed by LabVIEW, and a hardware interface (FieldPoint Modular Distributed I/O System by National Instrument), which had to be a pre-developed system that did not require customization. The design… more
Date: May 1999
Creator: Al-Shantaf, Abdulraouf O.
Item Type: Refine your search to only Thesis or Dissertation
open access

Computer Virus Spread Containment Using Feedback Control.

Description: In this research, a security architecture based on the feedback control theory has been proposed. The first loop has been designed, developed and tested. The architecture proposes a feedback model with many controllers located at different stages of network. The controller at each stage gives feedback to the one at higher level and a decision about network security is taken. The first loop implemented in this thesis detects one important anomaly of virus attack, rate of outgoing connection. Tho… more
Date: December 2004
Creator: Yelimeli Guruprasad, Arun
Item Type: Refine your search to only Thesis or Dissertation
open access

Cost Savings Realized Through Proper Sizing of an Excessive Instrument Air System.

Description: The purpose of this research was to determine if installing a smaller air compressor could reduce the electrical usage of a large semiconductor manufacturing plant. A 200 horsepower Atlas Copco compressor was installed with the existing 500 horsepower Ingersoll-Rand compressors. Testing was conducted during the regular manufacturing process at MEMC Southwest in Sherman, Texas. Analysis of the data found that installing the new compressor could reduce electrical consumption. The study also found… more
Date: December 2003
Creator: Condron, Ewell D.
Item Type: Refine your search to only Thesis or Dissertation
open access

A Data Acquisition System Experiment for Gas Temperature and Pressure Measurements on a Liquid-Nitrogen-Powered Vehicle

Description: A data acquisition system was set up to measure gas temperatures and pressures at various points on a liquid-nitrogen-powered vehicle. The experiment was attempted to develop a data acquisition method for applications on engines that use liquid air as the fuel. Two thermocouples and a pressure transducer were connected using data acquisition instruments interfaced to a laptop computer to acquire data.
Date: May 1998
Creator: Lui, Samson Sze-Sang
Item Type: Refine your search to only Thesis or Dissertation
open access

The Design and Development of Lightweight Composite Wall, Roof, and Floor Panels for Rigid Wall Shelter

Description: This thesis presents a research effort aimed at developing a stronger, lighter, and more economic shelter using rigid wall panels. Reported herein is insulation research, wall and roof panel design and testing, floor section modeling and strength calculations, and cost and weight calculations. Beginning stages focus on developing solid wall and roof panels using cold-formed steel corrugated sheathing and members, as well as polyurethane spray foam for insulation. This research includes calculat… more
Date: May 2018
Creator: Artman, Jeremy J
Item Type: Refine your search to only Thesis or Dissertation

Design Method for Cold-Formed Steel Shear Wall Sheathed with Polymer Composite Panel

Description: In order to predict the strength of shear wall with cold-formed steel framing members, analytical models were reviewed. Multiple analytical models were studied, as well as twenty-one connection tests were performed. The connection tests consist of 50-ksi cold-formed steel framing track, different fastening configurations, and different sheathing thicknesses (1/8" and 1/2"). No.12 screw resulted in the highest peak load of all fastening configurations, while the rivet connection had the lowest p… more
Date: August 2020
Creator: Dewaidi, Mohaned Ali
Item Type: Refine your search to only Thesis or Dissertation
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
open access

Design of a Monitoring System for a Plasma Cleaning Machine

Description: Plasma cleaning is the most effective dry process to remove surface contaminates from a SAW (Surface Acoustical Wave) device. Consistent gas pressures, flows, and good electrical connections between the chamber shelves are necessary for the process to function predictably. In addition, operation of the monitoring system must be transparent to the plasma cleaning unit. This thesis describes a simple solution to the complex problem of monitoring a plasma cleaning system. The monitoring system use… more
Date: May 1999
Creator: Fooks, Terry M. (Terry Max)
Item Type: Refine your search to only Thesis or Dissertation
open access

Determination of the Shelf Life of Aluminum Electrolytic Capacitors.

