UNT Libraries Government Documents Department - 1,563 Matching Results
Search Results
- Accident-Severity Rates For Certain Metal Mines
- Report issued by the U.S. Bureau of Mines on the severity of accidents in the metal-mine industry. 34 metal-mines documented the number and severity of all accidents over the course if one calendar year. This report includes tables.
- Acid Processes for the Extraction of Alumina
- Report presenting the Bureau of Mines' investigation into acid processes of extracting alumina. The paper discusses the sulphuric acid processes and other work with hydrochloric and nitric acids so that the comparative advantages can be appreciated.
- Adaptation of aeronautical engines to high altitude flying
- Report discussing Issues and techniques relative to the adaptation of aircraft engines to high altitude flight. Covered here are the limits of engine output, modifications and characteristics of high altitude engines, the influence of air density on the proportions of fuel mixtures, methods of varying the proportions of fuel mixtures, the automatic prevention of fuel waste, and the design and application of air pressure regulators to high altitude flying. Summary: 1. Limits of engine output. 2. High altitude engines. 3. Influence of air density on proportions of mixture. 4. Methods of varying proportions of mixture. 5. Automatic prevention of fuel waste. 6. Design and application of air pressure regulators to high altitude flying.
- Aerial Convention of October 13, 1919
- The aerial convention delegates are listed as well as the set of rules that were developed during the session.
- Aerial navigation by dead reckoning
- Report discussing the problem to be solved, as presented to the pilot or observer of an aircraft, is as follows: The aircraft starting from A must land at B, the only data being the speed of the airplane, the altitude and the orientation D of the course. The above data would be amply sufficient, were it not for the fact that the airplane is constantly subjected to a wind of variable direction and strength.
- Aerial navigation : on the problem of guiding aircraft in a fog or by night when there is no visibility
- Report discussing the use of magnetic fields and wire to navigate aircraft in conditions of poor visibility is presented. This field may be considered to be derived from a double lemniscate, considered in the particular case where the origin is a double point formed from the magnetic field of the slack wire, from the field produced by the return currents and from the field due to the currents induced in the conducting mass. These fields are dephased in two ways, one in the direction of the wire, the other in a direction perpendicular to it.
- Aerial photography : obtaining a true perspective
- Report discussing a demonstration was given within the last few days at the British Museum by Mr. J. W. Gordon, author of "Generalized Linear Perspective" (Constable and Co.), a work describing a newly-worked-out system by which photographs can be made available for the purpose of exactly recording the dimensions of the objects photographed even when the objects themselves are presented foreshortened in the photograph.
- Aerial Transportation
- Report discussing the origin of air traffic dates from the war. The important development of aeronautic industries and the progress made in recent years, under the impelling force of circumstances, rendered it possible, after the close of hostilities, to consider the practical utilization of this new means of economic expansion.
- Aero Dopes and Varnishes
- Report discussing before proceeding to discuss the preparation of dope solutions, it will be necessary to consider some of the essential properties which should be possessed of a dope film, deposited in and on the surface of an aero fabric. The first is that it should tighten the material and second it should withstand weathering.
- Aerodynamic Characteristics of Aerofoils
- The object of this report is to bring together the investigations of the various aerodynamic laboratories in this country and Europe upon the subject of aerofoils suitable for use as lifting or control surfaces on aircraft. The data have been so arranged as to be of most use to designing engineers and for the purposes of general reference. The absolute system of coefficients has been used, since it is thought by the National Advisory Committee for Aeronautics that this system is the one most suited for international use, and yet is one for which a desired transformation can be easily made. For this purpose a set of transformation constants is included in this report.
- Aerodynamic Characteristics of Aerofoils 2: Continuation of Report No. 93
- "This collection of data on aerofoils has been made from the published reports of a number of the leading aerodynamic laboratories of this country and Europe. The information which was originally expressed according to the different customs of the several laboratories is here presented in a uniform series of charts and tables suitable for the use of designing engineers and for purposes of general reference. The absolute system of coefficients has been used, since it is thought by the National Advisory Committee for Aeronautics that this system is the one most suited for international use, and yet is one for which a desired transformation can be easily made" (p. 423).
- Aerodynamic Characteristics of Aircraft With Reference to Their Use
- Report discussing economic and design characteristics are examined in the design of airplanes and airships.
- Aerodynamic Characteristics of Airfoils 3: Continuation of Reports Nos. 93 and 124
- "This collection of data on airfoils has been made from the published reports of a number of the leading aerodynamic laboratories of this country and Europe. The information which was originally expressed according to the different customs of the several laboratories is here presented in a uniform series of charts and tables suitable for the use of designing engineers and for purposes of general reference. The absolute system of coefficients has been used, since it is thought by the National Advisory Committee for Aeronautics that this is the one most suited for international use and yet is one for which a desired transformation can be easily made" (p. 397).
- Aerodynamic Characteristics of Airfoils 4: Continuation of Reports Nos. 93, 124, and 182
- This collection of data on airfoils has been made from the published reports of a number of the leading Aerodynamic Laboratories of this country and Europe. The information which was originally expressed according to the different customs of the several laboratories is here presented in a uniform series of charts and tables suitable for the use of designing engineers and for purposes of general reference. The authority for the results here presented is given as the name of the laboratory at which the experiments were conducted, with the size of the model, wind velocity, and year of test.
- Aerodynamic Characteristics of Airfoils 5: Continuation of Reports Nos. 93, 124, 182, and 244
- "This collection of data on airfoils has been made from published reports of a number of the leading aerodynamic laboratories of this country and Europe. The information which was originally expressed according to the different customs of the several laboratories is here presented in a uniform series of charts and tables suitable for the use of designing engineers and for purposes of general reference. The authority for the results here presented is given as the name of the laboratory at which the experiments were conducted, with the size of the model, wind velocity, and year of tests" (p. 139).
- Aerodynamic characteristics of airfoils at high speeds
- From Summary: "This report deals with an experimental investigation of the aerodynamical characteristics of airfoils at high speeds. Lift, drag, and center of pressure measurements were made on six airfoils of the type used by the air service in propeller design, at speeds ranging from 550 to 1,000 feet per second. The results show a definite limit to the speed at which airfoils may efficiently be used to produce lift, the lift coefficient decreasing and the drag coefficient increasing as the speed approaches the speed of sound. The change in lift coefficient is large for thick airfoil sections (camber ratio 0.14 to 0.20) and for high angles of attack. The change is not marked for thin sections (camber ratio 0.10) at low angles of attack, for the speed range employed. At high speeds the center of pressure moves back toward the trailing edge of the airfoil as the speed increases. The results indicate that the use of tip speeds approaching the speed of sound for propellers of customary design involves a serious loss in efficiency."
- The aerodynamic characteristics of seven frequently used wing sections at full Reynolds number
- This report contains the aerodynamic properties of the wing sections U.S.A. 5, U.S.A. 27, U.S.A. 35 A, U.S.A. 35 B, Clark Y, R.A.F. 15, and Gottingen 387, as determined at various Reynolds numbers up to an approximately full scale value in the variable density wind tunnel of the National Advisory Committee for Aeronautics. It is shown that the characteristics of the wings investigated are affected greatly and in a somewhat erratic manner by variation of the Reynolds number. In general there is a small increase in maximum lift and an appreciable decrease in drag at all lifts.
- Aerodynamic Characteristics of Thin Empirical Profiles and Their Application to the Tail Surfaces and Ailerons of Airplanes
- From Introduction: "The increasing use of airplane wings equipped with ailerons and the importance of knowing the aerodynamic characteristics of tail units (empennages) provided with movable parts (rudders and elevators) impart some interest to the so-called "empirical profiles." For this purpose we thought best to employ the method proposed by Munk for the approximate theoretical study of thin, slightly curved profiles, assimilable, from an aerodynamic view-point, to their mean camber line."
- Aerodynamic Computation of Gliders
- From Introduction: "In the following discussion, a knowledge of the theoretical principles of airplane construction is assumed, as presented in detail by Vogt and Lippisch in Nos. 7 and 10-19 of the 1919 volume of this publication. A few quantities will however be otherwise designated, in accordance with the Gottingen symbols."
- The Aerodynamic Forces on Airship Hulls
- "This report describes the new method for making computations in connection with the study of rigid airship, which was used in the investigation of the navy's ZR-1 by the special subcommittee of the National Advisory Committee for Aeronautics appointed for this purpose. It presents the general theory of the air forces on airship hulls of the type mentioned, and an attempt has been made to develop the results from the very fundamentals of mechanics without reference to some of the modern highly developed conceptions, which may not yet be thoroughly known to readers uninitiated into modern aerodynamics, and which may, perhaps, for all time remain restricted to a small number of specialists" (p. 5).
- Aerodynamic Laboratory at Cuatro Vientos
- This report presents a listing of the many experiments in aerodynamics taking place at Cuatro Vientos. Some of the studies include: testing spheres, in order to determine coefficients; mechanical and chemical tests of materials; and various tests of propeller strength and flexibility.
- Aerodynamic laboratory at Cuatro Vientos
- This report presents a description of the design of the Cuatro Vientes wind tunnel.
- The Aerodynamic Laboratory of the Belgian "Service Technique De L'Aeronautique"
- This report provides a description of the wind tunnel housing and motors at the Belgian Service Technique de L'Aeronautique.
- The aerodynamic plane table
- This report gives the description and the use of a specially designed aerodynamic plane table.
- The aerodynamic properties of thick aerofoils suitable for internal bracing
- From Introduction: "The object of this investigation was to determine the characteristics of various types of wings having sufficient depth to entirely inclose the wing bracing, and also to provide data for the further design of such sections. Results of the investigation of the following subjects are given: (1) effect of changing the upper and lower camber of thick aerofoils of uniform section; (2) effect of thickening the center and thinning the tips of a thin aerofoil; (3) effect of adding a convex lower surface to a tapered section; (4) effect of changing the mean thickness with constant center and tip sections; and (5) effect of varying the chord along the span."
- The Aerodynamic Properties of Thick Airfoils 2
- "This investigation is an extension of NACA report no. 75 for the purpose of studying the effect of various modifications in a given wing section, including changes in thickness, height of lower camber, taper in thickness, and taper in plan form with special reference to the development of thick, efficient airfoils. The method consisted in testing the wings in the NACA 5-foot wind tunnel at speeds up to 50 meters (164 feet) per second while they were being supported on a new type of wire balance. Some of the airfoils developed showed results of great promise" (p. 521).
- Aerodynamic theory and test of strut forms. Part I
- This report presents the first part of a two part study made under this title. In this part the symmetrical inviscid flow about an empirical strut of high service merit is found by both the Rankine and the Joukowsky methods. The results can be made to agree as closely as wished. Theoretical stream surfaces as well as surfaces of constant speed and pressure in the fluid about the strut are found. The surface pressure computed from the two theories agrees well with the measured pressure on the fore part of the model but not so well on the after part. From the theoretical flow speed the surface friction is computed by an empirical formula. The drag integrated from the friction and measured pressure closely equals the whole measured drag. As the pressure drag and the whole drag are accurately determined, the friction formula also appears trustworthy for such fair shapes. (author).
- Aerodynamic theory and tests of strut forms 2
- This report presents the second of two studies under the same title. In this part five theoretical struts are developed from distributed sources and sinks and constructed for pressure and resistance tests in a wind tunnel. The surface pressures for symmetrical inviscid flow are computed for each strut from theory and compared with those found by experiment. The theoretical and experimental pressures are found to agree quantitatively near the bow, only qualitatively over the suction range, the experimental suctions being uniformly a little low, and not at all near the stern.
- The Aerodynamical Laboratory of the Vienna Technical High School
- Report presenting a description of the aerodynamics laboratory of the Vienna Technical High School. The main focus of this report is detailing some of the accomplishments that the laboratory has made.
- Aerodynamics and Ballistics
- Ballistics is a science hundreds of years old and this report is an attempt to show how these older principles can be used in the newer science of aerodynamics.
