UNT Theses and Dissertations - 144 Matching Results

Search Results

Nano-Manufacturing of Catalytic Amorphous Alloys: In this dissertation, nano-manufacturing of amorphous alloys for electro-catalytic applications is reported and the role of chemistry and active surface area on catalytic behavior is discussed. The catalytic activity of recently developed platinum and palladium-based metallic glasses was studied using cyclic voltammetry and localized electrochemical techniques. The synergistic effect between platinum and palladium was shown for amorphous alloys containing both these elements. The mechanism for superior catalytic behavior was investigated through electronic structure and surface chemical state of the alloys. A correlation between the work function and catalytic performance of the amorphous alloys with widely varying chemistries was established. To address the high cost associated with the noble-metal containing catalysts, the performance of non-noble Ni-P amorphous catalyst was evaluated for electro-catalysis. A facile pulsed electrodeposition approach was used for the nano-manufacturing of these amorphous catalysts. This nano-manufacturing route allowed the synthesis of fully amorphous nano-wires at room temperature for alloys with little or no noble-metal content. A wide range of nano-wires with varying aspect ratios from 25 to 120 was synthesized using commercially obtained anodic aluminum oxide (AAO) nano-molds. Cyclic voltammetry and chrono-amperometry demonstrated superior performance in terms of electrocatalytic activity and stability of the metallic glass nano-wires towards electro-oxidation of methanol. The mechanism for amorphization during pulsed electrodeposition is discussed and compared with the conventional approach of rapid quenching of the liquid melt.
Processing-Structure-Property Relationships of Reactive Spark Plasma Sintered Boron Carbide-Titanium Diboride Composites: Sintering parameter effects on the microstructure of boron carbide and boron carbide/titanium diboride composites are investigated. The resulting microstructure and composition are characterized by scanning electron microscopy (SEM), x-ray microscopy (XRM) and x-ray diffraction (XRD). Starting powder size distribution effects on microstructure are present and effect the mechanical properties. Reactive spark plasma sintering introduces boron nitride (BN) intergranular films (IGF's) and their effects on fracture toughness, hardness and flexural strength are shown. Mechanical testing of Vickers hardness, 3-point bend and Chevron notch was done and the microstructural effects on the resulting mechanical properties are investigated.
Charpy Impact Testing of Twinning Induced Plasticity and Transformation Induced Plasticity High Entropy Alloys: High entropy alloys (HEAs) are a new class of solid solution alloys that contain multiple principal elements and possess excellent mechanical properties, from corrosion resistance to fatigue and wear resistance. Even more recently, twinning induced plasticity (TWIP) and transformation induced plasticity (TRIP) non-equiatomic high entropy alloys have been engineered, promising increased strength and ductility as compared to their equiatomic counterparts. However, impact and fracture resistance of these HEAs has not been studied as much as their other mechanical properties. In this thesis, the hardness, tensile properties, and Charpy impact energy of Al0.3CoCrFeNi, a TWIP HEA, and 50Fe-30Mn-10Co-10Cr (at.%), a TRIP HEA, was explored. First, three processing conditions, (1) as-received, (2) recrystallized, and (3) peak hardness, were chosen for each alloy and verified with Vickers microhardness measurements. Next, the tensile properties of each alloy and condition were investigated. Charpy impact specimen size was then selected based on the final plate thickness, and the machined samples were tested. Plastic zone size and change in sample thickness in the deformed region of each condition after testing was measured. Post-impact test inspection of the samples in all conditions showed that the samples were in tension near the V-notch root and in compression at the impact surface. Plastic zone size is seen to change as a function of distance from the V-notch root moving towards the impact surface in conditions that exhibited higher ductility. Overall, the TWIP alloy displayed high fracture resistance, and further microstructural optimization will likely increase the fracture resistance of these alloys.
Linking Enhanced Fatigue Life to Design by Modifying the Microstructure: Structural material fatigue is a leading cause of failure and has motivated fatigue-resistant design to eliminate risks to human lives. Intrinsic microstructural features alter fatigue deformation mechanisms so profoundly that, essentially, fatigue properties of structural materials become deviant. With this in mind, we initiated this project to investigate the microstructural effect on fatigue behavior of potential structural high entropy alloys. With a better understanding of the effect of microstructure features on fatigue properties, the ultimate goal was to engineer the microstructure to enhance the fatigue life of structural materials. The effects of two major deformation mechanisms presented here are twinning-induced fatigue crack retardation, and transformation-induced fatigue crack retardation. The fundamental principle of both mechanisms is to delay the fatigue crack propagation rate by altering the work hardening ability locally within the crack plastic zone. In ultrafine grained triplex Al0.3CoCrFeNi, nano-sized deformation twins were observed during cyclic loading in FCC matrix due to low stacking fault energy (SFE). The work-hardening ability of the material near the crack was sustained with the formation of twins according to Considere's criteria. Further, due to the ultrafine-grained (UFG) nature of the material, fatigue runout stress was enhanced. In a coarse-grained, dual-phase high entropy alloy, persistent slip bands formed in FCC matrix during cyclic loading due mainly to the slight composition change that affects the SFE in the FCC matrix and eventually alters the deformation mechanism. Another way known to alter an alloy's work hardening (WH) ability is transformation-induced plasticity (TRIP). In some alloys, phase transformation happens due to strain localization, which alters the work-hardening ability. iii In a fine-grained, dual-phase metastable high entropy alloy, gamma (f.c.c.) to epsilon (h.c.p.) transformation occurred in the plastic zone that was induced from cracks. Thus, we designed a Cu-containing FeMnCoCrSi high entropy alloy that exhibited a normalized fatigue ratio …
Extrinsic Doping of Few Layered Tungsten Disulfide Films by Pulsed Laser Deposition: This dissertation tested the hypothesis that pulsed laser deposition (PLD) could be used to create targeted dopant profiles in few layered WS2 films based on congruent evaporation of the target. At the growth temperatures used, 3D Volmer-Weber growth was observed. Increased energy transfer from the PLD plume to the growing films degraded stoichiometry (desorption of sulfur) and mobility. Sulfur vacancies act as donors and produce intrinsic n-type conductivity. Post deposition annealing significantly improved the crystallinity, which was accompanied by a mobility increase from 6.5 to 19.5 cm2/Vs. Preparation conditions that resulted in excess sulfur, possibly in the form of interstitials, resulted in p-type conductivity. Current-voltage studies indicated that Ohmic contacts were governed by surface properties and tunneling. Extrinsic p-type doping of few layered WS2 films with Nb via pulsed laser deposition using ablation targets fabricated from WS2, S and Nb powders is demonstrated. The undoped controls were n-type, and exhibited a Hall mobility of 0.4 cm2/Vs. Films doped at 0.5 and 1.1 atomic percentages niobium were p-type, and characterized by Fermi levels at 0.31 eV and 0.18 eV from the valence band edge. That is, the Fermi level moved closer to the valence band edge with increased doping. With increased Nb doping, the hole concentrations increased from 3.9 x1012 to 8.6 x1013 cm-2, while the mobility decreased from 7.2 to 2.6 cm2/Vs, presumably due to increased ionized impurity scattering. X-ray photoelectron spectroscopy indicates that Nb substitutes on W lattice sites, and the measured peak shifts toward lower binding energy observed corresponded well with the UPS data. Throughout, a clear correlation between degraded stoichiometry and decreased mobility was observed, which indicates that point defect and ionized impurity scattering is a dominant influence on carrier transport in PLD few-layered WS2 films. The approach demonstrates the potential of PLD for targeted doping of …
Phase Transformation and Elastic Constants in Binary Titanium Alloys: An Atomistic Study: The current understanding of the mechanical properties and deformation behavior of some individual phases in titanium alloys is limited due to the fine scale at which these phases precipitate within the β-phase matrix. The α and ω phases represent the most widely observed phases in titanium alloys depending on the alloy composition and also the heat treatment procedure adopted during processing. The possibility of precipitating ω-phase depends on the content of the β-stabilizers within the system. Although a significant compositional partitioning occurs within ω-phase upon aging treatment, the knowledge of ω-phase mechanical properties as a function of composition is very limited. The initial part of the current work focuses on the effect of common β-stabilizers elements on the phase stability and mechanical properties of the ω-phase using first-principles calculations. A relation between the bonding nature, the phase stability, and elastic properties was proposed. Thereafter αʺ martensitic phase was investigated in Ti-Nb and Ti-Nb-O alloys. The phase stability and martensitic start temperature of αʺ-phase was studied as a function of Nb and oxygen content. Also, the effect of the lattice shear distortion induced by oxygen atom on stabilizing β-phase was investigated. Subsequently the effect of the β-stabilizers' elements on stacking faults energy and ductility in α-Ti alloys was studied. Both prismatic and basal slip system were investigated with different concentration of β-stabilizers at the slip plane. Lastly, while the Tadmor and Bernstein model was employed to predict the partial dislocation emission and twinning propensity, the Rice criterion was used to estimate the effect of different β-stabilizers on the ductility of α-Ti alloys.
