UNT Theses and Dissertations - 71 Matching Results

Search Results

Analyze and Rebuild an Apparatus to Gauge Evaporative Cooling Effectiveness of Micro-Porous Barriers.

Description: The sample used for evaporative cooling system is Fabric defender 750 with Shelltite finish. From the experimental data and equations we have diffusion coefficient of 20.9 ± 3.71 x 10-6 m2/s for fabric with one layer with 17%-20% fluctuations from the theory, 27.8 ± 4.5 x 10-6 m2/s for fabric with two layers with 6%-14% fluctuations from the theory and 24.9 ± 4.1 x 10-6 m2/s for fabric with three layers with 13%-16% fluctuations from the theory. Since the thickness of the fabric increases so the mass transport rate decreases so the mass transport resistance should be increases. The intrinsic mass resistances of Fabri-1L, Fabri-2L and Fabri-3L are respectively 104 ± 10.2 s/m, 154 ± 23 s/m and 206 ± 26 s/m from the experiment.
Date: December 2008
Creator: Mohiti Asli, Ali
Partner: UNT Libraries

Errors in skin temperature measurements.

Description: Numerical simulation is used to investigate the accuracy of a direct-contact device for measuring skin-surface temperature. A variation of thermal conductivity of the foam has greater effect on the error rather than a variation of the blood perfusion rate. For a thermal conductivity of zero, an error of 1.5 oC in temperature was identified. For foam pad conductivities of 0.03 and 0.06 W/m-oC, the errors are 0.5 and 0.15 oC. For the transient study, with k=0 W/m-oC, it takes 4,900 seconds for the temperature to reach steady state compared with k=0.03 W/m-oC and k=0.06 W/m-oC where it takes 3,000 seconds. The configuration without the foam and in presence of an air gap between the skin surface and the sensor gives the most uniform temperature profile.
Date: December 2008
Creator: Dugay, Murielle
Partner: UNT Libraries

Quasi-Three Dimensional Experiments on Liquid-Solid Fluidized Bed of Three Different Particles in Two Different Distributors

Description: This thesis is an experimental study of the fluidization of binary mixture in particulate flows. A fluidized bed with two distributors was built with water being used as carrying fluid. Three types of solid particles of nylon, glass and aluminum of the same size and different densities are used in the experiments. The wall effect on a single particle fluidization, the fluidization of binary mixture of large density difference (nylon and aluminum of density ratio of 0.42), and the fluidization of binary mixture of close density (glass and aluminum with density ratio of 0.91) were investigated. Also, the effect of distributors on mono-disperse and bi-disperse particle fluidization was investigated. Results show that the presence of narrow walls reduces the minimum fluidization velocity for a single particle by as much as nearly 40%. Also, in the case of binary mixture of close density particles, uniform mixing was easily achieved and no segregation was observed, but in the case of large density difference particles, there exists significant segregation and separation. At high velocity, the uniform distributor behaves like a transport bed. To achieve a full bed in the single jet, it requires 1.5 times velocity of the uniform distributor. This behavior determines their application in the industries.
Date: December 2009
Creator: Obuseh, Chukwuyem Charles
Partner: UNT Libraries

Ultrafast Laser Sampling of a Plant Tissue and ion Conductivity Measurement for Investigation of Light Stress Generation Mechanisms

Description: In this study we applied ultra-short laser pulses on a biological sample (Arabidopsis), in order to cut it precisely in a square pattern and subsequently use it for studying stress generation mechanisms. For this purpose, we utilized femtosecond laser pulses at 100 fs pulse width and 80 MHz repetition rate. We took two processing parameters into consideration such as laser power, laser exposure time which is related to the stage speed. Therefore, we were able to find the laser optimum conditions for ablation of biological tissues. The mutant and wildtype (control) obtained from laser cutting with a size of 500 µm × 500 µm were directly transferred (in-situ with laser cutting) into a microfabricated chamber containing ~500 nanoliters deionized water for measuring ion conductivity. The ion conductivity is a signature of cell-death mechanisms caused by various stresses. A light with intensity of 100 µmol was exposed to the samples for 2 hours and 20 minutes as a source of stress. A quantitative electrical analysis with high accuracy was assured by utilizing a microchamber, which enables a measurement in nanoliter volume. We measured the impedance which is reciprocal of conductivity using a lock-in amplifier and a precise current source at frequency of 130 Hz. Initially high impedance of mutant sample tended to drop within 2 hours and finally approached the constant value which signified that the cell death mechanism was complete. However, the wildtype sample demonstrated approximately constant impedance (conductivity) during the experiment.
Date: August 2010
Creator: Abtahi, Seyed Ali
Partner: UNT Libraries

Experimental Study on Fluidization of Biomass, Inert Particles, and Biomass/Sand Mixtures

Description: Fluidization of biomass particles is an important process in the gasification, pyrolysis and combustion in order to extract energy from biomass. Studies on the fluidization of biomass particles (corn cob and walnut shell), inert particles (sand, glass bead, and alumina), which are added to facilitate fluidization of biomass, and biomass/sand mixture were performed. Experiments were carried out in a 14.5 cm internal diameter cold flow fluidization bed to determine minimum fluidization velocities with air as fluidizing medium. On the of basis of experimental data from both present work and those found in the literature, new correlations were developed to predict minimum fluidization velocity for inert particles as well as biomass particles. It was found that the proposed correlations satisfactorily predict minimum fluidization velocities and was in well agreement with experimental data. Furthermore, effect of weight percentage of biomass in the biomass/sand mixtures was studied. The weight fraction of biomass particles in the mixture was chosen in the range of 0 ~ 100 wt. %. The results show that minimum fluidization velocity of the mixtures increases with an increase in biomass content. Using the present experimental data, a new correlation was developed in terms of mass ratio for predicting values of minimum fluidization velocity of these mixtures. However, the validity of the proposed correlation should be further studied by conducting more experiments using the biomass/sand mixtures of different particle size, shape, and density.
Date: May 2011
Creator: Paudel, Basu
Partner: UNT Libraries

High-Precision Micropipette Thermal Sensor for Measurement of Thermal Conductivity of Carbon Nanotubes Thin Film

Description: The thesis describes novel glass micropipette thermal sensor fabricated in cost-effective manner and thermal conductivity measurement of carbon nanotubes (CNT) thin film using the developed sensor. Various micrometer-sized sensors, which range from 2 µm to 30 µm, were produced and tested. The capability of the sensor in measuring thermal fluctuation at micro level with an estimated resolution of ±0.002oC is demonstrated. The sensitivity of sensors was recorded from 3.34 to 8.86 µV/oC, which is independent of tip size and dependent on the coating of Nickel. The detailed experimental setup for thermal conductivity measurement of CNT film is discussed and 73.418 W/moC was determined as the thermal conductivity of the CNT film at room temperature.
Date: August 2011
Creator: Shrestha, Ramesh
Partner: UNT Libraries

Energy Usage While Maintaining Thermal Comfort : A Case Study of a UNT Dormitory

Description: Campus dormitories for the University of North Texas house over 5500 students per year; each one of them requires certain comfortable living conditions while they live there. There is an inherit amount of money required in order to achieve minimal comfort levels; the cost is mostly natural gas for water and room heating and electricity for cooling, lighting and peripherals. The US Department of Energy has developed several programs to aid in performing energy simulations to help those interested design more cost effective building designs. Energy-10 is such a program that allows users to conduct whole house evaluations by reviewing and altering a few parameters such as building materials, solar heating, energy efficient windows etc. The idea of this project was to recreate a campus dormitory and try to emulate existent energy consumption then try to find ways of lowering that usage while maintaining a high level of personal comfort.
Date: December 2011
Creator: Gambrell, Dusten
Partner: UNT Libraries

Analysis of Sources Affecting Ambient Particulate Matter in Brownsville, Texas

Description: Texas is the second largest state in U.S.A. based on geographical area, population and the economy. It is home to several large coastal urban areas with major industries and infrastructure supporting the fossil-fuel based energy sector. Most of the major cities on the state have been impacted by significant air pollution events over the past decade. Studies conducted in the southern coastal region of TX have identified long range transport as a major contributor of particulate matter (PM) pollution along with local emissions. Biomass burns, secondary sulfates and diesel emissions sources are comprise as the dominant mass of PM2.5 have been noted to be formed by the long range transport biomass from Central America. Thus, the primary objective of this study was to identify and quantify local as well as regional sources contributing to the PM pollution in the coastal area of Brownsville located along the Gulf of Mexico. Source apportionment techniques such as principal component analysis (PCA) and positive matrix factorization (PMF) were employed on the air quality monitoring data to identify and quantify local and regional sources affecting this coastal region. As a supplement to the PMF and PCA, conditional probability function (CPF) analysis and potential source contribution function (PSCF) analysis were employed to characterize the meteorological influences for PM events. PCA identified an optimal solution of 6 sources affecting the coastal area of Brownsville, while PMF resolved 8 sources for the same area. Biomass comingled with sea salt was identified to be the dominant contributor from the PCA analysis with 30.2% of the apportioned PM mass in Brownsville, meanwhile PMF account secondary sulfates I & II with 27.6%. the other common sources identified included, biomass burning, crustal dust, secondary sulfate, oil combustion, mobile sources and miscellaneous traffic sources.
Date: May 2012
Creator: Diaz Poueriet, Pablo
Partner: UNT Libraries