- Aeromechanical Experimentation (Wind Tunnel Tests)
- The following report endeavors to show that aeromechanical experimentation has become an important aid to theory. Experiments can be tried with separate parts of airplanes or with models of whole airplanes, with propellers, and with anything else that comes into contact with moving air.
- Aeronautic Instruction in Germany
- This report contains a list of the courses relating to aeronautics announced in Germany, both in the technical high schools and in the universities.
- Aeronautic Instruments
- "The development of aeronautic instruments. Vibrations, rapid changes of the conditions of flight and of atmospheric conditions, influence of the air stream all call for particular design and construction of the individual instruments. This is shown by certain examples of individual instruments and of various classes of instruments for measuring pressure, change of altitude, temperature, velocity, inclination and turning or combinations of these" (p. 1).
- Aeronautic instruments. Section 1: general classification of instruments and problems including bibliography
- This report is intended as a technical introduction to the series of reports on aeronautic instruments. It presents a discussion of those subjects which are common to all instruments. First, a general classification is given, embracing all types of instruments used in aeronautics. Finally, a classification is given of the various problems confronted by the instrument expert and investigator. In this way the following groups of problems are brought up for consideration: problems of mechanical design, human factor, manufacturing problems, supply and selection of instruments, problems concerning the technique of testing, problems of installation, problems concerning the use of instruments, problems of maintenance, and physical research problems. This enumeration of problems which are common to instruments in general serves to indicate the different points of view which should be kept in mind in approaching the study of any particular instrument.
- Aeronautic instruments. Section 2: altitude instruments
- This report is Section two of a series of reports on aeronautic instruments (Technical Report nos. 125 to 132, inclusive). This section discusses briefly barometric altitude determinations, and describes in detail the principal types of altimeters and barographs used in aeronautics during the recent war. This is followed by a discussion of performance requirements for such instruments and an account of the methods of testing developed by the Bureau of Standards. The report concludes with a brief account of the results of recent investigations. For accurate measurements of altitude, reference must also be made to thermometer readings of atmospheric temperature, since the altitude is not fixed by atmospheric pressure alone. This matter is discussed in connection with barometric altitude determination.
- Aeronautic Instruments Section 3: Aircraft Speed Instruments
- Part 1 contains a discussion and description of the various types of air speed measuring instruments. The authors then give general specifications and performance requirements with the results of tests on air speed indicators at the Bureau of Standards. Part 2 reports methods and laboratory apparatus used at the Bureau of Standards to make static tests. Methods are also given of combining wind tunnel tests with static tests. Consideration is also given to free flight tests. Part 3 discusses the problem of finding suitable methods for the purpose of measuring the speed of aircraft relative to the ground.
- Aeronautic Instruments Section 4: Direction Instruments
- Part one points out the adequacy of a consideration of the steady state gyroscopic motion as a basis for the discussion of displacements of the gyroscope mounted on an airplane, and develops a simple theory on this basis. Part two describes a new type of stabilizing gyro mounted on top of a spindle by means of a universal joint, the spindle being kept in a vertical position by supporting it as a pendulum of which the bob is the driving motor. Methods of tests and the difficulties in designing a satisfactory and reliable compass for aircraft use in considered in part three. Part four contains a brief general treatment of the important features of construction of aircraft compasses and description of the principal types used.
- Aeronautic instruments. Section 5 : power plant instruments
- Part 1 gives a general discussion of the uses, principles, construction, and operation of airplane tachometers. Detailed description of all available instruments, both foreign and domestic, are given. Part 2 describes methods of tests and effect of various conditions encountered in airplane flight such as change of temperature, vibration, tilting, and reduced air pressure. Part 3 describes the principal types of distance reading thermometers for aircraft engines, including an explanation of the physical principles involved in the functioning of the instruments and proper filling of the bulbs. Performance requirements and testing methods are given and a discussion of the source of error and results of tests. Part 4 gives methods of tests and calibration, also requirements of gauges of this type for the pressure measurement of the air pressure in gasoline tanks and the engine oil pressure on airplanes. Part 5 describes two types of gasoline gauges, the float type and the pressure type.