Understanding the Micromechanism of Cyclic Loading Behavior of Ultrafine Grained Alloys: In the current study, we have investigated the cyclic loading behavior of conventional as well as novel alloy system exhibiting fine and ultrafine-grained structure. While in case of conventional alloy systems (here aluminum alloy AA5024), the effect of three different grain sizes was investigated. Improvement in fatigue properties was observed with decreasing grain size. The unique microstructure produced via Friction stir processing was responsible for the improved fatigue response. Additionally, microstructures consisting of a high fraction of special boundaries within the fine and ultrafine-grained regime were also subjected to cyclic loading. The hierarchical features introduced in the eutectic high entropy alloy deflected the persistent slip bands, responsible for fatigue cracking, thus resulted in delayed crack initiation and improved fatigue life. The selective nature of fatigue was learnt in the fine grain Al0.5CoCrFeNi, where the introduction of hierarchical features did not result in improved fatigue properties. The weak links in the microstructure, while not affecting the tensile properties, got exposed during cyclic loading. Further study on the medium entropy alloy revealed the inherent reason for the improved fatigue properties. The medium entropy alloys utilized the benefit of UFG single-phase FCC matrix. The UFG matrix showed signs of transformation of FCC phase into the HCP phase during fatigue deformation and hence exhibited improved work-hardening. Alongside atomic scale transformation, stacking faults and nano-twins can also be attributed for obtained cyclic properties.
Phase Transformations in Refractory High Entropy Alloys: High entropy alloys (HEAs) based on refractory elements have shown a great potential for high temperature structural applications. In particular, the ones containing Al, exhibits a microstructure similar to the γ-γ' in Ni-based superalloys. While these alloys exhibit impressive strengths at room temperature (RT) and at elevated temperatures, the continuous B2 matrix in these alloys is likely to be responsible for their brittle behavior at RT. Phase stability of five such alloys are studied by thermo-mechanical treatments and characterization techniques using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Two of these alloys showed an inverted microstructure, where the disordered BCC phase becomes continuous, and therefore, they were characterized in detail using SEM, TEM, atom probe tomography (APT) and synchrotron x-ray diffraction experiments. The phenomenon of phase inversion lead to a better combination of strength and ductility as compared to the non-inverted microstructure.To enhance the stability of B2 intermetallic phase which provides the strength when present in a BCC matrix, multicomponent B2 phase compositions stable at 1000°C in some of the above studied alloys, were melted separately. The aim was to establish a single phase B2 at 1000°C and understand the mechanical behavior of these single-phase multicomponent B2 intermetallic alloys. These alloys exhibited a ductile behavior under compression and retained ~1 GPa yield strength at temperature up to 600°C. The ductile nature of these alloys is attributed to the change in bonding nature form directional to metallic bonding, possibly resulting from a significantly high configurational entropy compared to binary or ternary stoichiometric B2 compounds.
Dynamic Deformation and Shear Localization in Friction-Stir Processed Al0.3CoCrFeNi and Fe50Mn30Co10Cr10 High-Entropy Alloys: High entropy alloys (HEAs) are a relatively new class of solid solution alloys that contain multiple principal elements to take advantage of their high configurational entropy, sluggish diffusion, lattice distortion, and the cocktail effect. In recent development, work hardening mechanisms known as twinning induced plasticity (TWIP) and transformation induced plasticity (TRIP) have been found active in Al0.3CoCrFeNi (molar fraction) and Fe50Mn30Co10Cr10 (at %) HEA compositions. Friction-stir processing was done to increase the mechanical properties and improve the microstructure of the alloys for the purpose of high strain rate performance. Quasi-static tensile tests as well as top-hat geometry Split-Hopkinson pressure bar tests were conducted to view the mechanical properties as well as view the microstructural evolution at dynamic strain rates. Overall, the Al0.3CoCrFeNi condition after friction-stir processing and heat treatment has proved to have the best mechanical properties, and selecting from the conditions in this study, Al0.3CoCrFeNi has better shear localization resistance.
Carbon Nanotubes and Molybdenum Disulfide Protected Electrodes for High Performance Lithium-Sulfur Battery Applications: Lithium-sulfur (Li-S) batteries are faced with practical drawbacks of poor cycle life and low charge efficiency which hinder their advancements. Those drawbacks are primarily caused by the intrinsic issues of the cathodes (sulfur) and the anodes (Li metal). In attempt to resolve the issues found on the cathodes, this work discusses the method to prepare a binder-free three-dimensional carbon nanotubes-sulfur (3D CNTs-S) composite cathode by a facile and a scalable approach. Here, the 3D structure of CNTs serves as a conducting network to accommodate high loading amounts of active sulfur material. The efficient electron pathway and the short Li ions (Li+) diffusion length provided by the 3D CNTs offset the insulating properties of sulfur. As a result, high areal and specific capacities of 8.8 mAh cm−2 and 1068 mAh g−1, respectively, with the sulfur loading of 8.33 mg cm−2 are demonstrated; furthermore, the cells operated at a current density of 1.4 mA cm−2 (0.1 C) for up to 150 cycles. To address the issues existing on the anode part of Li-S batteries, this work also covers the novel approach to protect a Li metal anode with a thin layer of two-dimensional molybdenum disulfide (MoS2). With the protective layer of MoS2 preventing the growth of Li dendrites, stable Li electrodeposition is realized at the current density of 10 mA cm−2; also, the MoS2 protected anode demonstrates over 300% longer cycle life than the unprotected counterpart. Moreover, the MoS2 layer prevents polysulfides from corroding the anode while facilitating a reversible utilization of active materials without decomposing the electrolyte. Therefore, the MoS2 protected anode enables a stable cycle life of over 500 cycles at 0.5 C with the high sulfur loading amount of ~7 mg cm−2 (~67 wt% S content in cathode) under the low electrolyte/sulfur (E/S) ratio of 6 μL mg−1. This …
Design of a Polymeric Coating for Protecting Thermoelectric Materials from Sublimation and Oxidation: Thermoelectric (TE) devices can undergo degradation from reactions in corrosive environments and at higher operating temperatures by sublimation and oxidation. To prevent the degradation, we have applied two high temperature polymers (HTPs) as coatings for TE materials. Sintering temperatures were from 250°C to 400°C. We explain why dip coating is better technique in our study and had two potential HTPs for tests. By applying TGA (thermogravimetric analysis), we were able to figure out which HTPs have better thermal resistivity. Besides, TGA also help us to find proper curing cycles for HTPs. EDS and SEM results show that the coatings prevent oxidation and sublimation of TE materials. We also shorten HTP curing cycle time and lower the energy costs.
Substrate Nanotopography and Stiffness Modulation of Cell Behavior: The physical characteristics (i.e., nanostructure and stiffness) of the extracellular matrix where cells reside have been shown to profoundly affect numerous cellular events in vivo and also been employed to modulate cell behavior in vitro, yet how these physical cues regulate cell behavior is still elusive. Therefore, we engineered a variety of nanotopographies with different shapes and dimensions, and investigated how the nanotopographical cue, through focal adhesions-cytoskeleton-nucleus pathway, affected cell phenotype and function. We further designed and fabricated well-defined substrates which had either identical biochemical cue (adhesive ligand presentation) but different nanotopographical cues or identical nanotopography but different biochemical cues, and dissected the roles of these cues in cell modulation. In addition, we revealed that the human mesenchymal stem cells (hMSCs) could obtain nanotopographical memory from the past culture environment, and the nanotopographical memory influenced the future fate decision of the hMSCs. Moreover, we evaluated the effects of substrate nanotopographical and stiffness cues on the fibrogenesis of human lung fibroblasts in response to carbon nanotubes and highlighted the significance of these physical cues in the development of physiologically relevant in vitro models for nanotoxicological study. The mechanistic understanding of the physical regulation of cell behaviors will provide important insight into the advancement of cell culture technologies and the recreation of biomimetic in vitro tissue/organ models.
Bio-Inspired Material Surfaces with Self-cleaning, Micromanipulation and Water Collection: Geckos are famous for the skill of switchable adhesion that they use to stick on various surface while keep their fingers super clean. In the dissertation, a unique mechanism was discovered to explain gecko self-cleaning phenomena. Using atomic force microscopy (AFM), we managed to compare the microparticle-substrate adhesion and the microparticle-seta adhesion with a single seta bonded to the AFM cantilever. A dynamic effect was approved that high pulling-off speed could increase the microparticle-substrate adhesion and thus the self-cleaning appears at high moving speed. Based on the self-cleaning theory, a gecko-inspired N-doped graphene surface with switchable adhesion was achieved, which was designed into a bio-inspired micromanipulator with a success rate over 90%. When electrical bias was applied on this biomimetic surface, the charge concentration induced an electrical double layer (ELD) on the convex surfaces, which attracts polar water molecules to form a water bridge on it, significantly enhancing the adhesion on the wrinkled graphene surface, mimicking the capillary force on beetle feet. Therefore, the bio-inspired adhesive surface can be controlled with speed, electrical bias, humidity and different material surfaces. The water attraction phenomenon on the polarized surface was further tested for the potential application of water collection and evaporation in microsystems.
