National Advisory Committee for Aeronautics (NACA) - Browse

ABOUT BROWSE FEED

Aerodynamic Characteristics at High and Low Subsonic Mach Numbers of the NACA 0012, 64(sub 2)-015, and 64(sub 3)-018 Airfoil Sections at Angles of Attack from -2 Degrees to 30 Degrees

Description: An investigation has been made in the Langley low-turbulence pressure tunnel of the aerodynamic characteristics of the NACA 0012, 64(sub 2)-015, and 64(sub 3)-018 airfoil sections. Data were obtained at Mach numbers from 0.3 to that for tunnel choke, at angles of attack from -2deg to 30deg, and with the surface. of each airfoil smooth-and with roughness applied at the leading edge.The Reynolds numbers of the tests ranged from 0.8 x 10(exp 6) to 4.4 x 10(exp 6). The results are presented as variations of lift, drag, and quarter-chord pitching-moment coefficients with Mach number.
Date: 1954?
Creator: Critzos, Chris C.
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at high speeds of full-scale propellers having Clark Y blade sections

Description: From Introduction: "The single purpose of this paper is to make available the data obtained from tests of these two Clark Y section propellers as quickly as possible with no attempt being made to analyze the results or to compare them with other high-speed-propeller test results."
Date: October 26, 1948
Creator: Johnson, Peter J
Partner: UNT Libraries Government Documents Department

Aerodynamic Characteristics at High Speeds of Full-Scale Propellers having Different Shank Designs

Description: Tests of two 10-foot-diameter two-blade propellers which differed only in shank design have been made in the Langley 16-foot high-speed tunnel. The propellers are designated by their blade design numbers, NACA 10-(5)(08)-03, which had aerodynamically efficient airfoil shank sections, and NACA l0-(5)(08)-03R which had thick cylindrical shank sections typical of conventiona1 blades, The propellers mere tested on a 2000-horsepower dynamometer through a range of blade-angles from 20deg to 55deg at various rotational speeds and at airspeeds up to 496 miles per hour. The resultant tip speeds obtained simulate actual flight conditions, and the variation of air-stream Mach number with advance ratio is within the range of full-scale constant-speed propeller operation. Both propellers were very efficient, the maximum envelope efficiency being approximately 0,95 for the NACA 10-(5)(08)-03 propeller and about 5 percent less for the NACA 10-(5)(08)-03R propeller. Based on constant power and rotational speed, the efficiency of the NACA 10-(05)(08)-03 propeller was from 2.8 to 12 percent higher than that of the NACA 10-(5)(08)-03R propeller over a range of airspeeds from 225 to 450 miles per hour. The loss in maximum efficiency at the design blade angle for the NACA 10-(5)(08)-03 and 10-(5)(08)-03R propellers vas about 22 and 25 percent, respectively, for an increase in helical tip Mach number from 0.70 to 1.14.
Date: February 13, 1947
Creator: Maynard, Julian D.
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at Mach number 4.04 of a rectangular wing of aspect ratio 1.33 having a 6-percent-thick circular-arc profile and a 30-percent-chord full-span trailing-edge flap

Description: From Introduction: "The present report gives results at a Mach number of 4.04 of the part of the program concerned with flap controls at Mach numbers from 1.62 to 6.9."
Date: May 29, 1953
Creator: Dunning, Robert W & Ulmann, Edward F
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at subcritical and supercritical Mach numbers of two airfoil sections having sharp leading edges and extreme rearward positions of maximum thickness

Description: From Introduction: "A 12-percent-chord-thick wedge section and a reversed NACA 0012 section were chosen for these tests as they are representative of sections having no boat tailing and appreciable boat tailing (i.e., blunt and rounded trailing edges, respectively), and the results of this investigation are compared with those obtained from a previous investigation of the NACA 0012 section. Conclusions are drawn regarding the relative merits of the two unconventional sections and the conventional section in transonic speed range."
Date: November 6, 1947
Creator: Eggers, A J , Jr
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at subsonic and supersonic Mach numbers of a thin triangular wing of aspect ratio 2 I : maximum thickness at 20 percent of the chord

Description: From Summary: "This report presents the results of a wind-tunnel investigation conducted to determine the effects of Mach number on the aerodynamic characteristics of a wing of triangular plan form."
Date: November 19, 1948
Creator: Berggren, Robert E & Summers, James L
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at subsonic and supersonic Mach numbers of a thin triangular wing of aspect ratio 2 II : maximum thickness at midchord

Description: The lift, drag, and pitching-moment characteristics of a triangular wing, having an aspect ratio of 2 and a symmetrical double-wedge profile of 5-percent-chord maximum thickness at midchord, have been evaluated from wind-tunnel tests at Mach numbers from 0.50 to 0.975 and from 1.09 to 1.49 and at Reynolds numbers ranging from 0.67 to 0.85 million. The lift, drag, and pitching-moment coefficients of the triangular wing with a leading-edge sweepback of approximately 63 degrees did not exhibit the irregular variations with Mach number at high subsonic and low supersonic Mach numbers that are characteristic of unswept wings. The lift-curve slope increased steadily with Mach number below unity and declined slowly beyond the Mach number of 1.13. A substantial rise in the minimum drag coefficient occurred between Mach numbers of 0.95 and 1.20 with an associated reduction in the maximum lift-drag ratio. The aerodynamic center shifted rearward toward the centroid of area of the wing with increasing Mach number below 0.975; whereas above 1.09 it coincided with the centroid.
Date: December 3, 1948
Creator: Walker, Harold J & Berggren, Robert E
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at transonic speeds of a 69 degree delta wing with a triangular plan-form control having a skewed hinge axis and an overhang balance : transonic-bump method

Description: From Introduction: "Presented in this paper are the results of an investigation of a semispan model of a delta wing with 60^o sweepback at the leading edge which was equipped with a large triangular control having an overhang balance mounted on a skewed hinge axis. The purpose of this investigation was to determine the aerodynamic characteristics of a delta wing with a control which was designed to provide aerodynamic balance at zero control deflection based on the span load distribution of reference 1."
Date: February 6, 1951
Creator: Wiley, Harleth G
Partner: UNT Libraries Government Documents Department

Aerodynamic characteristics at transonic speeds of a tapered 45 degree sweptback wing of aspect ratio 3 having a full-span flap type of control with overhang balance : transonic-bump method

Description: From Introduction: "This paper presents the aerodynamic characteristics of low-aspect-ratio sweptback wing having a full-span flap type of control employing an overhanging balance of 50 percent of the flap chord.The main purpose of this investigation was to determine if overhang balances are an effective means of reducing the hinge moments of flap type of controls at transonic speeds."
Date: January 25, 1952
Creator: Lockwood, Vernard E & Hagerman, John R
Partner: UNT Libraries Government Documents Department