UNT Theses and Dissertations - 90 Matching Results

Search Results

A Preliminary Controller Design for Drone Carried Directional Communication System

Description: In this thesis, we conduct a preliminary study on the controller design for directional antenna devices carried by drones. The goal of the control system is to ensure the best alignment between two directional antennas so as to enhance the performance of air-to-air communication between the drones. The control system at the current stage relies on the information received from GPS devices. The control system includes two loops: velocity loop and position loop to suppress wind disturbances and to assure the alignment of two directional antennae. The simulation and animation of directional antennae alignment control for two-randomly moving drones was developed using SIMULINK. To facilitate RSSI-based antenna alignment control to be conducted in the future work, a study on initial scanning techniques is also included at the end of this thesis.
Date: August 2015
Creator: AL-Emrani, Firas
Partner: UNT Libraries

Practical Evaluation of a Software Defined Cellular Network

Description: This thesis proposes a design of a rapidly deployable cellular network prototype that provides voice and data communications and it is interoperable with legacy devices and the existing network infrastructure. The prototype is based on software defined radio and makes use of IEEE 802.11 unlicensed wireless radio frequency (RF) band for backhaul link and an open source GSM implementation software. The prototype is also evaluated in environments where there is limited control of the radio frequency landscape, and using Voice Over Internet Protocol (VoIP) performance metrics to measure the quality of service. It is observed that in environments where the IEEE 802.11 band is not heavily utilized, a large number of calls are supported with good quality of service. However, when this band is heavily utilized only a few calls can be supported as the quality of service rapidly degrades with increasing number of calls, which is due to interference. It is concluded that in order to achieve tolerable voice quality, unused licensed spectrum is needed for backhaul communication between base stations.
Date: May 2017
Creator: Agbogidi, Oghenetega
Partner: UNT Libraries

Low Leakage Asymmetric Stacked Sram Cell

Description: Memory is an important part of any digital processing system. On-chip SRAM can be found in various levels of the memory hierarchy in a processor and occupies a considerable area of the chip. Leakage is one of the challenges which shrinking of technology has introduced and the leakage of SRAM constitutes a substantial part of the total leakage power of the chip due to its large area and the fact that many of the cells are idle without any access. In this thesis, we introduce asymmetric SRAM cells using stacked transistors which reduce the leakage up to 26% while increasing the delay of the cell by only 1.2% while reducing the read noise margin of the cell by only 15.7%. We also investigate an asymmetric cell configuration in which increases the delay by 33% while reduces the leakage up to 30% and reducing the read noise margin by only 1.2% compared to a regular SRAM cell.
Date: May 2014
Creator: Ahrabi, Nina
Partner: UNT Libraries

Consensus Building in Sensor Networks and Long Term Planning for the National Airspace System

Description: In this thesis, I present my study on the impact of multi-group network structure on the performance of consensus building strategies, and the preliminary mathematical formulation of the problem on improving the performance of the National Airspace system (NAS) through long-term investment. The first part of the thesis is concerned with a structural approach to the consensus building problem in multi-group distributed sensor networks (DSNs) that can be represented by bipartite graph. Direct inference of the convergence behavior of consensus strategies from multi-group DSN structure is one of the contributions of this thesis. The insights gained from the analysis facilitate the design and development of DSNs that meet specific performance criteria. The other part of the thesis is concerned with long-term planning and development of the NAS at a network level, by formulating the planning problem as a resource allocation problem for a flow network. The network-level model viewpoint on NAS planning and development will give insight to the structure of future NAS and will allow evaluation of various paradigms for the planning problem.
Date: May 2011
Creator: Akula, Naga Venkata Swathik
Partner: UNT Libraries

A Study of Mobility Models based on Spatial Node Distribution and Area Coverage

Description: Mobile wireless sensor networks are not widely implemented in the real world, even after years of research carried out in this field. One reason is the lack of understanding of the impact that mobility has on network performance. The simulation and emulation of mobile wireless sensor networks is necessary before they are deployed for the real-world applications. This thesis presents a simulation-based study of different mobility models. The total area coverage that depends on the pattern of node movements is observed through simulations. The spatial distribution of node locations is also studied. Various synthetic mobility models available are explored based on their theoretical descriptions. ‘BonnMotion' is used as the network simulator for investigating different mobility scenarios. The results obtained after simulations are imported to MATLAB and the analysis of node movements is done through various plots and inferences from the data. The comparison of mobility models is also discussed based on their spatial node distribution in the simulated scenarios.
Date: May 2017
Creator: Alla, Sindhu
Partner: UNT Libraries