Process-Structure-Property Relationships in Friction Stir Welded Precipitation Strengthened Aluminum Alloys: Through a series of carefully designed experiments, characterization and some modeling tools, this work is aimed at studying the role of thermal profiles on different microstructural zones and associated properties like strength and corrosion through a variation of weld parameters, thermal boundary conditions and material temper. Two different alloys belonging to the Al-Cu and Al-Cu-Li system in different temper conditions- peak aged (T8) and annealed (O) were used. A 3D-thermal pseudo mechanical (TPM) model is developed for the FSW process using heat transfer module in COMSOL Multiphysics and is based on a heat source wherein the temperature dependent yield shear stress is used for the heat generation. The precipitation and coarsening model is based on the Kampmann and Wagner theoretical framework and accounts for the competition between the various nucleation sites for both metastable and equilibrium precipitates. The model predicts different precipitate mean radius and volume fraction for the various zones in the friction stir welded material. A model for the yield strength is developed which considers contributions from different strengthening mechanisms. The predictions of the each models have been verified against experimental data and literature. At constant advance per rotation, the peak temperature decreases with a decrease in traverse speed and increases with an increase in tool rotation. Weld properties were significantly affected by choice of thermal boundary conditions in terms of backing plate diffusivity. Weld conditions with a higher peak temperature and high strain rate results in more dissolution of precipitates and fragmentation of constituent particles resulting in a better corrosion behavior for the weld nugget. For a peak aged temper of 2XXX alloys, the weld nugget experiences dissolution of strengthening precipitates resulting in a lower strength and the Heat affected zone (HAZ) experiences coarsening of precipitates. For an annealed material, both the weld nugget and HAZ experiences …
Fabrication of Large-Scale and Thickness-Modulated Two-Dimensional Transition Metal Dichalcogenides [2D TMDs] Nanolayers: This thesis describes the fabrication and characterization of two-dimensional transition dichalcogenides (2D TMDs) nanolayers for various applications in electronic and opto-electronic devices applications. In Chapter 1, crystal and optical structure of TMDs materials are introduced. Many TMDs materials reveal three structure polytypes (1T, 2H, and 3R). The important electronic properties are determined by the crystal structure of TMDs; thus, the information of crystal structure is explained. In addition, the detailed information of photon vibration and optical band gap structure from single-layer to bulk TMDs materials are introduced in this chapter. In Chapter 2, detailed information of physical properties and synthesis techniques for molybdenum disulfide (MoS2), tungsten disulfide (WS2), and molybdenum ditelluride (MoTe2) nanolayers are explained. The three representative crystal structures are trigonal prismatic (hexagonal, H), octahedral (tetragonal, T), and distorted structure (Tʹ). At room temperature, the stable structure of MoS2 and WS2 is semiconducting 2H phase, and MoTe2 can reveal both 2H (semiconducting phase) and 1Tʹ (semi-metallic phase) phases determined by the existence of strains. In addition, the pros and cons of the synthesis techniques for nanolayers are discussed. In Chapter 3, the topic of synthesized large-scale MoS2, WS2, and MoTe2 films is considered. For MoS2 and WS2 films, the layer thickness is modulated from single-layer to multi-layers. The few-layer MoTe2 film is synthesized with two different phases (2H or 1Tʹ). The all TMDs films are fabricated using two-step chemical vapor deposition (CVD) method. The analyses of atomic force microscopy (AFM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL), and Raman spectroscopy confirm that the synthesis of high crystalline MoS2, WS2, and MoTe2 films are successful. The electronic properties of both MoS2 and WS2 exhibit a p-type conduction with relatively high field effect mobility and current on/off ratio. In Chapter 4, vertically-stacked few-layer MoS2/WS2 heterostructures on SiO2/Si and flexible polyethylene terephthalate …
The Effect of Processing Conditions on the Surface Morphology of Few-Layered WS2 Thin Films: Recent progress in layered transition metal dichalcogenides (TMDs) has led to various promising electronic and optoelectronic applications. However, the structure of materials plays a critical role in electronic and optoelectronic devices, and determines performance. Electronic and optoelectronic devices typically consist of multiple layers that form electrical homojunctions or heterojunctions. Therefore, in a device it can be expected that a WS2 layer may serve as the substrate for a subsequent layer in a multilayer device stack and determine how the layer grows. In transistor structures, roughness at the channel/gate dielectric interface introduces field variations and charge scattering. Therefore, understanding the relations between processing, surface morphology and properties is important. In this project, the effects of pulsed laser deposition (PLD) processing conditions on the surface morphology of few layered WS2 films were studied. WS2 films were synthesized under processing conditions that represent the extremes of surface supersaturation and kinetic energy transfer from the flux to the growing films, and evolution of the surface morphology was studied. The specific conditions were 1Hz/50mJ, 10Hz/50mJ, 1Hz/300mJ, and 10Hz/300mJ respectively. Combining AFM, XRD and Raman analyses, it was determined that deposition at 10Hz/300mJ, provided the best structural properties and surface morphology. Growth appeared to be 3D-cluster, and was governed by supersaturation rather than by surface diffusion processes. No clear correlation between mobility and surface roughness was found. Hall measurements and XPS data show the highest mobility was obtained with the highest S/W ratio, indicating that point defect scattering rather than scattering from surface roughness was dominant.
Design Principles for Metal-Coordinated Frameworks as Electrocatalysts for Energy Storage and Conversion: In this dissertation, density functional theory calculations are performed to calculate the thermodynamic and electrochemical properties of metal coordinated frameworks for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Gibb's free energy, overpotential, charge transfer and ligands effect are evaluated. The charge transfer analysis shows the positive charges on the metal coordinated frameworks play an essential role in improving the electrochemical properties of the metal coordinated frameworks. Based on the calculations, design principles are introduced to rationally design and predict the electrochemical properties of metal coordinated frameworks as efficient catalysts for ORR and OER. An intrinsic descriptor is discovered for the first time, which can be used as a materials parameter for rational design of the metal coordinated frameworks for energy storage and conversion. The success of the design principles provides a better understanding of the mechanism behind ORR and OER and a screening approach for the best catalyst for energy storage and conversion.
High Temperature Water as an Etch and Clean for SiO2 and Si3N4: An environmentally friendly, and contamination free process for etching and cleaning semiconductors is critical to future of the IC industry. Under the right conditions, water has the ability to meet these requirements. Water becomes more reactive as a function of temperature in part because the number of hydronium and hydroxyl ions increase. As water approaches its boiling point, the concentration of these species increases over seven times their concentrations at room temperature. At 150 °C, when the liquid state is maintained, these concentrations increase 15 times over room temperature. Due to its enhanced reactivity, high temperature water (HTW) has been studied as an etch and clean of thermally grown SiO2, Si3N4, and low-k films. High temperature deuterium oxide (HT-D2O) behaves similarly to HTW; however, it dissociates an order of magnitude less than HTW resulting in an equivalent reduction in reactive species. This allowed for the effects of reactive specie concentration on etch rate to be studied, providing valuable insight into how HTW compares to other high temperature wet etching processes such as hot phosphoric acid (HPA). Characterization was conducted using Fourier transform infrared spectroscopy (FTIR) to determine chemical changes due to etching, spectroscopic ellipsometry to determine film thickness, profilometry to measure thickness change across the samples, scanning electron microscopy (SEM), contact angle to measure changes in wetting behavior, and UV-Vis spectroscopy to measure dissolved silica in post etch water. HTW has demonstrated the ability to effective etch both SiO2 and Si3N4, HT-D2O also showed similar etch rates of Si3N4 indicating that a threshold reactive specie concentration is needed to maximize etch rate at a given temperature and additional reactive species do not further increase the etch rate. Because HTW has no hazardous byproducts, high temperature water could become a more environmentally friendly etchant of SiO2 and Si3N4 thin films.
