National Advisory Committee for Aeronautics (NACA) - 533 Matching Results

Search Results

Additional design charts relating to the stalling of tapered wings

Description: From Introduction: "The present report, therefore, may be considered a supplement to reference 1. The combined scope of the stall charts of reference 1, designated A, and of the present work, designated B, is summarized in the following table: For the wing with root thickness ratio to 18 was also investigated.
Date: January 1943
Creator: Harmon, Sidney M
Partner: UNT Libraries Government Documents Department

Aerodynamic tests of a full-scale TBF-1 aileron installation in the Langley 16-foot high-speed tunnel

Description: From Summary: "This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds."
Date: December 1944
Creator: Becker, John V & Korycinski, Peter F
Partner: UNT Libraries Government Documents Department

Air-consumption parameters for automatic mixture control of aircraft engines

Description: From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."
Date: September 1944
Creator: Shames, Sidney J
Partner: UNT Libraries Government Documents Department

Airfoil-contour modifications based on (epsilon)-curve method of calculating pressure distribution

Description: From Introduction: "Certain alternations of a qualitative nature may be performed in spite of the fact that a pressure change cannot be prescribed. It is the purpose of this paper to indicate a method by which qualitative alternation may be performed. It will be noted that the present method of contour modification will serve the intended purpose of the inverse method."
Date: July 1, 1944
Creator: Theodorsen, Theodore
Partner: UNT Libraries Government Documents Department

Airspeed fluctuations as a measure of atmospheric turbulence

Description: From Introduction: "Increments in structural loads due to atmospheric turbulence can be accurately expressed in terms of flight speed and effective gust velocities (reference 4). Data from which the effective gust velocities could be computed were also obtained during the flights of the XC-35 airplane. These data have been used to determine the significance of the fluctuations in the pilot's indicated-airspeed readings in relation to structural loads to due to atmospheric turbulence."
Date: July 1945
Creator: Tolefson, H B
Partner: UNT Libraries Government Documents Department

Altitude rating of electrical apparatus

Description: From Introduction: "This paper studies the effect of altitude on the ratings of rotating electric machines and after determining the fundamental principles involved, discusses these in relation to the application of such machines in modern aircraft."
Date: January 1943
Creator: Lebenbaum, Paul, Jr
Partner: UNT Libraries Government Documents Department

Aluminum-zinc-magnesium-copper casting alloys

Description: From Introduction: "This paper contains data on the mechanical properties of sand-cast test bars having a considerable range in zinc, magnesium, and copper content and more detailed data on the properties and foundry characteristics of an aluminum-zinc-magnesium-copper alloy having a preferred composition for high strength and ductility."
Date: July 1941
Creator: Kempf, L. W.
Partner: UNT Libraries Government Documents Department

Analysis of a thermal ice-prevention system for wing leading-edge landing-light installations

Description: From Introduction: "A typical ice formation on a wing leading-edge-type light installation is shown in figure 1. Although the primary purpose of this analytic investigation was to determine the practicability of providing a landing-light thermal ice-prevention system which could be incorporated with the wing leading-edge thermal ice-prevention system of the B-17 F airplane, the analysis has been developed in a general form for future application to similar deigns. "
Date: January 1944
Creator: Hillendahl, Wesley H
Partner: UNT Libraries Government Documents Department

Analysis of Effect of Rolling Pull-Outs on Wing and Aileron Loads of a Fighter Airplane

Description: An analysis was made to determine the effect of rolling pull-out maneuvers on the wing and aileron loads of a typical fighter airplane, the P-47B. The results obtained indicate that higher loads are imposed upon wings and ailerons because of the rolling pull-out maneuver, than would be obtained by application of the loading requirements to which the airplane was designed. An increase of 102 lb or 15 percent of wing weight would be required if the wing were designed for rolling pull-out maneuver. It was also determined that the requirements by which the aileron was originally designed were inadequate.
Date: March 1946
Creator: Pearson, Henry A. & Aiken, William S.
Partner: UNT Libraries Government Documents Department

Analysis of factors affecting net lift increment attainable with trailing-edge split flaps on tailless airplanes

Description: From Introduction: "The lift increments of different flap arrangements were determined by the method of reference 1 with a simple chord correction factor being applied. This procedure is somewhat similar in basic principles to the method of reference 2. The accuracy of the present method was determined by calculating by means of this method the lift and moment increments of flaps on 10 different finite wing-flap combinations for which wind-tunnel data were available."
Date: September 1944
Creator: Maggin, Bernard
Partner: UNT Libraries Government Documents Department

An analysis of life expectancy of airplane wings in normal cruising flight

Description: From Summary: "The independent variables considered in the analysis included stress-concentration factor, stress-load relation, wing loading, design and cruising speeds, design gust velocity, and airplane size. Several methods for estimating fatigue life from gust frequencies are discussed."
Date: July 1945
Creator: Putnam, Abbott A
Partner: UNT Libraries Government Documents Department

The analysis of strains indicated by multiple-strand resistance-type wire strain gages used as rosettes

Description: From Summary: "Methods are given for making the necessary corrections to the strains indicated by multiple-strand resistance-type wire strain gages used singly or as rosettes to measure strains at an angle to the principal strain. The results of tests to determine the validity of the methods of correction are reported."
Date: January 1, 1943
Creator: Dow, Norris F
Partner: UNT Libraries Government Documents Department

An analysis of the skipping characteristics of some full-size flying boats

Description: From Introduction: "The purpose of this report is to gather together in one place information on the skipping characteristics of number of flying boats. A graph showing the influence of the hull form on the skipping characteristics is given which should be useful in laying out the proportions of the hull in preliminary design to insure good landing behavior."
Date: January 1946
Creator: Locke, F. W. S., Jr.
Partner: UNT Libraries Government Documents Department

An analytical study of wing and tail loads associated with an elevator deflection

Description: From Introduction: "The present paper covers step 1 of the outlined investigation, includes methods of computing the variation of wing and tail loads, and gives numerical results of the application of the theory to the BT-9B airplane. Finally, theoretical formulas are developed and charts are given for computing the maximum increments of wing load, the down-tail load, and the up-tail load following a given elevator displacement."
Date: June 1941
Creator: Garvin, J B
Partner: UNT Libraries Government Documents Department

Application of a numerical procedure to stress analysis of stringer-reinforced panels

Description: From Introduction: "In the present paper a numerical procedure for the stress analysis of flat-sheet and stringer combinations of arbitrary construction and loading is presented and applied to axially loaded panels and to the reinforced covers of box beams."
Date: March 1945
Creator: Kempner, Joseph
Partner: UNT Libraries Government Documents Department