Laminar Natural Convection From Isothermal Vertical Cylinders

Description: Laminar natural convection heat transfer from the vertical surface of a cylinder is a classical subject, which has been studied extensively. Furthermore, this subject has generated some recent interest in the literature. In the present investigation, numerical experiments were performed to determine average Nusselt numbers for isothermal vertical cylinders (103 < RaL < 109, 0.5 < L/D <10, and Pr = 0.7) with and without an adiabatic top in a quiescent ambient environment which will allow for plume growth. Results were compared with commonly used correlations and new average Nusselt number correlations are presented. Furthermore, the limit for which the heat transfer results for a vertical flat plate may be used as an approximation for the heat transfer from a vertical cylinder was investigated.
Date: August 2012
Creator: Day, Jerod
Partner: UNT Libraries

Quantification of Anthropogenic and Natural Sources of Fine Particles in Houston, Texas Using Positive Matrix Factorization

Description: Texas, due to its geographical area, population, and economy is home to a variety of industrialized areas that have significant air quality problems. These urban areas are affected by elevated levels of fine particulate matter (PM2.5). The primary objective of this study was to identify and quantify local and regional sources of air pollution affecting the city of Houston, Texas. Positive Matrix Factorization (PMF) techniques were applied to observational datasets from two urban air quality monitoring sites in Houston from 2003 through 2008 in order to apportion sources of pollutants affecting the study region. Data from 68 species for Aldine and 91 for Deer Park were collected, evaluated, and revised to create concentration and uncertainty input files for the PMF2 and EPA PMF (PMF3) source apportionment models. A 11-sources solution for Aldine and 10-sources for Deer Park were identified as the optimal solutions with both models. The dominant contributors of fine particulate matter in these sites were found to be biomass burnings (2%-8.9%), secondary sulfates I (21.3%-7.6%) and II (38.8%-22.2%), crustal dust (8.9%-10.9%), industrial activities (10.9%-4.2%), traffic (23.1%-15.6%), secondary nitrates (4.4%-5.5%), fresh (1%-1.6%) and aged(5.1%-4.6%) sea salt and refineries (1.3%-0.6%), representing a strong case to confirm the high influence of local activities from the industrial area and the ship channel around the Houston channel. Additionally, potential source contribution function (PSCF) and conditional probability function (CPF) analyses were performed to identify local and regional source-rich areas affecting this urban airshed during the study period. Similarly, seasonal variations and patterns of the apportioned sources were also studied in detail.
Date: August 2012
Creator: Peña Sanchez, Carlos Alberto
Partner: UNT Libraries

Simulation Study of Tremor Suppression and Experiment of Energy Harvesting with Piezoelectric Materials

Description: The objective of this research is to develop a wearable device that could harvest waste mechanical energy of the human hand movement and utilize this energy to suppress wrist tremors. Piezoelectric material is used to measure the hand movement signals, and the signal of wrist tremor is filtered to be utilized to suppress the tremor. In order to conduct the experiment of energy harvesting and tremor suppression, an experimental rig was fabricated. Two types of piezoelectric materials, PVDF (polyvinylidene fluoride) films and MFC (macro fiber composite) films, are used to harvest mechanical energy and used as actuators to suppress hand tremors. However, due to some shortages of the materials, these two types of materials are not used as actuators to suppress the wrist tremors. Thus, we use Matlab Simulink to simulate the tremor suppression with AVC (active vibration control) algorithm.
Date: August 2012
Creator: Ou, Jianqiang
Partner: UNT Libraries

Estimation of Aircraft Emissions for the Corpus Christi International Airport, Corpus Christi, Texas