Mechanisms of Formation and Effects of Transition Metal Oxides in Silicon Nitride on Steel Dry Sliding Contacts: Silicon nitride on steel sliding contacts may provide advantageous tribological properties over traditional self-mated pairs, however the friction and wear behavior at high sliding speeds (>1 m/s) is not well understood. Previous studies at low sliding speeds (< 1 m/s) have found that the wear mechanisms change as a function of the operating parameters, e.g. atmosphere, sliding speed, load, and temperature, due to the formation of transition metal oxides such as Fe2O3 and Fe3O4. This study detected transient effects of the dry silicon nitride on steel contact over a range of sliding speeds to understand their relation to tribochemical reactions and the resulting tribological behavior. Two sets of dry silicon nitride on steel experiments were conducted at 1.45 GPa maximum Hertzian pressure. The first set were low sliding speed reciprocating experiments, conducted at an average of 0.06 m/s, conducted at variable operating temperature, ranging from 23 °C to 1000 °C. In the low sliding speed experiments, transitions of the wear mechanism from adhesive wear, to abrasive wear, then to oxidative wear was observed when the operating temperature increased. The second set were high sliding speed experiments, conducted at variable sliding speeds, ranging from 1 m/s to 16 m/s. In the high sliding speed experiments, a transition from adhesive wear to oxidative wear was observed when the sliding speed surpassed 4.5 m/s. The high sliding speed experiments were accompanied by in-situ instrumentation which detected the presence of a tribofilm which correlated to a reduction in friction, and its formation was linked to tribochemical reactions induced by high flash temperatures. Both sets of experiments had a maximum estimated contact temperature of 1000 °C where oxidative wear was prevalent. Although, the low sliding speed experiments underwent severe bulk oxidation and thermal softening effects, while the high sliding speed experiments experienced localized flash heating …
Molecular Dynamics Simulations of the Structures and Properties of Aluminosilicate and Borosilicate Glasses: Silicate glasses are the most common glass types and have impact on almost every aspect in our lives: from window, containers, to glass fibers for telecommunications. Unlike their crystalline counterparts, glass materials lack long-range order in their atomic arrangement but their structures do possess short and medium range characteristics that play critical roles in their physical and chemical properties. Despite active development of characterization techniques that have contributed to the understanding of glass structures, there remain key challenges in obtaining essential structural features of glasses. Atomistic computer simulations have become an increasingly important method in elucidating the atomic structures and in interpretation and/or prediction of composition-structure-property relationships of complex materials. In this dissertation, classical molecular dynamic (MD) simulations were used to investigate the atomic structures, dynamic and other properties of two important glass systems—aluminosilicate glasses and borosilicate glasses, which are the basis of most industrial and technologically important glasses. Firstly, a comprehensive study of peralkaline Na2O-Al2O3-SiO2 glass with varying Al2O3/SiO2, Na2O/Al2O3, Na2O/SiO2 ratios has been performed to obtain better understanding of the composition–structure–property relationships in this glass system. More than 99% of Al were 4-coordinated in these glasses, validating that Na+ tend to charge balance [AlO4]- network forming units first and then, excess Na+ was used to create non-bridging oxygen (NBO) on Si. As the drop of Na/Al ratio, the percentage of NBO decreases, indicating an increase of the glass network connectivity. In addition, polyhedral connection probability results show that Al tend to be randomly distributed in the glass structure, suggesting a violation of Lowenstein's rule. These structural properties were further used to explain macroscopic properties of glass, such as change of glass transition temperature (Tg) and hardness (Hv) with glass composition. Secondly, molecular dynamics simulations were used to understand the structural, thermal mechanical and diffusion behaviors of spodumene (LiAlSi2O6) …
Friction Stir Welding of Dissimilar Metals: Dissimilar metals joining have been used in many industry fields for various applications due to their technique and beneficial advantages, such as aluminum-steel and magnesium-steel joints for reducing automobile weight, aluminum-copper joint for reducing material cost in electrical components, steel-copper joints for usage in nuclear power plant, etc. The challenges in achieving dissimilar joints are as below. (1) Big difference in physical properties such as melting point and coefficient of thermal expansion led to residual stress and defects. (2) The miscibility issues resulted in either brittle intermetallic compound layer at the welded interface for miscible combinations (such as, aluminum-steel, aluminum-copper, aluminum-titanium, etc.) or no metallurgical bonding for immiscible combinations (such as magnesium-copper, steel-copper, etc.). For metallurgical miscible combinations, brittle intermetallic compounds formed at the welded interface created the crack initiation and propagation path during deformational tests. (3) Stress concentration appeared at the welded interface region during tensile testing due to mismatch in elastic properties of dissimilar materials. In this study, different combinations of dissimilar metals were joined with friction stir welding. Lap welding of 6022-T4 aluminum alloy/galvanized mild steel sheets and 6022-T4 aluminum alloy/DP600 steel sheets were achieved via friction stir scribe technology. The interlocking feature determining the fracture mode and join strength was optimized. Reaction layer (intermetallic compounds layer) between the dissimilar metals were investigated. Butt welding of 5083-H116 aluminum alloy/HSLA-65 steel, 2024-T4 aluminum alloy/316 stainless steel, AZ31/316 stainless steel, WE43/316 stainless steel and 110 copper/316 stainless steel were obtained by friction stir welding. The critical issues in dissimilar metals butt joining were summarized and analyzed in this study including IMC and stress concentration.
Effects of Transition Metal Oxide and Mixed-Network Formers on Structure and Properties of Borosilicate Glasses: First, the effect of transition metal oxide (e.g., V2O5, Co2O3, etc.) on the physical properties (e.g., density, glass transition temperature (Tg), optical properties and mechanical properties) and chemical durability of a simplified borosilicate nuclear waste glass was investigated. Adding V2O5 in borosilicate nuclear waste glasses decreases the Tg, while increasing the fracture toughness and chemical durability, which benefit the future formulation of nuclear waste glasses. Second, structural study of ZrO2/SiO2 substitution in silicate/borosilicate glasses was systematically conducted by molecular dynamics (MD) simulation and the quantitative structure-property relationships (QSPR) analysis to correlate structural features with measured properties. Third, for bioactive glass formulation, mixed-network former effect of B2O3 and SiO2 on the structure, as well as the physical properties and bioactivity were studied by both experiments and MD simulation. B2O3/SiO2 substitution of 45S5 and 55S5 bioactive glasses increases the glass network connectivity, correlating well with the reduction of bioactivity tested in vitro. Lastly, the effect of optical dopants on the optimum analytical performance on atom probe tomography (APT) analysis of borosilicate glasses was explored. It was found that optical doping could be an effective way to improve data quality for APT analysis with a green laser assisted system, while laser spot size is found to be critical for optimum performance. The combined experimental and simulation approach adopted in this dissertation led to a deeper understanding of complex borosilicate glass structures and structural origins of various properties.
Process Improvement of Surface Preparation of Structuraly Bonded Helicopter Detail Parts: The objective of this study was to increase the bond strength at the surface interface of a thin stainless-steel panel for structural bonding on a helicopter. To achieve this objective, six activation methods for applying the coating to the panel in the surface preparation process are presented and explored. Adhesion and roughness tests were conducted to determine which method consistently initiates the etch and improves the bond at the surface. Based on the test results, three methods proved to be effective in initiating the etch. Of the three effective methods, only one method exhibited significantly improved bond strength at the surface interface as well as consistently initiated the etch in solution. The applicability of this method is discussed, and recommendations are presented for further study.
Laser Surface Modification of AZ31B Mg Alloy Bio-Implant Material: Magnesium and its alloys are considered as the potential biomaterials due to their biocompatibility and biodegradable characteristics but suffer from poor corrosion performance. Various surface modification techniques are employed to improve their corrosion resistance. In present case, laser surface melting was carried out on AZ31B Mg alloy with various laser energy densities using a continuous wave ytterbium laser. Effect of laser treatment on phase and microstructure evolution was evaluated by X ray diffraction and scanning electron microscopy. Multi-physics thermal model predicted time temperature evolution along the depth of the laser treatment zone. Additionally, electrochemical method and bio-immersion test were employed to evaluate the corrosion behavior in simulated body fluid medium. Microstructure revealed grain refinement and even distribution of Mg17Al12 phase along the grain boundary for laser treated samples leading to substantial enhancement in the corrosion resistance of the laser treated samples compared to the untreated alloy. The laser processed samples also possessed a superior wettability in SBF solution than the untreated sample. This was further reflected in enhanced bio-integration behavior of laser processed samples. By changing the parameters of laser processing such as power, scanning speed, and fill spacing, a controllable corrosion resistance and bioactivity/biocompatibility of the implant material was achieved.
Room and Elevated Temperature Sliding Wear Behavior of Cold Sprayed Ni-WC Composite Coatings: The tribological properties of cold sprayed Ni-WC metal matrix composite (MMC) coatings were investigated under dry sliding conditions from room temperature (RT) up to 400°C, and during thermal cycling to explore their temperature adaptive friction and wear behavior. Characterization of worn surfaces was conducted using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Raman spectroscopy to determine the chemical and microstructural evolution during friction testing. Data provided insights into tribo-oxide formation mechanisms controlling friction and wear. It was determined that the steady-state coefficient of friction (CoF) decreased from 0.41 at RT to 0.32 at 400˚C, while the wear rate increased from 0.5×10-4 mm3/N·m at RT to 3.7×10-4 mm3/N·m at 400˚C. The friction reduction is attributed primarily to the tribochemical formation of lubricious NiO on both the wear track and transfer film adhered to the counterface. The increase in wear is attributed to a combination of thermal softening of the coating and a change in the wear mechanism from adhesive to more abrasive. In addition, the coating exhibited low friction behavior during thermal cycling by restoring the lubricious NiO phase inside the wear track at high temperature intervals. Therefore, cold sprayed Ni-WC coatings are potential candidates for elevated temperature and thermally self-adaptive sliding wear applications.
Ultrasonic Processing of Aluminum 2139 and 7050: Acoustics is the study of all sound waves, with ultrasound classified as those frequencies above 20,000 Hz. Currently, ultrasound is being used in many industries for a variety of purposes such as ultrasonic imaging, ultrasonic assisted friction stir welding, and ultrasonic spot welding. Despite these uses, the effects of ultrasound on phase stability and resultant mechanical properties has been minimally analyzed. Here we study the impact waves play in ultrasonic welding and design an apparatus to maximize waves entering aluminum alloy samples. Aluminum 2139 and 7050 are used because they are precipitation strengthened by metastable phases so temperature change, and the corresponding phase stability, can greatly impact their strength. Results suggest that the ultrasonic welder primarily imposes a localized temperature spike due to friction, averaging over 200°C in a few seconds, which generally lowers the Vickers hardness due to coarsening or even dissolution of strengthening precipitates. Conversely, the new design increases the Vickers hardness by up to 30% over the initial hardness of approximately 63HV for aluminum 2139 and 83HV for aluminum 7050, respectively, while only increasing the temperature by an average of approximately 10°C. This new design was unable to achieve peak hardness, but the strengthening it achieved in two minutes was equivalent to one month of natural aging. If this system was able to be fine-tuned, it could serve as a quick strengthening process for recently weakened aluminum alloys, such as after friction stir welding.
