UNT Theses and Dissertations - 8 Matching Results

Search Results

Results: 1 - 8
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of Immersion Cooled ARM-Based Computer Clusters for Low-Cost, High-Performance Computing

Description: This study aimed to investigate performance of ARM-based computer clusters using two-phase immersion cooling approach, and demonstrate its potential benefits over the air-based natural and forced convection approaches. ARM-based clusters were created using Raspberry Pi model 2 and 3, a commodity-level, single-board computer. Immersion cooling mode utilized two types of dielectric liquids, HFE-7000 and HFE-7100. Experiments involved running benchmarking tests Sysbench high performance linpack (H… more
Date: August 2017
Creator: Mohammed, Awaizulla Shareef
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of Spray Cooling Schemes for Dynamic Thermal Management

Description: This study aims to investigate variable flow and intermittent flow spray cooling characteristics for efficiency improvement in active two-phase thermal management systems. Variable flow spray cooling scheme requires control of pump input voltage (or speed), while intermittent flow spray cooling scheme requires control of solenoid valve duty cycle and frequency. Several testing scenarios representing dynamic heat load conditions are implemented to characterize the overall performance of variable… more
Date: May 2017
Creator: Yata, Vishnu Vardhan Reddy
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Seismic Performance Evaluation of Novel Cold-Formed Steel Framed Shear Walls Sheathed with Corrugated Steel Sheets

Description: This thesis presents experiments and numerical analysis of a novel cold-formed steel framed shear wall sheathed with corrugated steel sheets. The objective of this newly designed shear wall is to meet the growing demand of mid-rise buildings and the combustibility requirement in the International Building Code. The strength of the novel shear wall is higher than currently code certified shear wall in AISI S400-15 so that it could be more favorable for mid-rise building in areas that are prone t… more
Date: August 2017
Creator: Lan, Xing
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Shear and Bending Strength of Cold-Formed Steel Solid Wall Panels Using Corrugated Steel Sheets for Mobile Shelters

Description: The objective of this thesis is to determine if the single sided resistance spot weld (RSW) can be used as a feasible connection method for cold formed steel (CFS) shear walls subject to lateral force of either seismic or wind loads on mobile shelters. The research consisted of three phases which include: a design as a 3D BIM model, connection tests of the resistance spot weld, and full-scale testing of the designed solid wall panels. The shear wall testing was conducted on specimens with both … more
Date: December 2017
Creator: Derrick, Nathan Lynn
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Shear and Compression Strength of Cold-formed Steel Clip Angles Subjected to Different Screw Patterns

Description: This thesis presents experiments and numerical analysis of the cold-formed steel clip angle in three different limit states which are shear, compression, and combination of the screw connection. A previous cold-formed steel clip angle test program (which is Phase 1) developed design methods for clip angle. Therefore, the object of this thesis is to further investigate the behavior and design methods of loading-bearing cold-formed steel clip angles under different screw pattern. For each limit … more
Date: December 2017
Creator: Yan, Zhishan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Study on the System Reliability of Cold-Formed Steel Roof Trusses

Description: This thesis presents a research project aimed at advancing the treatment of cold-formed steel (CFS) structural reliability in roof trusses. Structural design today relies almost exclusively on component-level design, so structural safety is assured by limiting the probability of failure of individual components. Reliability of the entire system is typically not assessed, so in a worst-case scenario the system reliability may be less than the component reliability, or in a best-case scenario the… more
Date: May 2017
Creator: Johnson, Adam M.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Two-Phase Spray Cooling with HFC-134a and HFO-1234yf for Thermal Management of Automotive Power Electronics using Practical Enhanced Surfaces

Description: The objective of this research was to investigate the performance of two-phase spray cooling with HFC-134a and HFO-1234yf refrigerants using practical enhanced heat transfer surfaces. Results of the study were expected to provide a quantitative spray cooling performance comparison with working fluids representing the current and next-generation mobile air conditioning refrigerants, and demonstrate the feasibility of this approach as an alternative active cooling technology for the thermal manag… more
Date: August 2017
Creator: Altalidi, Sulaiman Saleh
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen