From Introduction: "The airfoil sections tested, which differ only in thickness ratio, were the NACA 64-006, 64-008, 64-010, and 641-012. Lift, drag, and pitching-moment data were obtained for Mach numbers of 0.3 to that for tunnel choke at angles of attack of -2^o to 31^o. The results of this investigation are reported herein."
"The over-all performance of a 16-stage axial-flow compressor was determined with various stator-blade resettings and a reduction in solidity of the rotor blades in the last three stages. It was shown that little control over the sudden change in slope of the surge-limit line at intermediate speeds was obtained with the blade modifications attempted, except that some change in speed at which the change in slope occurred could be effected by stator-blade resettings" (p. 1).
Spanwise lift distributions have been calculated for nineteen unswept wings with various aspect ratios and taper ratios and with a variety of angle-of-attack or twist distributions, including flap and aileron deflections, by means of the Weissinger method with eight control points on the semispan. Also calculated were aerodynamic influence coefficients which pertain to a certain definite set of stations along the span, and several methods are presented for calculating aerodynamic influence functions and coefficients for stations other than those stipulated. The information presented in this report can be used in the analysis of untwisted wings or wings with known twist distributions, as well as in aeroelastic calculations involving initially unknown twist distributions.
Report presenting a cascade-general-momentum theory method for calculating the operating conditions of a supersonic propeller annulus throughout the flight Mach number range. General flow patterns about the cascade and adjustments to free-stream conditions are discussed.
Report presenting a transonic investigation made by the free-fall technique of a plane wing and a cambered and twisted wing, each with an aspect ratio 6, taper ratio of 0.5, and a sweepback of 45 degrees. Measurements were made of the loads on the exposed wings, pressures on the fuselage in the vicinity of the wing, and acceleration and angle of attack of the complete model.
Memorandum compiling summaries from NACA reports on fuel that were published between July 1945 and 1952. The summaries are intended to be detailed enough to eliminate the need to obtain the complete report.
An analysis is made of the factors affecting the weight-flow rate per unit frontal area of centrifugal compressors with axial-flow vaned diffusers preceded by mixed-flow vaneless sections. It is shown that, for specified inlet conditions to the impeller and vaned diffuser, the weight-flow rate is increased at the expense of pressure ratio and vice versa. Charts are presented to help the designer make a satisfactory compromise between weight-flow rate and pressure ratio. Some conclusions of the investigation are : (1) Prewhirl is of negligible value in centrifugal compressors designed for high weight-flow rates.
Report presenting an investigation to evaluate the effects of nacelles and extended split flaps on the longitudinal characteristics of a wing-fuselage-tail combination of a type believed to be suitable for long-range high-speed airplanes. Wind tunnel tests to study the effects of the nacelles and flaps were conducted at a range of Mach and Reynolds numbers. Results regarding the effects of the nacelles with the tail off, effects of tail height, effects of nacelles with the tail on, and effects of flaps are provided.
A project proposal is now under preparation for converting all areas to the alum and activated silica coagulation process, and modifying the present test installations to permanent facilities. The conversions will be designed to service increased water flows resulting from the reactor plant expansion program now under way. As an alternate to the installation of permanent facilities at the various areas, the possibility of hauling already prepared activated silica from those areas having excess capacity to those areas requiring large capital expenditures was suggested. The purpose of this study is to make an economic evaluation of the operating costs of hauling activated silica compared to the increased capital investment necessary to manufacture activated silica at various areas.
Report presenting an experimental investigation performed to determine the effect on base and forebody pressures of using a sting modified with varying length splitter plates and fins instead of a conventional sting to support a cone-cylinder body of revolution.
The object of the work performed under this contract was to investigate the possibility of gas plating copper base metal with (a) pure chromium metal from chromium hexacarbonyl vapor; (b) chromium-nickel plating from a mixture of chromium hexacarbonyl and nickel tetracarbonyl. The object of the work performed during the final month was to confirm the fact that the gas plating of chromium metal and chromium-nickel laminates free from nitrides, oxides and carbides was practical.
Report presenting an investigation to determine the effects of center-of-gravity position on the gust loads of a delta-wing model with the leading edge swept back 60 degrees. A 15-percent change in the center-of-gravity position on the mean geometric chord produced a 7.5-percent change in load for the model in a sharp-edge gust and a 35-percent change in load in a gust with a 6.5 chord gradient distance.
It is recommended that the Design Committee approve the installation of a refrigeration system in the 105-C gas circulation system for removal of moisture from the reactor following a process tube leak as was previously approved by the C-431 Project Committed. Engineering studies show that this refrigeration system is necessary to provide sufficient water removal capacity in order that the water absorbing capacity of the system furnished by the silica gel towers will not be a limit to the rate at which a reactor can be rehabilitated following a serious leak.
This report examines a uranium slug that has been produced by powder metallurgical methods and exposed in the 100-DR Pile and was deformed during pile exposure.
Report presenting load measurements using the swept-wing Bell X-5 and Douglas D-558-II research airplanes during flights in which reductions of longitudinal stability were experienced when pilots attempted to perform routine test maneuvers at moderate values of lift. Results regarding the maximum angles of attack and sideslip measured, pitching accelerations, horizontal-tail loads, wing loads, and stability deficiencies are provided.