Description: Commercial aviation is a vital part of the United States economy. It generates over $1 trillion annually, which is more than 5% of the U.S. GDP, and produces approximately 10 million jobs. Every year there is an increase in commercial air traffic. This is attributed to expanding trade between states and other countries, which requires larger amounts of cargo aircraft in operation, and also catering to the growing number of middle and upper class passengers who travel for business and pleasure purposes. A rise in commercial aviation leads to the use of more aviation fuel on a monthly and annual basis. This in turn leads to escalated levels of combustion by-products from jet and turbofan engines into the atmosphere. The negative effects of these by-products range from producing poor air quality and consequent health hazards to contributing to global warming. This study is aimed at assessing the impacts of aircraft emissions on the local air quality in Corpus Christi using the Emissions and Dispersion Modeling System. Flight data for the study was obtained from the Department of Transportation's Research and Innovative Technology Administration. Analyses of the emissions were compared on monthly, annual, engine type and airline provider bases. Climatic, economic and anthropogenic factors were identified in the analyses.
Date: May 2013
Creator: Thomas, Gregson Johann
Partner: UNT Libraries

Thermal Characterization of Austenite Stainless Steel (304) and Cnt Films of Varying Thickness Using Micropipette Thermal Sensors

Description: Thermal transport behavior of austenite stainless steel stripe (304) and the carbon nano-tubes (CNTs) films of varying thickness are studied using a micropipette thermal sensor. Micropipette sensors of various tip sizes were fabricated and tested for the sensitivity and reliability. The sensitivity deviated by 0.11 for a batch of pipette coated under same physical vapor deposition (PVD) setting without being affected by a tip size. Annealing, rubber coating and the vertical landing test of the pipette sensor proved to be promising in increasing the reliability and durability of the pipette sensors. A micro stripe (80µm × 6µm × 0.6µm) of stainless steel, fabricated using focused ion beam (FIB) machining, was characterized whose thermal conductivity was determined to be 14.9 W/m-K at room temperature. Similarly, the thermal characterization of CNT films showed the decreasing tendency in the thermal transport behavior with the increase in the film thickness.
Date: May 2013
Creator: Dangol, Ashesh
Partner: UNT Libraries

Using a Multimodal Sensing Approach to Characterize Human Responses to Affective and Deceptive States

Description: Different ways to measure human affective and deceptive reactions to stimulus have been developed. One method is a multimodal approach using web camera, thermal imaging camera and physiological sensors data to extract different features in the human face (verbal and non-verbal behavior) such as breathing rate, heart rate, face temperature, skin conductance, eye tracking, language analysis and facial expressions among others. Human subjects from different ages and ethnicity were exposed to two different experiments were they watched videos (affection recognition) and others answered an interview session (deception recognition). With the data collected from videos (thermal and visual), different regions of interest (ROI) of the face were selected as well as the whole picture. The ROI were determined based on the most sensitive parts of the face where larger changes of temperature or other physiological features are recorded. It was also analyzed the language (written and spoken) in order to obtain the verbal modalities. The data has been compared among the subjects to determine whether the deceptive and affective reactions of a person can be predicted using multimodal approach. From the multiple data obtained, a characterization of reactions is proposed when subjects are exposed to different stimulus, positive or negative, as well as deceptive behavior and later on recognize if the person is happy, sad, nervous, anxious, telling the truth, lying etc. Using the multimodal approach we were able to predict automatically, with higher accuracy than the baseline, affective and deceptive states of a person. In the affective state recognition, the classifier software differentiated affective state versus neutral state with 92.85% accuracy. Then it differentiated Positive State, Negative State and Neutral State with 57.14% accuracy. Additionally, it differentiated Positive State versus Negative State with 73.21% accuracy. Finally, the classifier was able to predict Deceptive State (people lying) and Non Deceptive State ...
Date: May 2013
Creator: Narvaez-Valle, Alexis
Partner: UNT Libraries

Effect of Dispersed Particles and Branching on the Performance of a Medium Temperature Thermal Energy Storage System

Description: The main objective of my thesis is to develop a numerical model for small-scale thermal energy storage system and to see the effect of dispersing nano-particles and using fractal-like branching heat exchanger in phase change material for our proposed thermal energy storage system. The associated research problems investigated for phase change material (PCM) are the low thermal conductivity and low rate of heat transfer from heat transfer fluid to PCM in thermal energy storage system. In this study an intensive study is carried out to find the best material for thermal storage and later on as a high conductive nano-particle graphite is used to enhance the effective thermal conductivity of the mixed materials. As a thermal storage material molten solar Salt (60% NaNO3+40%KNO3) has been selected, after that detailed numerical modeling of the proposed design has been done using MATLAB algorithm and following the fixed grid enthalpy method. The model is based on the numerical computation of 1-D finite difference method using explicit scheme. The second part of the study is based on enhancing the heat transfer performance by introducing the concept of fractal network or branching heat exchanger. Results from the numerical computation have been utilized for the comparison between a conventional heating system (with a simple single tube as a heat exchanger) and a passive PCM thermal energy storage system with branching heat exchanger using NTU-effectiveness method and charging time calculation. The comparison results show a significant amount improvement using branching network and mixing nano-particle in terms of heat transfer (13.5% increase in effectiveness of branching level-02 heat exchangers from the conventional one ), thermal conductivity (increased 73.6% with 20% graphite nano-particle mix with solid PCM), charging time (57% decrease of charging time for the effect of both the dispersion of Graphite nano-particle and branching heat exchange) and ...
Date: August 2013
Creator: Hasib, A. M. M. Golam
Partner: UNT Libraries

Investigation of an Investment Casting Method Combined with Additive Manufacturing Methods for Manufacturing Lattice Structures

Description: Cellular metals exhibit combinations of mechanical, thermal and acoustic properties that provide opportunities for various implementations and applications; light weight aerospace and automobile structures, impact and noise absorption, heat dissipation, and heat exchange. Engineered cell topologies enable one to control mechanical, thermal, and acoustic properties of the gross cell structures. A possible way to manufacture complex 3D metallic cellular solids for mass production with a relatively low cost, the investment casting (IC) method may be used by combining the rapid prototyping (RP) of wax or injection molding. In spite of its potential to produce mass products of various 3D cellular metals, the method is known to have significant casting porosity as a consequence of the complex cellular topology which makes continuous fluid's access to the solidification interface difficult. The effects of temperature on the viscosity of the fluids were studied. A comparative cost analysis between AM-IC and additive manufacturing methods is carried out. In order to manufacture 3D cellular metals with various topologies for multi-functional applications, the casting porosity should be resolved. In this study, the relations between casting porosity and processing conditions of molten metals while interconnecting with complex cellular geometries are investigated. Temperature, and pressure conditions on the rapid prototyping – investment casting (RP-IC) method are reported, thermal stresses induced are also studied. The manufactured samples are compared with those made by additive manufacturing methods.
Date: August 2013
Creator: Kodira, Ganapathy D.
Partner: UNT Libraries

A Performance Analysis of Solar Chimney Passive Ventilation System in the Unt Zero Energy Lab

Description: The purpose of this investigation is to find out suitability of the solar chimney natural ventilation system in a Zero Energy Lab located at the University of North Texas campus, to figure out performance of the solar chimney. Reduction in the heating and ventilation and air conditioning energy consumption of the house has been also analyzed. The parameters which are considered for investigation are volumetric flow rate of outlet of chimney, the absorber wall temperature and glass wall temperatures. ANSYS FLUENT 14.0 has been employed for the 3-D modeling of the solar chimney. The dimensions of the solar chimney are 14’2” X 7’4” X 6’11”. The flow inside solar chimney is found to be laminar and the simulation results show that maximum outlet volumetric flow rate of about 0.12m3/s or 432 cfm is possible from chimney. The experimental velocity of chimney was found to be 0.21 m/s. Density Boussinesq approximation is considered for the modeling. Velocity and temperature sensors have been installed at inlet and outlet of the chimney in order to validate the modeling results. It is found that based on simulated volumetric flow rate that cooling load of 9.29 kwh can be saved and fan power of 7.85 Watts can be saved.
Date: August 2013
Creator: Talele, Suraj H.
Partner: UNT Libraries