Improving the Gameplay Experience and Guiding Bottom Players in an Interactive Mapping Game

Description: In game based learning, motivating the players to learn by providing them a desirable gameplay experience is extremely important. However, it's not an easy task considering the quality of today's commercial non-educational games. Throughout the gameplay, the player should neither get overwhelmed nor under-challenged. The best way to do so is to monitor the player's actions in the game because these actions can tell the reason behind the player's performance. They can also tell about the player's lacking competencies or knowledge. Based on this information, in-game educational interventions in the form of hints can be provided to the player. The success of such games depends on their interactivity, motivational outlook and thus player retention. UNTANGLED is an online mapping game based on crowd-sourcing, developed by Reconfigurable Computing Lab, UNT for the mapping problem of CGRAs. It is also an educational game for teaching the concepts of reconfigurable computing. This thesis performs qualitative comparative analysis on gameplays of low performing players of UNTANGLED. And the implications of this analysis are used to provide recommendations for improving the gameplay experience for these players by guiding them. The recommendations include strategies to reach a high score and a compact solution, hints in the form of preset patterns and a clustering based approach.
Access: This item is restricted to UNT Community Members. Login required if off-campus.
Date: May 2017
Creator: Ambekar, Kiran
Partner: UNT Libraries

An investigation into graph isomorphism based zero-knowledge proofs.

Description: Zero-knowledge proofs protocols are effective interactive methods to prove a node's identity without disclosing any additional information other than the veracity of the proof. They are implementable in several ways. In this thesis, I investigate the graph isomorphism based zero-knowledge proofs protocol. My experiments and analyses suggest that graph isomorphism can easily be solved for many types of graphs and hence is not an ideal solution for implementing ZKP.
Date: December 2009
Creator: Ayeh, Eric
Partner: UNT Libraries

An Interactive Framework for Teaching Fundamentals of Digital Logic Design and VLSI Design

Description: Integrated Circuits (ICs) have a broad range of applications in healthcare, military, consumer electronics etc. The acronym VLSI stands for Very Large Scale Integration and is a process of making ICs by placing millions of transistors on a single chip. Because of advancements in VLSI design technologies, ICs are getting smaller, faster in speed and more efficient, making personal devices handy, and with more features. In this thesis work an interactive framework is designed in which the fundamental concepts of digital logic design and VLSI design such as logic gates, MOS transistors, combinational and sequential logic circuits, and memory are presented in a simple, interactive and user friendly way to create interest in students towards engineering fields, especially Electrical Engineering and Computer Engineering. Most of the concepts are explained in this framework by taking the examples which we see in our daily lives. Some of the critical design concerns such as power and performance are presented in an interactive way to make sure that students can understand these significant concepts in an easy and user friendly way.
Date: August 2014
Creator: Battina, Brahmasree
Partner: UNT Libraries

A Cognitive Radio Application through Opportunistic Spectrum Access

Description: In wireless communication systems, one of the most important resources being focused on all the researchers is spectrum. A cognitive radio (CR) system is one of the efficient ways to access the radio spectrum opportunistically, and efficiently use the available underutilized licensed spectrum. Spectrum utilization can be significantly enhanced by developing more applications with adopting CR technology. CR systems are implemented using a radio technology called software-defined radios (SDR). SDR provides a flexible and cost-effective solution to fulfil the requirements of end users. We can see a lot of innovations in Internet of Things (IoT) and increasing number of smart devices. Hence, a CR system application involving an IoT device is studied in this thesis. Opportunistic spectrum access involves two tasks of CR system: spectrum sensing and dynamic spectrum access. The functioning of the CR system is rest upon the spectrum sensing. There are different spectrum sensing techniques used to detect the spectrum holes and a few of them are discussed here in this thesis. The simplest and easiest to implement energy detection spectrum sensing technique is used here to implement the CR system. Dynamic spectrum access involves different models and strategies to access the spectrum. Amongst the available models, an interweave model is more challenging and is used in this thesis. Interweave model needs effective spectrum sensing before accessing the spectrum opportunistically. The system designed and simulated in this thesis is capable of transmitting an output from an IoT device using USRP and GNU radio through accessing the radio spectrum opportunistically.
Date: May 2017
Creator: Bhadane, Kunal Ashok Ashok
Partner: UNT Libraries

Investigation of the Effect of Functional Units/Connectivity Arrangement on Energy Consumption of Reconfigurable Architectures Using an Interactive Design Framework

Description: Allocation of expensive resources, (such as Multiplier) onto the CGRA has been of interest from quite some time. For these architectural solutions to fulfill the designers' requirements, it is of utmost importance that the design offers high performance, low power consumption, and effective area utilization. The allocation problem is studied using the UntangledII gaming environment, which has been developed at the Reconfigurable Computing Lab at UNT to discover the design of custom domain-specific architectures. This thesis explores several case-studies to investigate the arrangement of functional units and interconnects to achieve a low power, high performance, and flexible heterogeneous designs that can fit for a suite of applications. In the later part, several human mapping strategies of top and bottom players to design a custom domain-specific architecture are presented. Some common trends that were examined while analyzing the mapping strategies of the players are also discussed.
Date: August 2017
Creator: Bhargava, Arpita
Partner: UNT Libraries

Development of Wireless Sensor Network System for Indoor Air Quality Monitoring

Description: This thesis describes development of low cost indoor air quality (IAQ) monitoring system for research. It describes data collection of various parameters concentration present in indoor air and sends data back to host PC for further processing. Thesis gives detailed information about hardware and software implementation of IAQ monitoring system. Also discussed are building wireless ZigBee network, creating user friendly graphical user interface (GUI) and analysis of obtained results in comparison with professional benchmark system to check system reliability. Throughputs obtained are efficient enough to use system as a reliable IAQ monitor.
Date: December 2012
Creator: Borkar, Chirag
Partner: UNT Libraries

A Real-Time Electronic Sound Analysis System with Graphical User Interface

Description: Noise-induced hearing loss is a serious problem common to musical environments. Current dosimetry technology is primarily designed for industrial environments and not suited for musical settings. At present, there are no government regulations that apply to the educational music environment as it relates to monitoring and prevention of hearing loss. Also, no system exists than can serve as a proactive tool in observation and reporting of sound exposure levels with the goal of hearing conservation. Newly proposed system takes a software based approach in designing a proactive dosimetry system that can assess the risk of sound noise exposure. It provides real-time feedback trough a graphical user interface that is capable of database storage for further study.
Date: August 2011
Creator: Brgulja, Amir
Partner: UNT Libraries

An Arduino Based Control System for a Brackish Water Desalination Plant

Description: Water scarcity for agriculture is one of the most important challenges to improve food security worldwide. In this thesis we study the potential to develop a low-cost controller for a small scale brackish desalination plant that consists of proven water treatment technologies, reverse osmosis, cation exchange, and nanofiltration to treat groundwater into two final products: drinking water and irrigation water. The plant is powered by a combination of wind and solar power systems. The low-cost controller uses Arduino Mega, and Arduino DUE, which consist of ATmega2560 and Atmel SAM3X8E ARM Cortex-M3 CPU microcontrollers. These are widely used systems characterized for good performance and low cost. However, Arduino also requires drivers and interfaces to allow the control and monitoring of sensors and actuators. The thesis explains the process, as well as the hardware and software implemented.
Date: August 2015
Creator: Caraballo, Ginna
Partner: UNT Libraries

Communication System over Gnu Radio and OSSIE

Description: GNU Radio and OSSIE (Open-Source SCA (Software communication architecture) Implementation-Embedded) are two open source software toolkits for SDR (Software Defined Radio) developments, both of them can be supported by USRP (Universal Software Radio Peripheral). In order to compare the performance of these two toolkits, an FM receiver over GNU Radio and OSSIE are tested in my thesis, test results are showed in Chapter 4 and Chapter 5. Results showed that the FM receiver over GNU Radio has better performance, due to the OSSIE is lack of synchronization between USRP interface and the modulation /demodulation components. Based on this, the SISO (Single Input Single Output) communication system over GNU Radio is designed to transmit and receive sound or image files between two USRP equipped with RFX2400 transceiver at 2.45G frequency. Now, GNU Radio and OSSIE are widely used for academic research, but the future work based on GNU Radio and OSSIE can be designed to support MIMO, sensor network, and real time users etc.
Date: December 2011
Creator: Cheng, Zizhi
Partner: UNT Libraries

Measurement and Analysis of Indoor Air Quality Conditions

Description: More than 80% of the people in urban regions and about 98% of cities in low and middle income countries have poor air quality according to the World Health Organization. People living in such environment suffer from many disorders like a headache, shortness of breath or even the worst diseases like lung cancer, asthma etc. The main objective of the thesis is to create awareness about the air quality and the factors that are causing air pollution to the people which is really important and provide tools at their convenience to measure and analyze the air quality. Taking real time air quality scenarios, various experiments were made using efficient sensors to study both the indoor and outdoor air quality. These experimental results will eventually help people to understand air quality better. An outdoor air quality data measurement system is developed in this research using Python programming to provide people an opportunity to retrieve and manage the air quality data and get the concentrations of the leading pollutants. The entire designing of the program is made to run with the help of a graphical user interface tool for the user, as user convenience is considered as one of the objectives of the thesis. A graphical user interface is made for the user convenience to visualize graphically the data from the database. The designed system is tested and used for the measurement and analysis of the outdoor air quality. This data will be available in the database so it can be used for analyzing the air quality data for several days or months or years. Using the GrayWolf system and the designed outdoor air quality data measurement system, both the indoor and outdoor air quality was measured to analyze and correlate.
Date: August 2016
Creator: Chidurala, Veena
Partner: UNT Libraries

Parameter Estimation Using Consensus Building Strategies with Application to Sensor Networks

Description: Sensor network plays a significant role in determining the performance of network inference tasks. A wireless sensor network with a large number of sensor nodes can be used as an effective tool for gathering data in various situations. One of the major issues in WSN is developing an efficient protocol which has a significant impact on the convergence of the network. Parameter estimation is one of the most important applications of sensor network. In order to model such large and complex networks for estimation, efficient strategies and algorithms which take less time to converge are being developed. To deal with this challenge, an approach of having multilayer network structure to estimate parameter and reach convergence in less time is estimated by comparing it with known gossip distributed algorithm. Approached Multicast multilayer algorithm on a network structure of Gaussian mixture model with two components to estimate parameters were compared and simulated with gossip algorithm. Both the algorithms were compared based on the number of iterations the algorithms took to reach convergence by using Expectation Maximization Algorithm.Finally a series of theoretical and practical results that explicitly showed that Multicast works better than gossip in large and complex networks for estimation in consensus building strategies.
Date: December 2013
Creator: Dasgupta, Kaushani
Partner: UNT Libraries

A Low-cost Wireless Sensor Network System Using Raspberry Pi and Arduino for Environmental Monitoring Applications

Description: Sensors are used to convert physical quantity into numerical data. Various types of sensors can be coupled together to make a single node. A distributed array of these nodes can be deployed to collect environmental data by using appropriate sensors. Application of low powered short range radio transceivers as a communication medium between spatially distributed sensor nodes is known as wireless sensor network. In this thesis I build such a network by using Arduino, Raspberry Pi and XBee. My goal was to accomplish a prototype system so that the collected data can be stored and managed both from local and remote locations. The system was targeted for both indoor and outdoor environment. As a part of the development a controlling application was developed to manage the sensor nodes, wireless transmission, to collect and store data using a database management service. Raspberry Pi was used as base station and webserver. Few web based application was developed for configuring the network, real time monitoring, and database management. Whole system functions as a single entity. The use of open source hardware and software made it possible to keep the cost of the system low. The successful development of the system can be considered as a prototype which needs to be expanded for large scale environmental monitoring applications.
Date: May 2014
Creator: Ferdoush, Sheikh Mohammad
Partner: UNT Libraries

Development of Indium Oxide Nanowires as Efficient Gas Sensors

Description: Crystalline indium oxide nanowires were synthesized following optimization of growth parameters. Oxygen vacancies were found to impact the optical and electronic properties of the as-grown nanowires. Photoluminescence measurements showed a strong U.V emission peak at 3.18 eV and defect peaks in the visible region at 2.85 eV, 2.66 eV and 2.5 eV. The defect peaks are attributed to neutral and charged states of oxygen vacancies. Post-growth annealing in oxygen environment and passivation with sulphur are shown to be effective in reducing the intensity of the defect induced emission. The as-grown nanowires connected in an FET type of configuration shows n-type conductivity. A single indium oxide nanowire with ohmic contacts was found to be sensitive to gas molecules adsorbed on its surface.
Date: December 2011
Creator: Gali, Pradeep
Partner: UNT Libraries

Design and Implementation of Communication Platform for Autonomous Decentralized Systems

Description: This thesis deals with the decentralized autonomous system, in which individual nodes acting like peers, communicate and participate in collaborative tasks and decision making processes. An experimental test-bed is created using four Garcia robots. The robots act like peers and interact with each other using user datagram protocol (UDP) messages. Each robot continuously monitors for messages coming from other robots and respond accordingly. Each robot broadcasts its location to all the other robots within its vicinity. Robots do not have built-in global positioning system (GPS). So, an indoor localization method based on signal strength is developed to estimate robot's position. The signal strength that the robot gets from the nearby wireless access points is used to calculate the robot's position. Trilateration and fingerprint are some of the indoor localization methods used for this purpose. The communication functionality of the decentralized system has been tested and verified in the autonomous systems laboratory.
Date: December 2010
Creator: Gottipati, Naga Sravani
Partner: UNT Libraries

