UNT Libraries Government Documents Department - 46 Matching Results

Search Results

Results: 1 - 24 next
open access

Adiabatic Injection

Description: From introduction comments: The present analysis is intended to examine the relations for "adiabatic" injection in general from a different point of view.
Date: September 22, 1955
Creator: Linlor, William I., 1915-
Item Type: Refine your search to only Report
open access

The Ductility of Brazed Stainless Steel Joints

Description: Abstract: "The ductility of Type 310 stainless steel T-joints brazed with GE-62 brazing alloy was measured at room temperatures 1200, 1650, and 1800 F. The measure of ductility was taken as the plastic axial strain required to crack braze fillets in T-section tensile specimens. At elevated temperatures, the ductility of as-brazed joints approximated that of the stainless steel, but at room temperature the brazed joints had only one-tenth the ductility of the base metal. Annealing for 16 hr at 1… more
Date: July 8, 1953
Creator: Saller, Henry A.; Stacy, J. T. & Eddy, N. S.
Item Type: Refine your search to only Report
open access

The Effects of Chemical Impurities on the Quality of Rolled Uranium Rod

Description: Abstract: "Thirty-four uranium ingots containing controlled amounts of carbon, nitrogen, and Mgl2 slag were cast, rolled, and examined to investigate the relation between these impurities and the quality of the rolled rod. Carbon in concentrations up to 1400 ppm and nitrogen up to 170 ppm, either singly or in combination, had no significant effect on the number of defects observed in the rolled rod. The quality of the rods, however decreased with increasing amount of slag necessary to cause obs… more
Date: October 1, 1954
Creator: Saller, Henry A.; Keeler, J. R. & Cuddy, L. J.
Item Type: Refine your search to only Report
open access

Electroplated Metals on Uranium for Aluminum Cladding

Description: Abstract: "Aluminum-clad nickel-plated uranium is corrosion resistant in boiling water. Samples with intentional defects in the aluminum-nickel clodding layers, after testing for more than 300 hr. showed no sign of rapid failure. The study of electroplated metals on uranium for aluminum cladding has defined the effects of several processing variables on the corrosion resistance. The quality of the uranium and the quality of the aluminum-nickel bond were important. Heat treatment and vacuum outg… more
Date: May 4, 1955
Creator: Beach, John G.; Schickner, William C.; Hopkinson, Dolores. & Faust, Charles L.
Item Type: Refine your search to only Report
open access

The Elimination of Microwave Reflections

Description: Abstract: "The reflections of microwaves from the walls of a plasma-containing vessel are studied. The probable cause of the reflections is discussed, and several suggestions are made for eliminating the reflections from the waveguide in the vessel and particularly from the pyrex vessel wall and copper tubing surrounding the pyrex. Quarter-wave-thick carbon-filled plastics or glasses having a very low vapor pressure room most promising when placed inside the pyrex cylinder. BaTiO3 appears to be… more
Date: February 1, 1955
Creator: Beard, David
Item Type: Refine your search to only Report
open access

Energetic Neutral Injection into Thermonuclear Machines

Description: Abstract: "A scheme is discussed in which D+ ions would be accelerated to about 100 kev in a conventional accelerator, then be sent through a gas target frmo which about half the ions would emerge neutral with very little scattering or energy loss; the neutral beam would then cross into a magnetic field and part of the atoms would be ionized and trapped by colliding with the already trapped ions. The smallest mirror machine with a central field of 30-40 kilogauss, 2;1 mirror ratio and β = 01 to… more
Date: August 10, 1955
Creator: Lauer, Eugene J.
Item Type: Refine your search to only Report
open access

Energy Transfer Between Modified Maxwell Distributions

Description: Abstract: "A particularly conventional modified form of Maxwell distribution is chosen. The modified expressions for (a) the energy transfer from the ions to the electrons in a plasma and (b) the brehmestrahlung from the electrons are calculated. Using the expressions some possible steady-state conditions for the ion and electron gases are derived and compared with those for the usual Maxwell distributions."
Date: September 20, 1956
Creator: Greyber, Howard D. & Bing, G.
Item Type: Refine your search to only Report
open access