Performance Analysis of Two Alternative Hvac Systems for the Unt Zero Energy Lab

Description: This paper covers the simulation and comparison among three different HVAC (heating, ventilation & air conditioning)systems to achieve the goal of finding the most effective HVAC among these three in terms of human comfort, efficiency and cost considering North Texas climate. In the Zero Energy Lab at the University of North Texas, Denton, TX, the HVAC system of the building assembles with geothermal heat source. Here, water to water heat pump with radiant floor and water to air heat pump with air ducts provide heating & cooling of the building. In this paper electricity consumption, comfort, cost & efficiency analysis is done for the existing system using Energy Plus simulation software. Calibration of the simulated data of the existing system is done comparing with the actual data. Actual data is measured using 150 sensors that installed in Zero Energy Lab. After the baseline model calibration, simulation for ground source water to water heat pump, evaporative cooler with baseboard electric heater and water cooled electric chiller with baseboard electric heater (as a conventional system) is shown. Simulation results evaluate the life cycle cost (LCC) for these HVAC systems. The results of the comparison analysis among all the three HVAC systems show the most effective HVAC system among these three systems in North Texas weather. The results will make UNT Zero Energy lab a standard model towards a sustainable green future.
Date: August 2013
Creator: Hasib, Naimee
Partner: UNT Libraries

Sensitivity and Uncertainty Analysis of Occupancy-related Parameters in Energy Modeling of Unt Zero Energy Lab

Description: The study focuses on the sensitivity and uncertainty analysis of occupancy-related parameters using Energyplus modeling method. The model is based on a real building Zero Energy Lab in Discovery Park, at University of North Texas. Four categories of parameters are analyzed: heating/cooling setpoint, lighting, equipment and occupancy. Influence coefficient (IC) is applied in the sensitivity study, in order to compare the impact of individual parameter on the overall building energy consumption. The study is conducted under Texas weather file as well as North Dakota weather file in order to find weather’s influence of sensitivity. Probabilistic collocation method (PCM) is utilized for uncertainty analysis, with an aim of predicting future energy consumption based on history or reference data set. From the study, it is found that cooling setpoint has the largest influence on overall energy consumption in both Texas and North Dakota, and occupancy number has the least influence. The analysis also indicates schedule’s influence on energy consumption. PCM is able to accurately predict future energy consumption with limited calculation, and has great advantage over Monte Carlo Method. The polynomial equations are generated in both 3-order and 6-order, and the 6-order equation is proved to have a better result, which is around 0.1% compared with real value.
Date: August 2013
Creator: Xiong, Guangyuan
Partner: UNT Libraries

Characterization of Viscoelastic Properties of a Material Used for an Additive Manufacturing Method

Description: Recent development of additive manufacturing technologies has led to lack of information on the base materials being used. A need arises to know the mechanical behaviors of these base materials so that it can be linked with macroscopic mechanical behaviors of 3D network structures manufactured from the 3D printer. The main objectives of my research are to characterize properties of a material for an additive manufacturing method (commonly referred to as 3D printing). Also, to model viscoelastic properties of Procast material that is obtained from 3D printer. For this purpose, a 3D CAD model is made using ProE and 3D printed using Projet HD3500. Series of uniaxial tensile tests, creep tests, and dynamic mechanical analysis are carried out to obtained viscoelastic behavior of Procast. Test data is fitted using various linear and nonlinear viscoelastic models. Validation of model is also carried out using tensile test data and frequency sweep data. Various other mechanical characterization have also been carried out in order to find density, melting temperature, glass transition temperature, and strain rate dependent elastic modulus of Procast material. It can be concluded that melting temperature of Procast material is around 337°C, the elastic modulus is around 0.7-0.8 GPa, and yield stress is around 16-19 MPa.
Date: December 2013
Creator: Iqbal, Shaheer
Partner: UNT Libraries

Multi-year Operation Effect of Geothermal Heat Exchanger on Soil Temperature for Unt Zero Energy Lab

Description: Ground source heat pump (GSHP) uses earth’s heat to heat or cool space. Absorbing heat from earth or rejecting heat to the earth, changes soil’s constant temperature over the multiple years. In this report we have studied about Soil temperature change over multiple years due to Ground loop heat exchanger (GLHE) for Zero Energy Research Laboratory (ZØE) which is located in Discovery Park, University of North Texas, Denton, TX. We did 2D thermal analysis GLHP at particular Depth. For simulation we have used ANSYS workbench for pre-processing and FLUENT ANYS as solver. TAC Vista is software that monitors and controls various systems in ZØE. It also monitors temperature of water inlet/outlet of GLHE. For Monitoring Ground temperatures at various depths we have thermocouples installed till 8ft from earth surface, these temperatures are measured using LabVIEW. From TAC Vista and LabVIEW Reading’s we have studied five parameters in this report using FLUENT ANSYS, they are; (1) Effect of Time on soil Temperature change over Multi-years, (2) Effect of Load on soil temperature change over Multi-years, (3) Effect of Depth on soil temperature change over Multi-years, (4) Effect of Doubling ΔT of inlet and outlet of GLHE on soil temperature change over multi-years and (5) Effect on soil temperature change for same ZØE Laboratory, if it’s in Miami, Florida. For studying effect of time on soil temperature change for multi-years, we have varied heating and cooling seasons. We have four cases they are Case A: GSHP always “ON” (1) 7 months cooling and 5 month cooling and (2) 257 days are cooling and 108 days heating. Case B: GSHP “OFF” for 2 months (1) 7 months cooling and 3 months heating and (2) 6 months cooling and 4 month heating. For Studying Effect of Load on soil temperature change over multi-years, we ...
Date: December 2013
Creator: Walikar, Vinayak P.
Partner: UNT Libraries

