National Advisory Committee for Aeronautics (NACA) - Browse

ABOUT BROWSE FEED

Additional design charts relating to the stalling of tapered wings

Description: From Introduction: "The present report, therefore, may be considered a supplement to reference 1. The combined scope of the stall charts of reference 1, designated A, and of the present work, designated B, is summarized in the following table: For the wing with root thickness ratio to 18 was also investigated.
Date: January 1943
Creator: Harmon, Sidney M
Partner: UNT Libraries Government Documents Department

Additional fatigue tests on effects of design details in 355-T6 sand-cast aluminum alloy

Description: From Introduction: "Reported herein are results of the additional direct-stress fatigue tests on: (1) a plate-type specimen with cored centrally located hole and (2) 0.300-inch-diameter round polished specimens with various degrees of porosity."
Date: March 10, 1954
Creator: Eaton, I D & Youra, John A
Partner: UNT Libraries Government Documents Department

Additional free-flight tests of the rolling effectiveness of several wing-spoiler arrangements at high subsonic, transonic, and supersonic speeds

Description: From Introduction: "The purpose of the present paper is to present results obtained recently relating to the characteristics of a full-span sharp-edge spoiler with an 0.02-chord projection above the wing surface at several chordwise positions and also to the relative effectiveness of the sharp-edge spoiler and a wedge-type spoiler located at the 80-percent-chord line."
Date: November 24, 1948
Creator: Strass, H Kurt
Partner: UNT Libraries Government Documents Department

The additional-mass effect of plates as determined by experiments

Description: From Introduction: "The apparent increase in the inertia properties of a body moving in a fluid medium has been called the additional-mass effect. This report presents a resume of test procedures and results of experimental determinations of the additional-mass effect of flat plates. In addition to data obtained from various foreign sources and from a NACA investigation in 1933, the results of tests recently conducted by the National Advisory Committee for Aeronautics are included."
Date: 1941
Creator: Gracey, William
Partner: UNT Libraries Government Documents Department

Additional measurements of the low-speed static stability of a configuration employing three triangular wing panels and a body of equal length

Description: From Introduction: "The results of an investigation of the low-speed static stability of a simplified model of such an arrangement having one of the airfoils placed vertically on top of the body and the other two as wing panels having negative dihedral are presented in reference 1. In order to provide information for predicting the effects of changes in the basic configuration on the low-speed stability characteristics presented in reference 1, additional measurements have been made."
Date: July 25, 1955
Creator: Delany, Noel K
Partner: UNT Libraries Government Documents Department

Additional results of an investigation at transonic speeds to determine the effects of a heated propulsive jet on the drag characteristics of a series of related afterbodies

Description: From Introduction: "Presented in this report are the basic data obtained from investigation. The data are presented with limited analysis in order to expedite their availability to those concerned with jet-exit-afterbody design."
Date: September 24, 1956
Creator: Henry, Beverly Z JR & Cahn, Maurice S
Partner: UNT Libraries Government Documents Department

Additional Results on the Static Longitudinal and Lateral Stability Characteristics of a 0.05-Scale Model of the Convair F2Y-1 Airplane at High Subsonic Speeds

Description: Additional results on the static longitudinal and lateral stability characteristics of a 0.05-scale model of the Convair F2Y-1 water-based fighter airplane were obtained in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.92. The maximum angle-of-attack range (obtained at the lower Mach numbers) was from -2 degrees to 25 degrees. The sideslip-angle range investigated was from -4 degrees to 12 degrees. The investigation included effects of various arrangements of wing fences, leading-edge chord-extensions, and leading-edge notches. Various fuselage fences, spoilers, and a dive brake also were investigated. From overall considerations of lift, drag, and pitching moments, it appears that there were two modifications somewhat superior to any of the others investigated: One was a configuration that employed a full-chord fence and a partial-chord fence located at 0.63 semispan and 0.55 semispan, respectively. The second was a leading-edge chord-extension that extended from 0.68 semispan to 0.85 semispan in combination with a leading-edge notch located at 0.68 semispan. With plus or minus 10 degrees aileron, the estimated wing-tip helix angle was reduced from 0.125 at a Mach number of 0.50 to 0.088 at a Mach number of 0.92, with corresponding rates of roll of 4.0 and 5.2 radians per second. The upper aft fuselage dive brake, when deflected 30 degrees and 60 degrees, reduced the rudder effectiveness about 10 to 20 percent and about 35 to 50 percent, respectively.
Date: August 10, 1954
Creator: Spreeman, Kenneth P. & Few, Albert G.
Partner: UNT Libraries Government Documents Department