Report presenting an investigation in the full-scale tunnel to determine the effects of a Fowler type slotted flap on the aerodynamic characteristics of a semispan 49.1 degree sweptback wing with NACA 65A006 airfoil sections streamwise, an aspect ratio of 3.78, and a taper ratio of 0.59. Results regarding the pitching-moment curve, effect of flap deflection, and lift increments are provided.
Report presenting an investigation of the performance of slurry fuels consisting of 50 percent magnesium powder in a hydrocarbon carrier in a flight-type, 6.5-inch-diameter ramjet engine mounted in a connected-pipe facility. Results regarding the slurry performance and a comparison of slurry and ethylene performance are provided.
"Neutron total cross sections for bismuth and uranium have been measured in a good geometry transmission experiment, using a time-of-flight instrumentation. The source of neutrons was the stripped deuteron beam of the 184-inch synchrocyclotron. The results are shown in Fig. 1. Uncertainties are shown in terms of standard deviations, due to counting statistics only, and to energy channel width."
This is a listing of the classified periodic and series reports originated at the Hanford Atomic Products Operation for the period 1943 to June, 1953, and of similar reports received from the Hanford Operations Office. This listing also traces the continuity of reports that have undergone title changes during this period. This has been done by cross referencing to titles previously or subsequently used. The primary grouping of these reports is according to the intervals at which they were issued, e.g., weekly, monthly, annually, etc. Within each group, the reports are arranged alphabetically by title; for each individual title a note at the right hand margin gives the inclusive dates for the period during which reports of that title were issued. Those not shown with closing date are being issued currently. Specific document numbers for each title are found in the catalogs of the 700 Area and 300 Area Classified Files. The list is intended primarily to assist Classified Files in locating periodic reports requested by Plant personnel. However, it is also hoped that it may emphasize to authors the need for retaining an established title for a periodic report. Unnecessary changes of title every few months for the same periodic report greatly complicate the problem of organizing the reports collection for reference use.
Preliminary results at high speeds indicate lower bearing temperatures, less internal bearing wear, and greater reliability of the conventional, cage-type cylindrical roller bearings than of either full-complement or special cageless roller bearings of the types investigated, although the latter bearing types have been operated successfully to DN values of 1.0 X 10 superscript 6.
A scheme was proposed whereby the third and second uranium cycle salt wastes in the Redox plant are combined, stripped, evaporated, and then returned as scrub to the first (and possibly second) cycles as scrub, operating as a dual scrub column. It is the purpose of this report to study this proposed method of back-cycling, and to investigate other methods of reducing chemical and waste storage costs.
"During the course of an investigation by the Langley Pilotless Aircraft Research Division regarding the effectiveness of spoilers and ailerons on sweptback tapered wings, it was necessary to test a given control configuration on wings of varying degrees of stiffness. In the process of conducting these tests, repeated wing failure was experienced with the weaker wing-spoiler configurations, whereas no failure occurred with any of the wing-aileron models. An investigation which was conducted by means of rocket-propelled test vehicles in free flight showed that the cause of the repeated failures was flutter of the bending-torsion type" (p. 1).
At the present time, production commitments require that each of the two dissolvers used at the Redox Plant be charged with 4.95 tons of irradiated metal every other day. After the aluminum jackets are removed from the slugs, the uranium is dissolved in three ``outs`` of 1.65 tons each. Because meteorological conditions often limit the time when the radioactive dissolver off gases may be emitted without contamination of the surrounding area, the dissolving requirements are frequently too great to maintain the required dissolver charging schedule. Unless the dissolving time cycles (or the meteorological limitations) can be reduced to assure that charging every other day can be maintained, phase 2 rates cannot be met even after activation of the third (spare) dissolver. As a means of reducing the dissolver time cycle and enabling the charging of each dissolver on alternate days throughout the year, a proposal was submitted that each dissolver charge be dissolved in two cuts of 2.475 tons each. This report presents the results of the plant test to determine the operational feasibility and relative merits of this proposal. Moreover, the information obtained may be used on a supplemental basis for the design of the Purex Plant dissolvers. 3 refs., 3 tabs.
In the separation of mixtures of radioactive iron and cobalt from neutron irradiated targets and in the removal of iron from cobalt targets for cyclotron production of radioiron, it is desirable to have a method superior to extraction from isopropyl ether in efficiency and ease of manipulation. Recent studies by Moore and Kraus on the separation of cobalt and nickel and on the behavior of iron in hydrochloric acid on Dowex-l resin in relation to the selective adsorption of chloride complexes of these elements have suggested the use of resin for the separation of iron and cobalt.
Recent studies on the separation of cobalt and nickel and on the behavior of iron in hydrochloric acid on Dowex-1 resin in relation to the selective adsorption of chloride complexes of these elements have suggested the use of resin for the separation of iron and cobalt.
On January 12, 1953, an explosion occurred in the Savannah River pilot plant which has been used since November, 1951 by du Pont personnel to train operators and to test equipment for their new Purex production plant. The explosion occurred in an evaporator in which a uranyl nitrate solution containing some organics was being concentrated to a high degree to remove nitric acid. This memorandum reviews the facts surrounding the incident as obtained from the official Preliminary Technical Report'', and by talking to du Pont personnel. These facts are interpreted as fast as possible and the current design for the Hanford Purex production plant is re-evaluated in the light of these data.
This dialog allows you to filter your current search.
Each of the Collections listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the World Regions listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Countries listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Months listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.