Evaluation and Consolidation of Electrolytic Thorium

Description: Abstract: "Sound, fabricable ingots of thorium were produced by triple are melting of electrolytic thorium. Consumable electrodes were fabricated by tack welding of cold-pressed and vacuum-sintered bars of the granular thorium electrodeposited from a molten-salt bath. The hydrogen content of the electrodeposited material was reduced from 80 to 4 ppm by vacuum sintering at 1250 C at pressures below 1 x 10-(-3) mm of mercury. Both sodium and chlorine content were reduced during melting; sodium fr… more
Date: June 15, 1955
Creator: Saller, Henry A.; Dickerson, Ronald F. & Foster, Ellis L.
Item Type: Refine your search to only Report
open access

An Exact Analysis of Limited Plane Plasma in a Magnetic Field

Description: Introduction: "Prior analyses of a plasma in a magnetic field have been limited, as far as the writer is aware, to cases in which the relative change in field over the orbital distance and the relative change in ion concentration are both small, or in which the relations have been viewed in a purely hydrodynamical way. The first approach excludes cases which can be of considerable interests, for it fails near a plasma edge. The second loses all sight of the structure imposed by the orbital moti… more
Date: December 2, 1954
Creator: Tonks, Lewi, 1897-1971
Item Type: Refine your search to only Report
open access

Extrusion Cladding of Fuel Element

Description: From introduction: "This investigation was undertaken with the general objective of determining whether uranium core could be sheathed with aluminum by an extrusion-cladding process. The ultimate objective of this work was to determine the feasibility of extrusion cladding flat plates of uranium."
Date: March 22, 1955
Creator: Slunder, C. J.; Fiorentino, R. J. & Hall, A. M.
Item Type: Refine your search to only Report
open access

The Fabrication of Subassemblies for the Supercritical-Water Reactor

Description: In studies of the fabrication of fuel subassemblies for the supercritical-water reactor, the limited ductility of stainless steel-UOâ‚‚ fuel sheet made the fabrication of corrugated-flat-plate-type subassemblies impractical. A fabricable MTR-type assembly, 5/8 in. square and 30 in. long, was developed. Methods for edge cladding fuel sheet were developed and a brazing alloy, GE-75, was found to be corrosion resistant in supercritical water.
Date: August 16, 1954
Creator: Keeler, J. R. & Hare, Alan W.
Item Type: Refine your search to only Report
open access

FMPC Solvent Treatment Area - Process Design

Description: This memorandum presents the process design for the solvent reast area of the Feed Materials Production Center. The purpose ofthe transmittal is to provide the basis for the detailed mechanical design and layout of this section of the refinery. Drawings, flowsheets, and specifications are included.
Date: July 6, 1951
Creator: Pfeiffer, Carl & Maerker, John B.
Item Type: Refine your search to only Report
open access

Grain Refinement of the As-Cast Uranium-5 w/o Chromium Alloy by Ternary Additions

Description: Abstract: "Refinement of grain size of the base uranium-chromium eutectic alloy (uranium-5 w/o chromium) by ternary additions is discussed. Thirteen additions to the base alloy were investigated, and three additions were found to exhibit worthwhile grain-refinement tendencies. The three alloys, uranium-5 w/o chromium-0.2 w.o molybdenum, uranium-5 w/o chromium-0.2 w/o germanium, and uranium-5 w/o chromium-0.2 w/o niobium, were heat treated to produce final grain-size structures of between 0.015 … more
Date: July 5, 1955
Creator: Saller, Henry A.; Dickerson, Ronald F.; Murr, William E. & Bauer, Arthur A.
Item Type: Refine your search to only Report
open access

Initial Measurements on the Angular Distribution of Deuterium Plasma Produced by a Pulsed Spark Source

Description: Abstract: "The deuterium plasma which is ejected by a 6000-ampere pulsed current through a rail-type spark source has a yield in the forward direction which is a factor of 5 to 10 greater than that in the perpendicular direction. This effect is believed to be due to the magnetic propulsion of the plasma."
Date: March 24, 1955
Creator: Bostick, W. H.
Item Type: Refine your search to only Report
open access

Ionium Recovery Plant Design Report: Topical Report

Description: This report documents the study of the recovery of thorium by solvent extraction in pilot plant pulse columns, using a filtered liquor from nitric acid digestions of the raffinate cake produced by the ethyl ether extraction of uranium from pitchblende.
Date: April 15, 1959
Creator: Edwards, R. M.; Fariss, R. H. & Werkema, R. G.
Item Type: Refine your search to only Report
Back to Top of Screen