Description: The aluminum electrolytic capacitor is used extensively in the electric utility industry. A factor limiting the storage of spare capacitors is the integrity of the aluminum oxide dielectric, which over time breaks down contributing to a shelf life currently estimated at one nuclear power electric generating station to be approximately five years. This project examined the electrical characteristics of naturally aged capacitors of several different styles to determine if design parameters were… more
Date: May 2002
Creator: Wynne, Edward McFaddin
Item Type: Refine your search to only Thesis or Dissertation
open access

Development of a Simplified Fracture Toughness Tool for Polymers

Description: This thesis presents research toward the development of a simple inexpensive fracture toughness tool for polymeric materials. Experiments were conducted to test the specimen configuration and the fracture toughness tool against an established ASTM standard for polymer fracture toughness, D5045, and a commonly used four-point bend method. The materials used in this study were polycarbonate and high density polyethylene. Reductions in both the production time and the variability resulting from th… more
Date: August 1997
Creator: Marnock, Patrick J. (Patrick Joseph)
Item Type: Refine your search to only Thesis or Dissertation
open access

Effect of Amines as Corrosion Inhibitors for a Low Carbon Steel in Power Industry

Description: Commonly used amines in power industry, including morpholine, DBU (1,8-diazabicyclo[5.4.0]undec-7-ene), and DMA (dimethylallylamine) were evaluated for their effect on AISI 1018 steel at 250oF. Samples were exposed to an autoclave containing amine added aqueous solution at pH of 9.5 for 1, 2, 4, 6, 8, and 12 hours. Morphology studies were carried using scanning electron microscope (SEM), phase analysis was done utilizing Fourier transform infrared spectroscopy (FTIR), and weight loss was perfor… more
Date: December 2004
Creator: Díaz, Jorge G.
Item Type: Refine your search to only Thesis or Dissertation
open access

Effects of a Surface Engineered Metallic Coating on Elastomeric Valve Stem Seal Leakage

Description: Valve stem seal leakage is a major source of fugitive emissions, and controlling these emissions can result in added expense in leak detection and repair programs. Elastomeric O-rings can be used as valve stem seals, and O-ring manufacturers recommend lubrication of elastomeric seals to prevent damage and to assure proper sealing. In this research, a metallic coating was applied as a lubricant using a vacuum vapor deposition process to the surface of elastomeric valve stem seals. Valve stem le… more
Date: December 2000
Creator: Taylor, John Abner
Item Type: Refine your search to only Thesis or Dissertation
open access

Fabrication and Testing of Biomimetic Microstructures for Walkway Tribometers

Description: The main objective of this work is to give contribution in both additive manufacturing (AM) and tribometry derived from the application and study of materials available with the use of biomimetic designs. Additional contributions are determining what effects treatments for flooring surfaces may have on the dynamic coefficient of friction and the effects of these products on common surfaces. The validity of the proposed methodology for a proof of concept was demonstrated by comparing measured dy… more
Date: December 2019
Creator: Haney, Christopher Willard
Item Type: Refine your search to only Thesis or Dissertation

Fabrication and Testing of Polymeric Flexible Sheets with Asymmetric Distributed Magnetic Particles for Biomedical Actuated Devices

Description: This thesis explores a method to fabricate magnetic membranes with asymmetric distribution of particles and their testing as actuators. Focus of this research is to fabricate thin polymeric sheets and thickness range of 120-125µm, with asymmetric distribution of magnetic nano particles, employing micromagnets during the fabrication. The micromagnets are used to localize the magnetic particles during the curing process at selected locations. The effect of the asymmetric distribution of magnetic … more
Date: May 2022
Creator: Bakaraju, Megha Ramya
Item Type: Refine your search to only Thesis or Dissertation
open access

FEM of nanoindentation on micro- and nanocrystalline Ni: Analysis of factors affecting hardness and modulus values.

Description: Nanoindentation is a widely used technique to measure the mechanical properties of films with thickness ranging from nanometers to micrometers. A much better understanding of the contact mechanics is obtained mostly through finite element modeling. The experiments were modeled using the software package Nano SP1 that is based on COSMOSM™ (Structural Research & Analysis Corp, www.cosmosm.com), a finite element code. The fundamental material properties affecting pile-up are the ratio of the effec… more
Date: August 2005
Creator: Pothapragada, Raja Mahesh
Item Type: Refine your search to only Thesis or Dissertation
open access

Flow Accelerated Corrosion Experience at Comanche Peak Steam Electric Station

Description: Flow accelerated corrosion (FAC) is a major concern in the power industry as it causes thinning of the pipes by the dissolution of the passive oxide layer formed on the pipe surface. Present research deals with comparing the protection offered by the magnetite (Fe3O4) versus maghemite (γ-Fe2O3) phases thickness loss measurements. Fourier transform infrared spectroscopy (FTIR) is used in distinguishing these two elusive phases of iron oxides. Representative pipes are collected from high pressure… more
Date: May 2008
Creator: Nakka, Ravi Kumar
Item Type: Refine your search to only Thesis or Dissertation
open access