Processing of NiTi Shape Memory Alloys through Low Pressure and Low Temperature Hydrogen Charging: Many industries including the medical, aerospace, and automobile industries have increasingly adopted the use of shape memory alloys (SMAs) for a plethora of applications due to their unique thermomechanical properties. From the commercially available SMAs in the market, binary NiTi SMAs have shown the most desirable properties. However, SMA properties can be significantly affected by the fabrication process. One of the most familiar applications of NiTi SMAs is in the design of actuating devices where the shape memory effect properties are highly advantageous. Spring NiTi SMA actuators are among the most commonly used and are generally made by torsion loading a straight wire. Consequently, stress concentrations are formed causing a reduction in recovery force. Other methods for producing springs and other NiTi SMA components is the fast emerging manufacturing method of additive manufacturing (AM). AM often uses metal powders to produce the near-net shape components. A major challenge for SMAs, in particular, is their well-known composition sensitivity. Therefore, it is critical to control composition in NiTi SMAs. In this thesis, a novel method for processing NiTi SMAs for pre-alloyed NiTi SMA powders and springs is presented. A low pressure and low temperature hydriding-pulverization-dehydriding method is used for preparing the pre-alloyed NiTi SMA powders with well-controlled compositions, size, and size distributions from wires. By hydrogen charging as-drawn martensitic NiTi SMA wires in a heated H3PO4 solution, pulverizing, and dehydriding, pre-alloyed NiTi powders of various well-controlled sizes are produced. In addition, a low pressure and low temperature hydriding-dehydriding method is used for producing NiTi SMA helixes from wires. The helix pattern in the pre-alloyed NiTi SMA wires was obtained by hydrogen charging NiTi SMA 500 μm diameter wires at different time intervals, followed by dehydriding to remove the hydrogen. The wires, powders, and resulting helixes were characterized using scanning electron microscopy (SEM), …
Alloy Development and High-Energy X-Ray Diffraction Studies of NiTiZr and NiTiHf High Temperature Shape Memory Alloys: NiTi-based shape memory alloys (SMAs) offer a good combination of high-strength, ductility, corrosion resistance, and biocompatibility that has served them well and attracted the attention of many researchers and industries. The alloys unique thermo-mechanical ability to recover their initial shape after relatively large deformations by heating or upon unloading due to a characteristic reversible phase transformation makes them useful as damping devices, solid state actuators, couplings, etc. However, there is a need to increase the temperature of the characteristic phase transformation above 150 °C, especially in the aerospace industry where high temperatures are often seen. Prior researchers have shown that adding ternary elements (Pt, Pd, Au, Hf and Zr) to NiTi can increase transformation temperatures but most of these additions are extremely expensive, creating a need to produce cost-effective high temperature shape memory alloys (HTSMAs). Thus, the main objective of this research is to examine the relatively unstudied NiTiZr system for the ability to produce a cost effective and formable HTSMA. Transformation temperatures, precipitation paths, processability, and high-temperature oxidation are examined, specifically using high energy X-ray Diffraction (XRD) measurements, in NiTi-20 at.% Zr. This is followed by an in situ XRD study of the phase growth kinetics of the favorable H-phase nano precipitates, formed in NiTiHf and NiTiZr HTSMAs, based on prior thermo-mechanical processing in a commercial NiTi-15 at.% Hf HTSMA to examine the final processing methods and aging characteristics. Through this research, knowledge of the precipitation paths in NiTiZr and NiTiHf HTSMAs is extended and methods for characterization of phases and strains using high energy XRD are elucidated for future work in the field.
Surface Chemistry and Work Function of Irradiated and Nanoscale Thin Films Covered Indium Tin Oxides: In this study, we used UV-ozone Ar sputtering, X-ray photoelectron and ultra-violet photoelectron spectroscopies and sputtering based depositions of RuO2 and Se nano-layers on indium tin oxides (ITOs). We elucidated the effect of Ar sputtering on the composition and chemistry of Sn rich ITO surface. We demonstrated that while a combination of UV-ozone radiation and Ar sputtering removes most of the hydrocarbons responsible for degrading the work function of ITO, it also removes significant amount of the segregated SN at the ITO surface that's responsible for its reasonable work function of 4.7eV. We also demonstrated for the first time that sputtering cleaning ITO surface leads to the reduction of the charge state of Sn from Sn4+ to Sn2+ that adds to the degradation of the work function. For the nano-layers coverage of ITO studies, we evaluated both RuO2 and Se. For RuO2 coated ITO, XPS showed the formation of a Ru-Sn-O ternary oxide. The RuO2 nano-layer reduced the oxidation state of Sn in the Sn-rich surface of ITO from +4 to +2. The best work function obtained for this system is 4.98eV, raising the effective work function of ITO by more than 0.5 eV. For the Se coated ITO studies, a systematic study of the dependence of the effective work function on the thickness of Se overage and its chemistry at the Se/ITO interface was undertaken. XPS showed that Se reacts with Sn at the Sn-rich surface of ITO determined the presence of both negative and positive oxidation state of Se at the Se/ITO interface. The Se also reduced the oxidation state of Sn from Sn4+ to Sn2+ in the Sn-rich ITO surface. The highest effective work function obtained for this system is 5.06eV. A combination of RuO2/Se nanoscale coating of optimally cleaned ITO would be a good alternative for …
A Study on NiTiSn Low-Temperature Shape Memory Alloys and the Processing of NiTiHf High-Temperature Shape Memory Alloys: Shape memory alloys (SMAs) operating as solid-state actuators pose economic and environmental benefits to the aerospace industry due to their lightweight, compact design, which provides potential for reducing fuel emissions and overall operating cost in aeronautical equipment. Despite wide applicability, the implementation of SMA technology into aerospace-related actuator applications is hindered by harsh environmental conditions, which necessitate extremely high or low transformation temperatures. The versatility of the NiTi-based SMA system shows potential for meeting these demanding material constraints, since transformation temperatures in NiTi can be significantly raised or lowered with ternary alloying elements and/or Ni:Ti ratio adjustments. In this thesis, the expansive transformation capabilities of the NiTi-based SMA system are demonstrated with a low and high-temperature NiTi-based SMA; each encompassing different stages of the SMA development process. First, exploratory work on the NiTiSn SMA system is presented. The viability of NiTiSn alloys as low-temperature SMAs (LTSMAs) was investigated over the course of five alloy heats. The site preference of Sn in near-equiatomic NiTi was examined along with the effects of solution annealing, Ni:Ti ratio adjustments, and precipitation strengthening on the thermomechanical properties of NiTiSn LTSMAs. Second, the thermomechanical processability of NiTiHf high-temperature SMA (HTSMA) wires is presented. The evolution of various microstructural features (grain size reduction, oxide growth, and nano-precipitation) were observed at incremental stages of the hot rolling process and linked to the thermal and mechanical responses of respective HTSMA rods/wires. This work was carried out in an effort to optimize the rolling/drawing process for NiTiHf HTSMAs.
Processing-Structure-Property Relationships of Spark Plasma Sintered Boron Carbide and Titanium Diboride Ceramic Composites: The aim of this study was to understand the processing – structure – property relationships in spark plasma sintered (SPS) boron carbide (B4C) and B4C-titanium diboride (TiB2) ceramic composites. SPS allowed for consolidation of both B4C and B4C-TiB2 composites without sintering additives, residual phases, e.g., graphite, and excessive grain growth due to long sintering times. A selection of composite compositions in 20% TiB2 feedstock powder increments from 0% to 100%, was sintered at 1900°C for 25 minutes hold time. A homogeneous B4C-TiB2 composite microstructure was determined with excellent distribution of TiB2 phase, while achieving ~99.5% theoretical density. An optimum B4C-23 vol.% TiB2 composite composition with low density of ~3.0 g/cm3 was determined that exhibited ~30-35% increase in hardness, fracture toughness, and flexural bend strength compared to commercial armor-grade B4C. This is a result of a) no residual graphitic carbon in the composites, b) interfacial microcrack toughening due to thermal expansion coefficient differences placing the B4C matrix in compression and TiB2 phase in tension, and c) TiB2 phase aids in crack deflection thereby increasing the amount of intergranular fracture. Collectively, the addition of TiB2 serves as a strengthening and toughening agent, and SPS shows promise for the manufacture of hybrid ceramic composites.
Preventing Thermal Degradation of Pvc Insulation by Mixtures of Cross-Linking Agents and Antioxidants: Poly(vinyl chloride)(PVC) wire and cable insulation has poor thermal stability, causing the plasticizer to separate from the PVC chain and produce an oily residue, lowering the tensile elongation at break and thus increasing brittleness. We have added 4 wt.% of three different types of cross-linking agents and antioxidants, as well as mixtures of both, to improve the thermal stability of the plasticizer and tensile properties of PVC after thermal exposure. We performed tensile tests, tribological tests, profilometry, scanning electron microscopy(SEM) and water absorption determination before and after thermal exposure at 136 ℃ for 1 week. After adding the agents, elongation at break increased by 10 to 20 % while the wear rate and water absorption were lower than for the control sample. Less voids are seen in the SEM images after adding these two kinds of agents. The thermal resistance of the PVC cable insulation is best enhanced by combinations of cross-linking agents and antioxidants.