- Aeronautic instruments. Section 6 : aerial navigation and navigating instruments
- This report outlines briefly the methods of aerial navigation which have been developed during the past few years, with a description of the different instruments used. Dead reckoning, the most universal method of aerial navigation, is first discussed. Then follows an outline of the principles of navigation by astronomical observation; a discussion of the practical use of natural horizons, such as sea, land, and cloud, in making extant observations; the use of artificial horizons, including the bubble, pendulum, and gyroscopic types. A description is given of the recent development of the radio direction finder and its application to navigation.
- Aeronautic Instruments Section 6: Oxygen Instruments
- This report contains statements as to amount of oxygen required at different altitudes and the methods of storing oxygen. The two types of control apparatus - the compressed oxygen type and the liquid oxygen type - are described. Ten different instruments of the compressed type are described, as well as the foreign instruments of the liquid types. The performance and specifications and the results of laboratory tests on all representative types conclude this report.
- Aeronautic Instruments Section 8: Recent Developments and Outstanding Problems
- This report is section VIII of a series of reports on aeronautic instruments. The preceding reports in this series have discussed in detail the various types of aeronautic instruments which have reached a state of practical development such that they have already found extensive use. It is the purpose of this paper to discuss briefly some of the more recent developments in the field of aeronautic instrument design and to suggest some of the outstanding problems awaiting solution.
- Aeronautic Insurance
- The problem of insuring the emerging commercial aeronautic industry is detailed. The author also motes that a complete solution cannot be obtained until the necessary statistics are compiled.
- Aeronautical Instruments
- Note presenting a number of instruments that can assist pilots with observing the position of the airplane. Some of the instruments include an inclinometer with stationary system of reference and an inclinometer with moving axes.
- Aeronautical Museums
- Different methods of presenting aeronautical artifacts are examined. The advantages of operating an aeronautical museum and its ability to increase public interest in aircraft are provided.
- Aeronautical Record: No. 1 (to June, 1923)
- Memorandum presenting an overview of the development of aeronautical industries and commercial aircraft as well as some of the problems that are resulting from it. Details of the aeronautical budget in various countries, organization of the air service, material exports, and airline operations are provided.
- Air Cooling: An Experimental Method of Evaluating the Cooling Effect of Air Streams on Air-Cooled Cylinders
- In this report is described an experimental method which the writer has evolved for dealing with air-cooled engines, and some of the data obtained by its means. Methods of temperature measurement and cooling are provided.
- Air-Flow Experiments
- This report describes the apparatus used to take air-flow photographs. The photographs show chiefly the spiral course of the lines of flow near the tip of the wing. They constitute therefore a visual presentation of the phenomena covered by airfoil theory.
- Air Flow Investigation for Location of Angle of Attack Head on a JN4h Airplane
- The technical staff of the NACA at Langley Field, has made a series of free flight tests with a JN4h airplane in order to find the best place for an instrument for measuring the angle of attack. A "neutral zone" was found where the air remains either at rest relative to the undisturbed air beyond the influence of the airplane, or is set in motion parallel to the motion of the airplane. This zone is about midway between the two wings and slightly in front of, or at the vertical plane through the leading edges of the wings but the exact position as well as the outlines of the zone varies considerably as the conditions of flight change.
- Air force and moment for N-20 wing with certain cut-outs
- From Introduction: "The airplane designer often finds it necessary, in meeting the requirements of visibility, to remove area or to otherwise locally distort the plan or section of an airplane wing. This report, prepared for the Bureau of Aeronautics January 15, 1925, contains the experimental results of tests on six 5 by 30 inch N-20 wing models, cut out or distorted in different ways, which were conducted in the 8 by 8 foot wind tunnel of the Navy Aerodynamical Laboratory in Washington in 1924. The measured and derived results are given without correction for vl/v for wall effect and for standard air density, p=0.00237 slug per cubic foot."
- Air force and three moments for F-5-L Seaplane
- From Introduction: "A model of the F-5-L seaplane was made, verified, and tested at 40 miles an hour in the 8' x 8' tunnel for lift and drag, also for pitching, yawing and rolling moments. Subsequently, the yawing moment test was repeated with a modified fin. The results are reported without VL scale correction."