OCH Strap Model Test

PDF Version Also Available for Download.

Description

The OCH Model was stacked using the appropriate spacers between each absorber plate. Steel bars measuring 3-inch wide by 1/4-inch thick were welded, using 1/8-inch fillet weld, along all the corner edges, except the outer radius edges. On the outer radius, the straps were bolted to the end plates and to plates 9 and 17. The straps on the outer radius were also set in towards the center by approximately 3-inches. The spacers were then knocked out. Twelve strain gauges were mounted on the model. See figure 1 and the OCH strap Model log book for locations. Each rosette was ... continued below

Physical Description

55 pages

Creation Information

Weber, K. August 26, 1987.

Context

This report is part of the collection entitled: Office of Scientific & Technical Information Technical Reports and was provided by UNT Libraries Government Documents Department to Digital Library, a digital repository hosted by the UNT Libraries. More information about this report can be viewed below.

Who

People and organizations associated with either the creation of this report or its content.

Author

Publisher

Provided By

UNT Libraries Government Documents Department

Serving as both a federal and a state depository library, the UNT Libraries Government Documents Department maintains millions of items in a variety of formats. The department is a member of the FDLP Content Partnerships Program and an Affiliated Archive of the National Archives.

Contact Us

What

Descriptive information to help identify this report. Follow the links below to find similar items on the Digital Library.

Description

The OCH Model was stacked using the appropriate spacers between each absorber plate. Steel bars measuring 3-inch wide by 1/4-inch thick were welded, using 1/8-inch fillet weld, along all the corner edges, except the outer radius edges. On the outer radius, the straps were bolted to the end plates and to plates 9 and 17. The straps on the outer radius were also set in towards the center by approximately 3-inches. The spacers were then knocked out. Twelve strain gauges were mounted on the model. See figure 1 and the OCH strap Model log book for locations. Each rosette was centered in the gap between two absorber plates. The finite element plate model can predict the primary deformations of the OH module in both the cantilever and crushing modes to within 11% of the measured values. The primary stresses away from the support plate for the cantilever mode can be predicted to within 13% by this model. Near the support plate where large shear stresses exists, ANSYS will overpredict the measured stresses substantially. This is probably due to the models inherent inability to allow for shear stress concentrations at the welds. The same over-prediction was seen in the side straps during the OH crush test comparison and is probably attributable to the high shear force in this mode. The simple finite element plate model will provide suitable model of OH module stiffness for use in the analysis of the module assembly. The calculation of shear stresses can be improved by applying the ANSYS calculated inter-element forces to traditional weld strength calculations

Physical Description

55 pages

Language

Item Type

Identifier

Unique identifying numbers for this report in the Digital Library or other systems.

  • Report No.: FERMILAB-D0-EN-108
  • Grant Number: AC02-07CH11359
  • DOI: 10.2172/1030711 | External Link
  • Office of Scientific & Technical Information Report Number: 1030711
  • Archival Resource Key: ark:/67531/metadc833663

Collections

This report is part of the following collection of related materials.

Office of Scientific & Technical Information Technical Reports

Reports, articles and other documents harvested from the Office of Scientific and Technical Information.

Office of Scientific and Technical Information (OSTI) is the Department of Energy (DOE) office that collects, preserves, and disseminates DOE-sponsored research and development (R&D) results that are the outcomes of R&D projects or other funded activities at DOE labs and facilities nationwide and grantees at universities and other institutions.

What responsibilities do I have when using this report?

When

Dates and time periods associated with this report.

Creation Date

  • August 26, 1987

Added to The UNT Digital Library

  • May 19, 2016, 3:16 p.m.

Description Last Updated

  • Aug. 30, 2016, 6:16 p.m.

Usage Statistics

When was this report last used?

Yesterday: 0
Past 30 days: 0
Total Uses: 3

Interact With This Report

Here are some suggestions for what to do next.

Start Reading

PDF Version Also Available for Download.

International Image Interoperability Framework

IIF Logo

We support the IIIF Presentation API

Weber, K. OCH Strap Model Test, report, August 26, 1987; Batavia, Illinois. (digital.library.unt.edu/ark:/67531/metadc833663/: accessed October 17, 2018), University of North Texas Libraries, Digital Library, digital.library.unt.edu; crediting UNT Libraries Government Documents Department.