Using a Multimodal Sensing Approach to Characterize Human Thermal Comfort Level

Description: A method to distinguish human level of comfort has been developed by using a thermal camera, physiological sensors, and a surroundings sensor. The method has successfully collected data from hominal facial features, breathing rate, skin temperature, room temperature, blood volume pressure, relative humidity, and air velocity. Participants from all genders and races were involved in two sessions of a human comfort experiment including a psychology survey session. The variables, such as room temperature and clothing are controlled to maintain steady test conditions. The region of interest was determined by body temperature and facial temperature as registered by the thermal imaging camera. To experience different levels of discomfort, participants were required to perform two different activities. The first session included an activity on the air resistance elliptical and the second session required the subjects to remain steady in front of a fan. The data was subsequently compared on all subjects to determine whether human discomfort and comfort can be predicted by using various approaches. The parameters of discomfort and comfort were simulated to characterize human levels of comfort. According to arrangement of correlation among thermal comfort responses, blood volume pressure, skin temperature, respiration, and skin conduction, we are be able to predict discomfort and comfort affective states.
Date: December 2013
Creator: Wicaksono, Cakra Aditya
Partner: UNT Libraries

High-Density Polyethylene/Peanut Shell Biocomposites

Description: A recent trend in the development of renewable and biodegradable materials has led to the development of composites from renewal sources such as natural fibers. This agricultural activity generates a large amount of waste in the form of peanut shells. The motivation for this research is based on the utilization of peanut shells as a viable source for the manufacture of biocomposites. High-density polyethylene (HDPE) is a plastic largely used in the industry due to its durability, high strength to density ratio, and thermal stability. This research focuses in the mechanical and thermal properties of HDPE/peanut shell composites of different qualities and compositions. The samples obtained were subjected to dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical tensile strength tests. TO prepare the samples for analysis, the peanut shells were separated into different mesh sizes and then mixed with HDPE at different concentrations. The results showed that samples with fiber size number 10 exhibited superior strength modulus of 1.65 GPa versus results for HDPE alone at 1.32 GPa. The analysis from the previous experiments helped to determine that the fiber size number 10 at 5%wt. ratio in HDPE provides the most optimal mechanical and thermal results. From tensile tests the highest modulus of elasticity of 1.33 GPa was achieved from the samples of peanut shells size number 10 in HDPE at 20%wt. ratio, while the results for HDPE alone were only of 0.8 GPa. The results proved the hypothesis that the addition of peanut shells to HDPE enhances both the thermal and mechanical properties of the composite.
Access: This item is restricted to UNT Community Members. Login required if off-campus.
Date: May 2014
Creator: Londoño Ceballos, Mauricio
Partner: UNT Libraries

Optimization of Superhydrophobic Surfaces to Maintain Continuous Dropwise Condensation

Description: In the past decade, the condensation on superhydrophobic surfaces has been investigated abundantly to achieve dropwise condensation. There is not a specific approach in choosing the size of the roughness of the superhydrophobic surfaces and it was mostly selected arbitrarily to investigate the behavior of condensates on these surfaces. In this research, we are optimizing the size of the roughness of the superhydrophobic surface in order to achieve dropwise condensation. By minimizing the resistances toward the transition of the tails of droplets from the cavities of the roughness to the top of the roughness, the size of the roughness is optimized. It is shown that by decreasing the size of the roughness of the superhydrophobic surface, the resistances toward the transition of the tails of droplets from Wenzel state to Cassie state decrease and consequently dropwise condensation becomes more likely.
Access: This item is restricted to UNT Community Members. Login required if off-campus.
Date: May 2014
Creator: Vandadi, Aref
Partner: UNT Libraries