Additional static and fatigue tests of high-strength aluminum-alloy bolted joints

Description: From Introduction: "Early in 1951 the National Advisory Committee for Aeronautics published, as Technical Note 2276 (ref. 1), a report by the Aluminum Research Laboratories of the Aluminum Company of America on the results of static and fatigue tests of high-strength aluminum alloy monobloc specimens and bolted joints. In view of special interest shown by several aircraft companies, certain expansions of the test program were undertaken by the Aluminum Research Laboratories and are reported herein."
Date: July 1954
Creator: Hartmann, E C; Holt, Marshall & Eaton, I D
Partner: UNT Libraries Government Documents Department

Additional test data on static longitudinal stability

Description: From Summary: "The purpose of this investigation was to explore the influence of weights of the controls on the stability with elevator released. The available test data were extended to stability with elevator locked. In this connection the study of the propeller effect seemed of vital importance."
Date: August 1934
Creator: Hubner, Walter
Partner: UNT Libraries Government Documents Department

Adhesion of ice in its relation to the de-icing of airplanes

Description: From Summary: "The various possible means of preventing ice adhesion on airplane surfaces are critically reviewed. Results are presented of tests of the adhesives forces between ice and various solid and liquid forces. It is concluded that the de-icing of airplane wings by heat from engine exhaust shows sufficient promise to warrant full-scale tests. For propellers, at least, and possibly for certain small areas such as windshields, radio masts, etc. the use of de-icing or adhesion-preventing liquids will provide the best means of protection."
Date: August 1939
Creator: Rothrick, A M & Selden, R
Partner: UNT Libraries Government Documents Department

Adhesive and protective characteristics of ceramic coating A-417 and its effect on engine life of forged Refractaloy-26 (AMS 5760) and cast stellite 21 (AMS 5385) turbine blades

Description: The adhesive and protective characteristics of National Bureau of Standards Coating A-417 were investigated, as well as the effect of the coating on the life of forged Refractaloy 26 and cast Stellite 21 turbine blades. Coated and uncoated blades were run in a full-scale J33-9 engine and were subjected to simulated service operations consisting of consecutive 20-minute cycles (15 min at rated speed and approximately 5 min at idle). The ceramic coating adhered well to Refractaloy 26 and Stellite 21 turbine blades operated at 1500 degrees F. The coating also prevented corrosion of the Refractaloy 26, a corrosion-sensitive nickel-base alloy, and of the Stellite 21, a relatively corrosion-resistant cobalt-base alloy. Although the coating prevented corrosion of both alloys, it had no apparent effect on blade life.
Date: February 12, 1953
Creator: Garrett, Floyd B & Gyorgak, Charles A
Partner: UNT Libraries Government Documents Department

Advantages of oxide films as bases for aluminum pigmented surface coatings for aluminum alloys

Description: Report discussing both laboratory and weather-exposure corrosion tests showed conclusively that the protection afforded by aluminum pigmented spar varnish coatings applied to previously anodized aluminum surfaces was greatly superior to that afforded by the same coatings applied to surfaces which had simply been cleaned free from grease and not anodized.
Date: November 1931
Creator: Buzzard, R W & Mutchler, W H
Partner: UNT Libraries Government Documents Department

Aerial navigation by dead reckoning

Description: Report discussing the problem to be solved, as presented to the pilot or observer of an aircraft, is as follows: The aircraft starting from A must land at B, the only data being the speed of the airplane, the altitude and the orientation D of the course. The above data would be amply sufficient, were it not for the fact that the airplane is constantly subjected to a wind of variable direction and strength.
Date: July 1922
Creator: Maffert, Pierre
Partner: UNT Libraries Government Documents Department

Aerial navigation : on the problem of guiding aircraft in a fog or by night when there is no visibility

Description: Report discussing the use of magnetic fields and wire to navigate aircraft in conditions of poor visibility is presented. This field may be considered to be derived from a double lemniscate, considered in the particular case where the origin is a double point formed from the magnetic field of the slack wire, from the field produced by the return currents and from the field due to the currents induced in the conducting mass. These fields are dephased in two ways, one in the direction of the wire, the other in a direction perpendicular to it.
Date: January 1922
Creator: Loth, William
Partner: UNT Libraries Government Documents Department