You limited your search to:

  Partner: UNT Libraries Government Documents Department
 Decade: 1940-1949
 Year: 1943
 Collection: Technical Report Archive and Image Library
The analysis of strains indicated by multiple-strand resistance-type wire strain gages used as rosettes

The analysis of strains indicated by multiple-strand resistance-type wire strain gages used as rosettes

Date: January 1, 1943
Creator: Dow, Norris F
Description: None
Contributing Partner: UNT Libraries Government Documents Department
Analysis of the High-Altitude Cooling of the Ranger SGV-770 D-4 Engine in the Bell XP-77 Airplane

Analysis of the High-Altitude Cooling of the Ranger SGV-770 D-4 Engine in the Bell XP-77 Airplane

Date: October 1, 1943
Creator: Nielsen, Jack N.
Description: No abstract available.
Contributing Partner: UNT Libraries Government Documents Department
Analysis of wind-tunnel stability and control tests in terms of flying qualities in full-scale airplanes

Analysis of wind-tunnel stability and control tests in terms of flying qualities in full-scale airplanes

Date: October 1, 1943
Creator: Kayten, Gerald G
Description: None
Contributing Partner: UNT Libraries Government Documents Department
Annual Report of Research and Technologic Work on Coal: Fiscal Year 1942

Annual Report of Research and Technologic Work on Coal: Fiscal Year 1942

Date: May 1943
Creator: Fieldner, Arno Carl
Description: Report issued by the U.S. Bureau of Mines discussing studies over the research and technology of coal during 1942. As stated in the introduction, "the annual reports of the research and technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal, of which the present report is the seventh, are intended to be brief summaries of progress" (p. 4). This report includes tables, illustrations, and photographs.
Contributing Partner: UNT Libraries Government Documents Department
Antiknock effectiveness of xylidines in small-scale engines

Antiknock effectiveness of xylidines in small-scale engines

Date: August 1, 1943
Creator: Meyer, Carl L
Description: None
Contributing Partner: UNT Libraries Government Documents Department
An approximate method of shear-lag analysis for beams loaded at right angles to the plane of symmetry of the cross section

An approximate method of shear-lag analysis for beams loaded at right angles to the plane of symmetry of the cross section

Date: September 1, 1943
Creator: Brilmyer, Harold J
Description: None
Contributing Partner: UNT Libraries Government Documents Department
Bearing strengths of bare and alclad XA75S-T and 24S-T81 aluminum alloy sheet

Bearing strengths of bare and alclad XA75S-T and 24S-T81 aluminum alloy sheet

Date: December 1, 1943
Creator: Moore, R L
Description: None
Contributing Partner: UNT Libraries Government Documents Department
Bearing strengths of some wrought-aluminum alloys

Bearing strengths of some wrought-aluminum alloys

Date: August 1, 1943
Creator: Moore, R L
Description: Although a number of investigations of the bearing strength of aluminum alloys have been made, the problem remains one of considerable interest to the aircraft industry. For this reason it has seemed advisable to make additional tests of the commonly used aircraft alloys in an effort to establish a better basis for the selection of allowable bearing values. Current design practice does not recognize the effect of edge distance upon bearing strengths, and for this reason edge distance was one of the principal variables considered in this investigation. The increasing emphasis being placed upon permanent set limitations makes it essential that more information on bearing yield phenomena be obtained. The object of this investigation was to determine bearing yield and ultimate strengths of the following aluminum alloy products: 17S-T, 24S-T, Alclad 24S-T, 24S-RT, 52S-0, 52S-1/2H, 52S-H, 53S-T, and 61S-T extrusions. Ratios of these bearing properties to tensile properties were also determined.
Contributing Partner: UNT Libraries Government Documents Department
Bearing tests of magnesium-alloy sheet

Bearing tests of magnesium-alloy sheet

Date: June 1, 1943
Creator: Sharp, W H
Description: Bearing tests of AM-3S, AM-52S, and AM-C57S magnesium-alloy sheet in various thicknesses and tempers were made. Bearing yield and ultimate strengths were determined and compared for various edge distances and for various ratios of loading-pin diameter to sheet thickness. Tensile strengths were determined and ratios of average bearing yield and ultimate strength to tensile strength are given. The results of the tests indicated that ultimate bearing strengths increased with edge distances up to 1.5 to 2 times the diameter of the loading pin; that ultimate bearing strengths are a function of the ratio of pin diameter to sheet thickness; and that these properties are effected only slightly by increases in edge distance greater than 1.5 diameters.
Contributing Partner: UNT Libraries Government Documents Department
The belt method for measuring pressure distribution

The belt method for measuring pressure distribution

Date: February 1, 1943
Creator: Corson, Blake W , Jr
Description: None
Contributing Partner: UNT Libraries Government Documents Department