Technical Report Archive and Image Library (TRAIL) - 4,626 Matching Results

Search Results

The 1350 F stress-rupture properties of two wrought alloys and three cast alloys

Description: From Summary: "These properties compare favorably with those of the strongest similar alloys previously investigated. However, compared with a 60Cr-25Fe-15Mo alloy, the three cobalt-chronium-nickel cast alloys are inferior. A correlation of NACA and OSRD (Project NRC-8) data is presented, showing the variation of rupture strengths with temperature in the range of 1350^o to 2000^o for alloys."
Date: November 1947
Creator: Reynolds, E E; Freeman, J W & White, A E
Partner: UNT Libraries Government Documents Department

Abrasive Blasting for Cleaning Parts

Description: Abstract: A demonstration on August 22, 1945, showed that Alpha or Beta M or K parts, including insulators, can be well cleaned with a pressure-feed abrasive blaster. The abrasive is a slurry of alumina and water mixed with high velocity air in a special feed nozzle. The slurry is continuously recycled.
Date: September 1945
Creator: McWherter, Jack R. & Yerazunis, Stephen
Partner: UNT Libraries Government Documents Department

Abstracts pertaining to seaplanes

Description: Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.
Date: July 24, 1947
Creator: Bidwell, Jerold M & King, Douglas A
Partner: UNT Libraries Government Documents Department

Acceleration Characteristics of R-3350 Engine Equipped with NACA Injection Impeller

Description: Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump. The vacuum-operated accelerating pump of the hydraulic-metering carburetor was modified to produce satisfactory accelerations by supplementing the standard air chamber with an additional 75-cubic spring. The throttle-actuated accelerating pump of the direct-metering carburetor was modified to produce satisfactory accelerations by replacing the standard 0.028-inch-diameter bleed in the load-compensator balance line with a smaller bleed of 0.0225-inch diameter. The results of this investigation indicated that both carburetors can be easily modified to produce satisfactory acceleration characteristics of the engine and no definite choice between the types of carburetor and accelerating pump can be made. Use of the direct-metering carburetor, however, probably resulted in better fuel distribution to the cylinders during the acceleration period and reduced the backfire hazard because all the fuel is introduced through the injection impeller.
Date: January 8, 1947
Creator: Hickel, Robert O. & Snider, William E.
Partner: UNT Libraries Government Documents Department

Acceleration Measurements During Landing in Rough Water of a 1/7-Scale Dynamic Model of Grumman XJR2F-1 Amphibian - Langley Tank Model 212, TED No. NACA 2378

Description: Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size). Maximum normal accelerations of about 6.5g were obtained in 4.4 inch waves and 8.5g were obtained in 8.0 inch waves. A maximum angular acceleration corresponding to 16 radians per second per second, full size, was obtained in the higher waves. The data indicate that the airplane will experience its greatest accelerations when landing in waves of about 20 feet (140 ft, full size) in length.
Date: May 6, 1947
Creator: Land, Norman S. & Zeck, Howard
Partner: UNT Libraries Government Documents Department

Acceleration Measurements During Landings of a 1/5.5-Size Dynamic Model of the Columbia XJL-1 Amphibian in Smooth Water and in Waves: Langley Tank Model 208M, TED No. NACA 2336

Description: A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g. During landings in rough water the greatest vertical acceleration measured was 15.4g, for a landing in 6.4-foot by 165-foot waves. The impact accelerations increased with increase in wave height and, in general, decreased with increase in wave length. During the landings in waves the model bounced into the air at stalled attitudes at speeds below flying speed. The model trimmed up to the mechanical trim stop (20 deg) during landings in waves of heights greater than 2.0 feet. Solid water came over the bow and damaged the propeller during one landing in 6.4-foot waves. The vertical acceleration coefficients at first impact from the tank tests of a 1/5.5-size model were in fair agreement with data obtained at the Langley impact basin during tests of a 1/2-size model of the hull.
Date: September 25, 1947
Creator: Clement, Eugene P. & Havens, Robert F.
Partner: UNT Libraries Government Documents Department

Accelerations and bottom pressures measured on a B-24D airplane in a ditching test

Description: From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."
Date: November 1944
Creator: Steiner, Margaret F.
Partner: UNT Libraries Government Documents Department

The Accumulation of Radioactivity as Shown by a Limnological Study of the Columbia River in the Vicinity of Hanford Works : Preliminary Report

Description: The following report provides data collected during an investigation in the Columbia River. The purpose of this investigation was to research the radioactivity present in the bottom-living organisms of the river.
Date: November 12, 1948
Creator: Coopey, R. W.
Partner: UNT Libraries Government Documents Department

Accuracy of airspeed measurements and flight calibration procedures

Description: From Summary: "The sources of error that may enter into the measurement of airspeed by pitot-static methods are reviewed in detail together with methods of flight calibration of airspeed installations. Special attention is given to the problem of accurate measurements of airspeed under conditions of high speed and maneuverability required of military airplanes." (author).
Date: 1948
Creator: Huston, Wilber B
Partner: UNT Libraries Government Documents Department