Investigation into the Semiconducting and Device Properties of MoTe2 and MoS2 Ultra-Thin 2D Materials: The push for electronic devices on smaller and smaller scales has driven research in the direction of transition metal dichalcogenides (TMD) as new ultra-thin semiconducting materials. These ‘two-dimensional' (2D) materials are typically on the order of a few nanometers in thickness with a minimum all the way down to monolayer. These materials have several layer-dependent properties such as a transition to direct band gap at single-layer. In addition, their lack of dangling bonding and remarkable response to electric fields makes them promising candidates for future electronic devices. For the purposes of this work, two 2D TMDs were studied, MoS2 and MoTe2. This dissertation comprises of three sections, which report on exploration of charge lifetimes, investigation environmental stability at elevated temperatures in air, and establishing feasibility of UV laser annealing for large area processing of 2D TMDs, providing a necessary knowledge needed for practical use of these 2D TMDs in optoelectronic and electronic devices. (1) A study investigating the layer-dependence on the lifetime of photo-generated electrons in exfoliated 2D MoTe2 was performed. The photo-generated lifetimes of excited electrons were found to be strongly surface dependent, implying recombination events are dominated by Shockley-Read-Hall effects (SRH). Given this, the measured lifetime was shown to increase with the thickness of exfoliated MoTe¬2; in agreement with SRH recombination. Lifetimes were also measured with an applied potential bias and demonstrated to exhibit a unique voltage dependence. Shockley-Read-Hall recombination effects, driven by surface states were attributed to this result. The applied electric field was also shown to control the surface recombination velocity, which lead to an unexpected rise and fall of measured lifetimes as the potential bias was increased from 0 to 0.5 volts. (2) An investigation into the environmental stability of exfoliated 2D MoTe2 was conducted using a passivation layer of amorphous boron nitride as a …
Recycling of PVC and XLPE for High Impact Resistance in Spool Development: My work focuses on taking waste wire-grade PVC = poly(vinyl chloride) and waste XLPE = cross-linked polyethylene and recycle them into small wire/cable spool technology in order to reduce waste cost and reduce cost of spool production. The PVC and XLPE were provided by Encore Wire Corp. of McKinney, TX; they have also defined the standard to which I am comparing my results. The end goal is to incorporate as much PVC and XLPE into the spools while maintaining material toughness, impact resistance, as well as cost-effectiveness in the implementation of the waste materials. The work has been divided into two primary sections, the first is focused on improving material strength through the addition of ceramic fillers. The second section is focused on adding PVC and XLPE into a stronger and highly cohesive polymer matrix and optimizing the concentration of the waste products. Since XLPE is non-polar while PVC is strongly polar, compatibilizers such as CPE (chlorinated polyethylene) and MA-DCP (maleic anhydride with dicumyl peroxide) were used to improve interactions between polar and non-polar constituents. Testing involved the tensile mechanical properties, tribology and thermal properties, namely dynamic mechanical analysis (DMA) and evaluation of thermal degradation by thermogravimetric analysis (TGA). Combining PVC and XLPE together is not economically feasible with current compatiblizers. At the same time, introduction of PVC waste or XLPE waste with sufficient properties of the resulting composites is doable.
Defining a Relationship between the Flexibility of Materials and Other Properties: Brittleness of a polymeric material has a direct relationship with the material's performance and furthermore shares an inverse relationship with that material's flexibility. The concept of flexibility of materials has been understood but merely explained with a hand-waving manner. Thus, it has never been defined by a calculation, thereby lacking the ability to determine a definite quantitative value for this characteristic. Herein, an equation is presented and proven which makes determining the value of flexibility possible. Such an equation could be used to predict a material's flexibility prior to testing it, thus saving money and valuable time for those in research and in industry. Substantiating evidence showing the relationship between flexibility of polymers and their respective mechanical properties is presented. Further relating the known tensile properties of a given polymer to its flexibility is expanded upon by proving its relationship to the linear coefficient of thermal expansion for each polymer. Additionally, determining flexibility for polymers whose chemical structures have been compromised by respective solvents has also been investigated to predict a solvent's impact on a polymer after exposure. Polymers examined through literature include polycarbonate (PC), polystyrene (PS), teflon (PTFE), styrene acrylonitrile (SAN), acrylonitrile butadiene styrene (ABS), poly(ethersulfone) (PES), low density polyethylene (LDPE), polypropylene (PP), poly(methyl methacrylate) (PMMA), and poly(vinylidene fluoride) (PVDF). Further testing and confirmation was made using PC, PS, ABS, LDPE, PP, and PMMA.
Non-Isothermal Laser Treatment of Fe-Si-B Metallic Glass: Metallic glasses possess attractive properties, such as high strength, good corrosion resistance, and superior soft magnetic performance. They also serve as precursors for synthesizing nanocrystalline materials. In addition, a new class of composites having crystalline phases embedded in amorphous matrix is evolving based on selective crystallization of metallic glasses. Therefore, crystallization of metallic glasses and its effects on properties has been a subject of interest. Previous investigations from our research group related to laser assisted crystallization of Fe-Si-B metallic glass (an excellent soft magnetic material by itself) showed a further improvement in soft magnetic performance. However, a fundamental understanding of crystallization and mechanical performance of laser treated metallic glass was essential from application point of view. In light of this, the current work employed an integrated experimental and computational approach to understand crystallization and its effects on tensile behavior of laser treated Fe-Si-B metallic glass. The time temperature cycles during laser treatments were predicted using a finite element thermal model. Structural changes in laser treated Fe-Si-B metallic glass including crystallization and phase evolution were investigated with the aid of X-ray diffraction, differential scanning calorimetry, resistivity measurements, and transmission electron microscopy. The mechanical behavior was evaluated by uniaxial tensile tests with an InstronTM universal testing machine. Fracture surfaces of the metallic glass were observed using scanning electron microscopy and site specific transmission electron microscopy. Fe-Si-B metallic glass samples treated with lower laser fluence (<0.49 J/mm2) underwent structural relaxation while higher laser flounces led to partial crystallization. The crystallization temperature experienced an upward shift due to rapid heating rates of the order of 104 K/s during laser treatments. The heating cycle was followed by termination of laser upon treatment attainment of peak temperature and rapid cooling of the similar order. Such dynamic effects resulted in premature arrest of the crystallite growth leading …
Modeling of High Strain Rate Compression of Austenitic Shape Memory Alloys: Shape memory alloys (SMAs) exhibit the ability to absorb large dynamic loads and, therefore, are excellent candidates for structural components where impact loading is expected. Compared to the large amount of research on the shape memory effect and/or pseudoelasticity of polycrystalline SMAs under quasi-static loading conditions, studies on dynamic loading are limited. Experimental research shows an apparent difference between the quasi-static and high strain rate deformation of SMAs. Research reveals that the martensitic phase transformation is strain rate sensitive. The mechanism for the martensitic phase transformation in SMAs during high strain rate deformation is still unclear. Many of the existing high strain rate models assume that the latent heat generated during deformation contributes to the change in the stress-strain behavior during dynamic loading, which is insufficient to explain the large stress observed during phase transformation under high strain rate deformation. Meanwhile, the relationship between the phase front velocity and strain rate has been studied. In this dissertation, a new resistance to phase transformation during high strain rate deformation is discussed and the relationship between the driving force for phase transformation and phase front velocity is established. With consideration of the newly defined resistance to phase transformation, a new model for phase transformation of SMAs during high strain rate deformation is presented and validated based on experimental results from an austenitic NiTi SMA. Stress, strain, and martensitic volume fraction distribution during high strain rate deformation are simulated using finite element analysis software ABAQUS/standard. For the first time, this dissertation presents a theoretical study of the microscopic band structure during high strain rate compressive deformation. The microscopic transformation band is generated by the phase front and leads to minor fluctuations in sample deformation. The strain rate effect on phase transformation is studied using the model. Both the starting stress for transformation and …
Effects of HALSs and Nano-ZnO Worked as UV Stabilizers of Polypropylene: This work reports the outdoor weathering performance of ultraviolet (UV)-stabilized polypropylene (PP) products (using PP resins from Encore Wire). Different hindered amine light stabilizers (HALSs) and nano-ZnO were used to stabilize PP-film-based formulations that were exposed under UV light for 6 weeks simulating for in harsh outdoor weather of Dallas, Texas, USA in 2016. Characterization of the exposed PP film products was done in terms of mechanical and friction spectroscopic properties. The PP film formulations were divided into 15 categories based on the type of HALS and nano-ZnO incorporated. This was done to derive meaningful comparison of the various film formulations. Following exposure under UV light, the lifetimes of certain formulations were determined. On the basis of the mechanical and friction properties, it was determined that generally, the HALS or nano-ZnO stabilized PP film give better properties and if those two kinds of UV stabilizers can work together.
Molecular Dynamics Simulations of the Structure and Properties of Boron Containing Oxide Glasses: Empirical Potential Development and Applications: Potential parameters that can handle multi-component oxide glass systems especially boron oxide are very limited in literature. One of the main goals of my dissertation is to develop empirical potentials to simulate multi-component oxide glass systems with boron oxide. Two approaches, both by introducing the composition dependent parameter feature, were taken and both led to successful potentials for boron containing glass systems after extensive testing and fitting. Both potential sets can produce reasonable glass structures of the multi-component oxide glass systems, with structure and properties in good agreement with experimental data. Furthermore, we have tested the simulation settings such as system size and cooling rate effects on the results of structures and properties of MD simulated borosilicate glasses. It was found that increase four-coordinated boron with decreasing cooling rate and system size above 1000 atoms is necessary to produce converged structure. Another application of the potentials is to simulate a six-component nuclear waste glass, international simple glass (ISG), which was for first time simulated using the newly developed parameters. Structural features obtained from simulations agree well with the experimental results. In addition, two series of sodium borosilicate and boroaluminosilicate glasses were simulated with the two sets of potentials to compare and evaluate their applicability and deficiency. Various analyses on the structures and properties such as pair distribution function, total correlation function, coordination number analysis, Qn distribution function, ring size distribution function, vibrational density of states and mechanical properties were performed. This work highlights the challenge of MD simulations of boron containing glasses and the capability of the new potential parameters that enable simulations of wide range of mixed former glasses to investigate new structure features and design of new glass compositions for various applications.