Practical Robust MIMO OFDM Communication System for High-Speed Mobile Communication

Description: This thesis presents the design of a communication system (PRCS) which improves on all aspects of the current state of the art 4G communication system Long Term Evolution (LTE) including peak to average power ratio (PAPR), data reliability, spectral efficiency and complexity using the most recent state of the art research in the field combined with novel implementations. This research is relevant and important to the field of electrical and communication engineering because it provides benefits to consumers in the form of more reliable data with higher speeds as well as a reduced burden on hardware original equipment manufacturers (OEMs). The results presented herein show up to a 3 dB reduction in PAPR, less than 10-5 bit errors at 7.5 dB signal to noise ratio (SNR) using 4QAM, up to 3 times increased throughput in the uplink mode and 10 times reduced channel coding complexity.
Date: May 2015
Creator: Grabner, Mitchell John James
Partner: UNT Libraries

Airbourne WiFi Networks Through Directional Antenna: An Experimental Study

Description: In situations where information infrastructure is destroyed or not available, on-demand information infrastructure is pivotal for the success of rescue missions. In this paper, a drone-carried on demand information infrastructure for long-distance WiFi transmission system is developed. It can be used in the areas including emergency response, public event, and battlefield. The WiFi network can be connected to the Internet to extend WiFi access to areas where WiFi and other Internet infrastructures are not available. In order to establish a local area network to propagate WIFI service, directional antennas and wireless routers are used to create it. Due to unstable working condition on the flying drones, a precise heading turning stage is designed to maintain the two directional antennas facing to each other. Even if external interferences change the heading of the drones, the stages will automatically rotate back to where it should be to offset the bias. Also, to maintain the same flying altitude, a ground controller is designed to measure the height of the drones so that the directional antennas can communicate to each other successfully. To verify the design of the whole system, quite a few field experiments were performed. Experiments results indicates the design is reliable, viable and successful. Especially at disaster areas, it’ll help people a lot.
Date: May 2015
Creator: Gu, Yixin
Partner: UNT Libraries

Integrating environmental data acquisition and low cost Wi-Fi data communication.

Description: This thesis describes environmental data collection and transmission from the field to a server using Wi-Fi. Also discussed are components, radio wave propagation, received power calculations, and throughput tests. Measured receive power resulted close to calculated and simulated values. Throughput tests resulted satisfactory. The thesis provides detailed systematic procedures for Wi-Fi radio link setup and techniques to optimize the quality of a radio link.
Date: December 2009
Creator: Gurung, Sanjaya
Partner: UNT Libraries

The Effect of Mobility on Wireless Sensor Networks

Description: Wireless sensor networks (WSNs) have gained attention in recent years with the proliferation of the micro-electro-mechanical systems, which has led to the development of smart sensors. Smart sensors has brought WSNs under the spotlight and has created numerous different areas of research such as; energy consumption, convergence, network structures, deployment methods, time delay, and communication protocols. Convergence rates associated with information propagations of the networks will be questioned in this thesis. Mobility is an expensive process in terms of the associated energy costs. In a sensor network, mobility has significant overhead in terms of closing old connections and creating new connections as mobile sensor nodes move from one location to another. Despite these drawbacks, mobility helps a sensor network reach an agreement more quickly. Adding few mobile nodes to an otherwise static network will significantly improve the network’s ability to reach consensus. This paper shows the effect of the mobility on convergence rate of the wireless sensor networks, through Eigenvalue analysis, modeling and simulation.
Date: August 2014
Creator: Hasir, Ibrahim
Partner: UNT Libraries

Development and Analysis of a Mobile Node Tracking Antenna Control System

Description: A wireless communication system allows two parties to exchange information over long distances. The antenna is the component of a wireless communication system that allows information to be converted into electromagnetic radiation that propagates through the air. A system using an antenna with a highly directional beam pattern allows for high power transmission and reception of data. For a directional antenna to serve its purpose, it must be accurately pointed at the object it is communicating with. To communicate with a mobile node, knowledge of the mobile node's position must be gained so the directional antenna can be regularly pointed toward the moving target. The Global Positioning System (GPS) provides an accurate source of three-dimensional position information for the mobile node. This thesis develops an antenna control station that uses GPS information to track a mobile node and point a directional antenna toward the mobile node. Analysis of the subsystems used and integrated system test results are provided to assess the viability of the antenna control station.
Date: August 2017
Creator: Hensley, Phillip Hayden
Partner: UNT Libraries