FPGA Prototyping of a Watermarking Algorithm for MPEG-4

Description: In the immediate future, multimedia product distribution through the Internet will become main stream. However, it can also have the side effect of unauthorized duplication and distribution of multimedia products. That effect could be a critical challenge to the legal ownership of copyright and intellectual property. Many schemes have been proposed to address these issues; one is digital watermarking which is appropriate for image and video copyright protection. Videos distributed via the Inter… more
Date: May 2007
Creator: Cai, Wei
Item Type: Refine your search to only Thesis or Dissertation
open access

Fracture Toughness Testing of Plastics under Various Environmental Conditions

Description: The primary objective of this study is to test the applicability to plastics of a fracture toughness testing tool developed for metals. The intent is to study pre-test conditioning of several plastic materials and the effect of the depth of the razor notch cut in the chevron notched fracture toughness test specimens. The study includes the careful preparation of samples followed by conditioning in various environments. Samples were subjected to laboratory air for a specific duration or to a con… more
Date: December 1997
Creator: Velpuri, Seshagirirao V.
Item Type: Refine your search to only Thesis or Dissertation
open access

Hydrophobicity of Magnetite Coating on Low Carbon Steel

Description: Superhydrophobic coatings (SHC) with excellent self-cleaning and corrosion resistance property is developed on magnetite coated AISI SAE 1020 steel by using a simple immersion method. Roughness measurement, scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), contact angle measurement (CAM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), potentiodynamic polarization test, electrochemical impedance spectroscopy (EIS), … more
Date: August 2018
Creator: Akhtar, Mst Alpona
Item Type: Refine your search to only Thesis or Dissertation
open access

Indoor Propagation Modeling at 2.4 GHz for IEEE 802.11 Networks

Description: Indoor use of wireless systems poses one of the biggest design challenges. It is difficult to predict the propagation of a radio frequency wave in an indoor environment. To assist in deploying the above systems, characterization of the indoor radio propagation channel is essential. The contributions of this work are two-folds. First, in order to build a model, extensive field strength measurements are carried out inside two different buildings. Then, path loss exponents from log-distance path l… more
Date: December 2005
Creator: Tummala, Dinesh
Item Type: Refine your search to only Thesis or Dissertation
open access

Investigation of Immersion Cooled ARM-Based Computer Clusters for Low-Cost, High-Performance Computing

Description: This study aimed to investigate performance of ARM-based computer clusters using two-phase immersion cooling approach, and demonstrate its potential benefits over the air-based natural and forced convection approaches. ARM-based clusters were created using Raspberry Pi model 2 and 3, a commodity-level, single-board computer. Immersion cooling mode utilized two types of dielectric liquids, HFE-7000 and HFE-7100. Experiments involved running benchmarking tests Sysbench high performance linpack (H… more
Date: August 2017
Creator: Mohammed, Awaizulla Shareef
Item Type: Refine your search to only Thesis or Dissertation
open access

Investigation of Spray Cooling Schemes for Dynamic Thermal Management

Description: This study aims to investigate variable flow and intermittent flow spray cooling characteristics for efficiency improvement in active two-phase thermal management systems. Variable flow spray cooling scheme requires control of pump input voltage (or speed), while intermittent flow spray cooling scheme requires control of solenoid valve duty cycle and frequency. Several testing scenarios representing dynamic heat load conditions are implemented to characterize the overall performance of variable… more
Date: May 2017
Creator: Yata, Vishnu Vardhan Reddy
Item Type: Refine your search to only Thesis or Dissertation
open access

Investigation of the feasibility of non-invasive carbon dioxide detection using spectroscopy in the visible spectrum.

Description: Pulse oximeters are used in operating rooms and recovery rooms as a monitoring device for oxygen in the respiratory system of the patient. The advantage of pulse oximeters over other methods of oxygen monitoring is that they are easy to use and they are non-invasive, which means it is not necessary break the skin to extract blood for information to be obtained. The standard for the measurement of partial pressure of CO2 and O2 is an arterial blood gas analysis (ABG). However routine monitoring … more
Date: December 2007
Creator: Marks, Damian
Item Type: Refine your search to only Thesis or Dissertation
Back to Top of Screen