Three-Dimensional Carbon Nanostructure and Molybdenum Disulfide (MoS2) for High Performance Electrochemical Energy Storage Devices: My work presents a novel approach to fabricate binder free three-dimensional carbon nanotubes/sulfur (3DCNTs/S) hybrid composite by a facile and scalable method increasing the loading amount from 1.86 to 8.33 mg/cm2 highest reported to date with excellent electrochemical performance exhibiting maximum specific energy of ~1233Wh/kg and specific power of ~476W/kg, with respect to the mass of the cathode. Such an excellent performance is attributed to the fact that 3DCNTs offers higher loading amount of sulfur, and confine polysulfide within the structure. In second part of the thesis, molybdenum disulfide (MoS2) is typically studied for three electrochemical energy storage devices including supercapacitors, Li-ion batteries, and hybrid Li-ion capacitors. The intrinsic sheet like morphology of MoS2 provides high surface area for double layer charge storage and a layered structure for efficient intercalation of H+/ Li+ ions. My work demonstrates the electrochemical analysis of MoS2 grown on different substrates including copper (conducting), and carbon nanotubes. MoS2 film on copper was investigated as a supercapacitor electrode in three electrode system exhibiting excellent volumetric capacitance of ~330F/cm3 along with high volumetric power and energy density in the range of 40-80 W/cm3 and 1.6-2.4 mWh/cm3, respectively. Furthermore, we have developed novel binder-free 3DCNTs/ MoS2 as an anode materials in half cell Li-ion batteries. The vertically oriented morphology of MoS2 offers high surface area and active electrochemical sites for efficient intercalation of Li+ ions and demonstrating excellent electrochemical performance with high specific capacity and cycling stability. This 3DCNTs/ MoS2 anode was coupled with high surface area southern yellow pine derived activated carbon (SYAC) cathode to obtain hybrid 3DCNTs/ MoS2 || SYAC Li-ion capacitor (LIC), which delivers large operating voltage window of 1-4.0V with excellent cycling stability exhibiting capacitance retention of ~80% after 5000 cycles.
Surface Degradation Behavior of Bulk Metallic Glasses and High Entropy Alloys: In this study, the surface degradation behavior was studied for typical examples from bulk metallic glasses (BMGs), metallic glass composites (MGCs) and high entropy alloys (HEAs) alloy systems that are of scientific and commercial interest. The corrosion and wear behavior of two Zr-based bulk metallic glasses, Zr41.2Cu12.5Ni10Ti13.8Be22.5 and Zr57Cu15.4Ni12.6Al10Nb5, were evaluated in as-cast and thermally relaxed states. Significant improvement in corrosion rate, wear behavior, and friction coefficient was seen for both the alloys after thermal relaxation. Fully amorphous structure was retained with thermal relaxation below the glass transition temperature. This improvement in surface properties was explained by annihilation of free volume, the atomic scale defects in amorphous metals resulting from kinetic freezing. Recently developed MGCs, with in situ crystalline ductile phase, demonstrate a combination of mechanical properties and fracture behavior unseen in known structural metals. The composites showed higher wear rates but lower coefficient of friction compared to monolithic amorphous glasses. No tribolayer formation was seen for the composites in sharp contrast to that of the monolithic metallic glasses. Corrosion was evaluated by open circuit potential (OCP) analysis and potentiodynamic polarization. Site-specific corrosion behavior was studied by scanning vibration electrode technique (SVET) to identify formation of galvanic couples. Scanning kelvin probe microscope was used to map elecropositivity difference between the phases and linked to wear/corrosion behavior. Phases with higher elecropositivity were more susceptible to surface degradation. Wear and corrosion synergy in marine environment was evaluated for two high entropy alloys (HEAs), CoCrFeMnNi and Al0.1CoCrFeNi. Between the two alloys, Al0.1CoCrFeNi showed better wear resistance compared to CoCrFeMnNi in dry and marine conditions due to quicker passivation, a higher magnitude of polarization resistance and significantly larger pitting resistance.
P-type Doping of Pulsed Laser Deposited WS2 with Nb: Layered transition metal dichalcogenides (TMDs) are potentially ideal semiconducting materials due to their in-plane carrier transport and tunable bandgaps, which are favorable properties for electrical and optoelectronic applications. However, the ability to make p-n junctions is the foundation of semiconductor devices, and therefore the ability to achieve reproducible p- and n-type doping in TMD semiconducting materials is critical. In this work, p-type substitutional doping of pulsed laser deposited WS2 films with niobium is reported. The synthesis technique of the PLD target with dopant incorporation which also ensures host material stoichiometry is presented. Hall electrical measurements confirmed stable p-type conductivity of the grown films. Structural characterization revealed that there was no segregation phase of niobium in the fabricated films and x-ray phtoelectron spectroscopy (xps) characterization suggest that the p-type doping is due to Nb4+ which results in p-type behavior. Stable hole concentrations as high as 10E21(cm-3) were achieved. The target fabrication and thin film deposition technique reported here can be used for substitutional doping of other 2D materials to obtain stable doping for device applications.
Additive Manufacturing of Metastable Beta Titanium Alloys: Additive manufacturing processes of many alloys are known to develop texture during the deposition process due to the rapid reheating and the directionality of the dissipation of heat. Titanium alloys and with respect to this study beta titanium alloys are especially susceptible to these effects. This work examines Ti-20wt%V and Ti-12wt%Mo deposited under normal additive manufacturing process parameters to examine the texture of these beta-stabilized alloys. Both microstructures contained columnar prior beta grains 1-2 mm in length beginning at the substrate with no visible equiaxed grains. This microstructure remained constant in the vanadium system throughout the build. The microstructure of the alloy containing molybdenum changed from a columnar to an equiaxed structure as the build height increased. Eighteen additional samples of the Ti-Mo system were created under different processing parameters to identify what role laser power and travel speed have on the microstructure. There appears to be a correlation in alpha lath size and power density. The two binary alloys were again deposited under the same conditions with the addition of 0.5wt% boron to investigate the effects an insoluble interstitial alloying element would have on the microstructure. The size of the prior beta grains in these two alloys were reduced with the addition of boron by approximately 50 (V) and 100 (Mo) times.
Developing Precipitation Hardenable High Entropy Alloys: High entropy alloys (HEAs) is a concept wherein alloys are constructed with five or more elements mixed in equal proportions; these are also known as multi-principle elements (MPEs) or complex concentrated alloys (CCAs). This PhD thesis dissertation presents research conducted to develop precipitation-hardenable high entropy alloys using a much-studied fcc-based equi-atomic quaternary alloy (CoCrFeNi). Minor additions of aluminium make the alloy amenable for precipitating ordered intermetallic phases in an fcc matrix. Aluminum also affects grain growth kinetics and Hall-Petch hardenability. The use of a combinatorial approach for assessing composition-microstructure-property relationships in high entropy alloys, or more broadly in complex concentrated alloys; using laser deposited compositionally graded AlxCrCuFeNi2 (0 < x < 1.5) complex concentrated alloys as a candidate system. The composition gradient has been achieved from CrCuFeNi2 to Al1.5CrCuFeNi2 over a length of ~25 mm, deposited using the laser engineered net shaping process from a blend of elemental powders. With increasing Al content, there was a gradual change from an fcc-based microstructure (including the ordered L12 phase) to a bcc-based microstructure (including the ordered B2 phase), accompanied with a progressive increase in microhardness. Based on this combinatorial assessment, two promising fcc-based precipitation strengthened systems have been identified; Al0.3CuCrFeNi2 and Al0.3CoCrFeNi, and both compositions were subsequently thermo-mechanically processed via conventional techniques. The phase stability and mechanical properties of these alloys have been investigated and will be presented. Additionally, the activation energy for grain growth as a function of Al content in these complex alloys has also been investigated. Change in fcc grain growth kinetic was studied as a function of aluminum; the apparent activation energy for grain growth increases by about three times going from Al0.1CoCrFeNi (3% Al (at%)) to Al0.3CoCrFeNi. (7% Al (at%)). Furthermore, Al addition leads to the precipitation of highly refined ordered L12 (γ′) and B2 precipitates in …
Evolution of Precipitates and Their Influence on the Mechanical Properties of β-Titanium Alloys: Over the last few decades, body-centered-cubic (bcc) beta (β) titanium alloys have largely been exploited as structural alloys owing to the richness in their microstructural features. These features, which lead to a unique combination of high specific strength and ductility, excellent hardenability, good fatigue performance, and corrosion resistance, make these alloys viable candidates for many applications, including aerospace, automobile, and orthopedic implants. The mechanical properties of these alloys strongly depend on the various phases present; which can be controlled by thermomechanical treatments and/or alloy design. The two most important and studied phases are the metastable ω phase and the stable α phase. The present study focuses on the microstructural evolution and the mechanical behavior of these two phases in a model β-Ti alloy, binary Ti-12wt. %Mo alloy, and a commercial β-Ti alloy, β-21S. Microstructures containing athermal and isothermal ω phases in the binary Ti-12wt. %Mo alloy are obtained under specific accurate temperature controlled heat treatments. The formation and the evolution of the ω-phase based microstructures are investigated in detail via various characterization techniques such as SEM, TEM, and 3D atom probe tomography. The mechanical behavior was investigated via quasi-static tensile loading; at room and elevated temperatures. The effect of β phase stability on the deformation behavior is then discussed. Similar to the Ti-12wt. %Mo, the formation and the evolution of the athermal and isothermal ω phases in the commercial β-21S alloy was studied under controlled heat treatments. The structural and compositional changes were tracked using SEM, TEM, HR-STEM, and 3D atom probe tomography (3D-APT). The presence of additional elements in the commercial alloy were noted to make a considerable difference in the evolution and morphology of the ω phase and also the mechanical behavior of the alloys. The Portevin-Le Chatelier (PLC) like effect was observed in iii this alloy at …
Laser Additive Manufacturing of Magnetic Materials: A matrix of variably processed Fe-30at%Ni was deposited with variations in laser travel speeds as well and laser powers. A complete shift in phase stability occurred as a function of varying laser travel speed. At slow travel speeds, the microstructure was dominated by a columnar fcc phase. Intermediate travel speeds yielded a mixed microstructure comprised of both the columnar fcc and a martensite-like bcc phase. At the fastest travel speed, the microstructure was dominated by the bcc phase. This shift in phase stability subsequently affected the magnetic properties, specifically saturation magnetization. Ni-Fe-Mo and Ni-Fe-V permalloys were deposited from an elemental blend of powders as well. Both systems exhibited featureless microstructures dominated by an fcc phase. Magnetic measurements yielded saturation magnetizations on par with conventionally processed permalloys, however coercivities were significantly larger; this difference is attributed to microstructural defects that occur during the additive manufacturing process.
Design Principle on Carbon Nanomaterials Electrocatalysts for Energy Storage and Conversion: We are facing an energy crisis because of the limitation of the fossil fuel and the pollution caused by burning it. Clean energy technologies, such as fuel cells and metal-air batteries, are studied extensively because of this high efficiency and less pollution. Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are essential in the process of energy storage and conversion, and noble metals (e.g. Pt) are needed to catalyze the critical chemical reactions in these devices. Functionalized carbon nanomaterials such as heteroatom-doped and molecule-adsorbed graphene can be used as metal-free catalysts to replace the expensive and scarce platinum-based catalysts for the energy storage and conversion. Traditionally, experimental studies on the catalytic performance of carbon nanomaterials have been conducted extensively, however, there is a lack of computational studies to guide the experiments for rapid search for the best catalysts. In addition, theoretical mechanism and the rational design principle towards ORR and OER also need to be fully understood. In this dissertation, density functional theory calculations are performed to calculate the thermodynamic and electrochemical properties of heteroatom-doped graphene and molecule-adsorbed graphene for ORR and OER. Gibb's free energy, overpotential, charge transfer and edge effect are evaluated. The charge transfer analysis show the positive charges on the graphene surface caused by the heteroatom, hetero-edges and the adsorbed organic molecules play an essential role in improving the electrochemical properties of the carbon nanomaterials. Based on the calculations, design principles are introduced to rationally design and predict the electrochemical properties of doped graphene and molecule-adsorbed graphene as metal-free catalysts for ORR and OER. An intrinsic descriptor is discovered for the first time, which can be used as a materials parameter for rational design of the metal-free catalysts with carbon nanomaterials for energy storage and conversion. The success of the design principle provides a better …
Exceptional Properties in Friction Stir Processed Beta Titanium Alloys and an Ultra High Strength Steel: The penchant towards development of high performance materials for light weighting engineering systems through various thermomechanical processing routes has been soaring vigorously. Friction stir processing (FSP) - a relatively new thermomechanical processing route had shown an excellent promise towards microstructural modification in many Al and Mg alloy systems. Nevertheless, the expansion of this process to high temperature materials like titanium alloys and steels is restricted by the limited availability of tool materials. Despite it challenges, the current thesis sets a tone for the usage of FSP to tailor the mechanical properties in titanium alloys and steels. FSP was carried out on three near beta titanium alloys, namely Ti6246, Ti185 and Tiβc with increasing β stability index, using various tool rotation rates and at a constant tool traverse speed. Microstructure and mechanical property relationship was studied using experimental techniques such as SEM, TEM, mini tensile testing and synchrotron x-ray diffraction. Two step aging on Ti6246 had resulted in an UTS of 2.2GPa and a specific strength around 500 MPa m3/mg, which is about 40% greater than any commercially available metallic material. Similarly, FSP on an ultra-high strength steel―Eglin steel had resulted in a strength greater than 2GPa with a ductility close to 10% at around 4mm from the top surface of stir zone (SZ). Experimental techniques such as microhardness, mini-tensile testing and SEM were used to correlate the microstructure and properties observed inside SZ and HAZ's of the processed region. A 3D temperature modeling was used to predict the peak temperature and cooling rates during FSP. The exceptional strength ductility combinations inside the SZ is believed to be because of mixed microstructure comprised of various volume fractions of phases such as martensite, bainite and retained austenite.
Structure Evolution and Nano-Mechanical Behavior of Bulk Metallic Glasses and Multi-Principal Element Alloys: Bulk metallic glasses and multi-principal element alloys represent relatively new classes of multi-component engineering materials designed for satisfying multiple functionalities simultaneously. Correlating the microstructure with mechanical behavior (at the microstructural length-scales) in these materials is key to understanding their performance. In this study, the structure evolution and nano-mechanical behavior of these two classes of materials was investigated with the objective of fundamental scientific understanding of their properties. The structure evolution, high temperature nano-mechanical behavior, and creep of two Zr-based alloys was studied: Zr41.2Ti13.8Cu12.5Ni10.0Be22 (Vitreloy1) and Zr52.5Ti5Cu17.9Ni14.6All0 (Vitreloy105). Devitrification was found to proceed via the formation of a metastable icosahedral phase with five-fold symmetry. The deformation mechanism changes from inhomogeneous or serrated flow to homogenous flow near 0.9Tg, where Tg is the glass transition temperature. The creep activation energy for Vitreloy1 and Vitreloy105 were 144 kJ/mol and 125 kJ/mol, respectively in the range of room temperature to 0.75Tg. The apparent activation energy increased drastically to 192 kJ/mol for Vitreloy1 and 215 kJ/mol for Vitreloy105 in the range of 0.9Tg to Tg, indicating a change in creep mechanism. Structure evolution in catalytic amorphous alloys, Pt57.5Cu14.7Ni5.3P22.5 and Pd43Cu27Ni10P20, was studied using 3D atom probe tomography and elemental segregation between different phases and the interface characteristics were identified. The structure evolution of three multi-principal element alloys were investigated namely CoCrNi, CoCrFeMnNi, and Al0.1CoCrFeNi. All three alloys formed a single-phase FCC structure in as-cast, cold worked and recrystallized state. No secondary phases precipitated after prolonged heat treatment or mechanical working. The multi-principal element alloys showed less strain gradient plasticity compared to pure metals like Ni during nano-indentation. This was attributed to the highly distorted lattice which resulted in lesser density of geometrically necessary dislocations (GNDs). Dislocation nucleation was studied by low load indentation along with the evaluation of activation volume and activation energy. This was …
Microstructural Evolution and Mechanical Response of Materials by Design and Modeling: Mechanical properties of structural materials are highly correlated to their microstructure. The relationship between microstructure and mechanical properties can be established experimentally. The growing need for structural materials in industry promotes the study of microstructural evolution of materials by design using computational approaches. This thesis presents the microstructural evolution of two different structural materials. The first uses a genetic algorithm approach to study the microstructural evolution of a high-temperature nickel-based oxide-dispersion-strengthened (ODS) alloy. The chosen Ni-20Cr ODS system has nano Y2O3 particles for dispersion strengthening and submicron Al2O3 for composite strengthening. Synergistic effects through the interaction of small dispersoids and large reinforcements improved high-temperature strength. Optimization considered different weight factors on low temperature strength, ductility, and high temperature strength. Simulation revealed optimal size and volume fraction of dispersoids and reinforced particles. Ni-20Cr-based alloys were developed via mechanical alloying for computational optimization and validation. The Ni-20Cr-1.2Y2O3-5Al2O3 alloy exhibited significant reduction in the minimum creep rate (on the order of 10-9 s-1) at 800oC and 100 MPa. The second considers the microstructural evolution of AA 7050 alloy during friction stir welding (FSW). Modeling the FSW process includes thermal, material flow, microstructural and strength modeling. Three-dimensional material flow and heat transfer model was developed for friction stir welding process of AA 7050 alloy to predict thermal histories and extent of deformation. Peak temperature decreases with the decrease in traverse speed at constant advance per revolution, while the increase in tool rotation rate enhances peak temperature. Shear strain is higher than the longitudinal and transverse strain for lower traverse speed and tool rotation rate; whereas for higher traverse speed and tool rotation rate, shear and normal strain acquire similar values. Precipitation distribution simulation using TC-PRISMA predicts the presence of η' and η in the as-received AA 7050-T7451 alloy and mostly η in the friction …

UNT Theses and Dissertations - 144 Matching Results

Search Results

Add Filters

Applied Filters